👇WeldTube Store👇 www.weldlife.com

I loved this test out of all the processes I’ve done, this one was relaxing for some reason. I don’t know if it was the sound or the smoothness of the welds after they were finished but it was my favorite.

Good job!🔥🔥 nice vertical flux-core👍👍

Nice work Abraham 👊👊

BIG THANKS AND APPRECIATES YOU MAN FOR THIS WELDING TEST VIDEO 💯 👍

Very few people mention to preheat the test plate before welding or not to let the plate get too hot between passes.

Thanks buddy! Keep it up👍👍 much appreciated.

ONE OF THE BEST WELDING JOB I HAVE SEEN ,

I got a weld test coming up these videos help

Could you guys do video on demagnetizing pipe or just steel in general for welding, thanks

Great video 👌

Don't take the test-welder's equipment for granted when you go in to test. Nothing burns like getting halfway through your root pass to discover the guy before you plugged half the gas-ports in your diffuser with overhead BB's even though the tip and visible portion of the nozzle looked clean. Always pull the nozzle off and make sure the diffuser ports are clean, and that your insulator is in good condition in addition to setting your contact-tip distance. A bad insulator makes putting in your first few passes on a 1" plate test feel like playing Operation, and you end up focusing on not brushing the faces of the bevel instead of watching your bead.

Did this on a miller that was only meant for mig, got it to work for flux core dual shielded but had to lower the amperage because it just was not working, melted the crap out of 3/8’s plate.

I learned alot thru this channel Can you do a 6gr flux i would love it

Bruh hold up. Am I The only one who caught that abe is doing a duel shield process but selected the "Flux Core - No Gas" setting lol. Good welds either way brotha. thanks for the vid

Thanks Abraham, and what about Fcaw open Root on 2-3-4 G position, with root gap , also with and without ceramic in the back, is it possible?? Is it recommended? Thanks again Bro

Good job

Another hit 👍

Good job & nice smooth welding I'm 6G welder Tig Mig Stick

Nice video Sir Technical

Also DON'T use "open ended" hand protectors, when doing overhead fluxcore. As the slag falling off will get caught in the open end. Use closed ended "mit" type protection.

Very good 👍

MTS 275 EVERLAST big mach. with a small price they kill it with all the fixtures they put it on burn back and inductance very handy

Is that ostrich skin on the face shield? Luxury! 👑

I preheat 1/2" & above after im all tacked up & set to weld. You dont have to heat it blazing hot but what you want to do is "sweat the iron" meaning you can be in a 115 degree test shop & if you preheat it, i guarantee you will see moisture bleeding out of the plate. What this does is not only help eliminate Non fusion but help the metal filler bond better with the parent metal. When I test on heavy plate or pipe i normally will use a temp stick but you can cheat by when the iron starts smoking or if your testing out on tool steel material it will change colors.Another thing your pre heating for is to avoid "Nickel Inclusions". On a break test they will show up when the parent metal & the filler material are not hot enough to blend in. Always try to run as hot as you can hancle it without blowing "buck shot" everywheres or putting most of your filler metal on the floor instead of your test. Best things most times is following the WPS. I've tested out on jobs where they're so nit picky about heat input that a inspector will shoot your test specimen with a gun after every pass. They will give you a tolerance but most times its not very much. Also don't try to "hog" the iron in, run as many multiple passes in as possiable. Hogging in the iron will alot of times guarantee you to trap slag. Preheat, run as many multiple passes as you can or allowed to do, keep it clean & be courteous to the inspector or the Q.C. They can make or break you on a test for the simplest mistake that is actually passable but still gives them the right to bust you.

Nice bro very good. Job.

Good vídeo

Could you do a 2g horizontal weld test with a backing strip from start to end?

Backing strip is will be welded also to the test plate itself or not? Because if pass the root i think it will be welded also.. Anyone can explain? Thankz

Great👍👍👍 mate

You should have a video with proper grinding of undercut and clean up in between welds nice vidieo

At the welding school i go too they dont allow weaving with fluxcore just straight stringer beads

tanks my frends

Where can I buy a heat pad like what you show in the video?

Try using Lincoln NR 232 .068-.072 wire. Use a Lincoln ln-25 box. No gas.

Nice..!! Good job... I like this chanel....!!!

Alright 😎😎👌 Everlast😎😎👌

I know that for the root pass the wire speed and volts should be on the higher side for better penetration and because the plate is cold. But as the passes stack, are the settings changed? Is there any benefit to lower wft and volts? Or to keep the same?

Where do you get the heat proof arm shield

I may have missed it, but what diameter wire were you running. Great vid. Thanks!!!

Awesome...

How much voltase and ampere do you used and how many gas level do you use ?thanks before. From indonesia

Awesome

I like this vidio mr... from indonesia

Muchas gracias 🙏🙏👌🙏

Alguém no brasil sabe onde comprar esse "Heat Pad" Esse protetor para o calor n mão?

Any suggestions for 3g Fluxcore open root going uphill?

hi bro. what is the best mig setting for 1.6mm tubing steel

Good

Nice

Your title says dual shield . What gas were you using with you flux core wire? 75/25 ?

Why is it so difficult to lay in a smooth root pass on the 1inch plate?

Nice video / canyou make 2G butt joint on the ame welding FLUXCORE Thank you

I love slag peel. What wire are you using? I never get slag peel with flux core, nr 211 mp e71t-11, also holbart b21. I usually use .035.

I’ve got a test tomorrow flux all the way out, no backing plate 1/8” gap 3/4” plate.

Is their a video out there for Aws D1.1 1" plate 3g?

Everlast 211si can i weld a 1” plate. ( i want to practice my 3g position) arc weld.

You guys need to do a nr232 weld with a ln25 feeder

Great video Abraham, how do you like that MTS 275? That things a beast isn’t it?

Is the best you, by Welder from 🇮🇩🇮🇩 Indonesian

What wire size were you using?????

Whats up guys, love your content. Is it to much to ask how to regulate your flux machine? Like what to look for, what it should sound like, how much is to much when it comes to wire speed? I appreciate you all. Thank you!

❤Good job sar ❤

What are the temperatures he used??

What tipe a wire do you use what Brend

Where can I get that arm pad?

Did he mention the size of wire he was using?

Parabéns chouuuuuu

Un maestro

Hey where i can find those hat you have?

How are you , what is the right way to weld with flux core wire its better dragin or pushing .. If u guys can help me

Another great video Abraham!

Is it better to get certified in stick welding or flux core ?

I need a video that shows Flux Core 3G with no backing, if anyone knows of one.

What kind of wire is that

Sir from rootpass to capping only one setting of ampers and vlotage?

I burnt through those plates like butter with those settings 😅

What is the wire size and type

Cool video Abe--Let me hook you up with a proper headband set,,,

Ou uma legenda em português brasileiro. Obrigado.

What wire size??

When you have welded for 45 yrs. You tend to get certified in a lot of different metals such as aluminum stainless steel alloy 360 Encinal and chromoly. . I have put in 20 years of offshore welding with stick Rod 7018 filler on pipes for flow lines and use 6010 to put the beads in the root pass. Also use mig wire TIG welding in flux core. Yes I am a old timer ✌♾️💯

I never removed the slag when welding the cap pass.. too many bbs gets on the cap...stays cleaner..never had a problem..11 yrs

Can you guys do fluxcore same process but without a backing strip? I had to take a test 1/8 gap without back strip, but blew it on the root was my first time taking a test like that. Fluxcore all the way 3g Thanks guys

Help me to know issually Current please

How much gas flow are you running? 25?

Do you have to go uphill to pass this test or could you go downhill too?

You're so close you could lick the plate my guy

Terria que ter uma tradução pera português brasileiro.

hi Bro I am same working in dubai

Oh my God it's Abraham

Hard to believe that weld is stronger than the 3/4 inch plate.

3g p How many gaps in position

Volt a wire please for root a second pass

USA welder?

Abe: Flux Core gets Hot, wear a Heat Pad Also Abe: Uses said heat pad to rest his arm on, Not to shield the heat… 🤦‍♂️😂🤣

My machine won't spark up on Flux mig

You mentioned weld procedures but didn't say anything about how they arrived at those procedures thorugh testing and manufacturers recommended parameters

Deberían hacer los vídeos en Español latino también

I'm working on 3g Flux Core. The problem im having is that I keep blowing a hole on my backer bar. My setting are at 180/21. Can someone give me some tips? Thanks.