In this video I decided to add a couple small upgrades to my 24th scale RC cars and run them on my Mini crawler course SCX24 and the Enduro24.
Пікірлер: 24
@think2cre813 жыл бұрын
Good video ... the courses look great . Definitely a challenge.
@jamesflory1593 жыл бұрын
I have the RC4WD tires on my element. You have to tighten the nut down with only 2 of the hub screws in with needle nose pliers. :) Also I modified my servo mount to get more travel out of my front shocks on my Element.
@patrickmueller3773 жыл бұрын
I had a similar issue . I endeded up taking the socket to my belt grinder to thin the wall down . Works slick
@jdsrcs80613 жыл бұрын
I use some grease on the those little pieces. It helps keep them in the hole so they do not slip out as easy.
@UpperLeftRC3 жыл бұрын
Great advise, I’ll have to do that also, thanks! 👍🏻😄
@carsongreen21693 жыл бұрын
Just a tip, for taking off the body along with the hinges, try using body clips where the screws go. It is easier and faster that way
@UpperLeftRC3 жыл бұрын
Great tip! 😄👍🏻
@DFDuck553 жыл бұрын
I was out for a crawl with a 1/12th scale truck and lost one of those pins. I wasn't ready to quit so took a body clip, since I had a bag of 100, and cut a bit of it off the right length. When you're out in the field you do what you gotta do to get back on the trail. It was slightly smaller around than the original pin but works well enough that it's still in there 2 years later.
@RC-CARS-WORLD3 жыл бұрын
Great video my rc friend 😀
@oregonscalespeed54973 жыл бұрын
cut the top of the servo mount off it will give you back the clearance that was loss, I had the same problem of my C10.
@rekozma3 жыл бұрын
Them little pins you "lost". Ya I lost one too. I just cut a trim nail down and used it. It's working fine. Homedepot. You can pick up a small box for about $5. Them and your dremel and you have a about a million pins. Hope this helps you in the future. Cheers.
@UpperLeftRC3 жыл бұрын
That does help, thank you! I will probably go to Home Depot today 😀👍🏻
@purepr2010 Жыл бұрын
You can do it 😀
@gulogulo98673 жыл бұрын
If you loose your wheel hex pins, just cut down a paper clip to fit
@vinnyisntgud72213 жыл бұрын
I cut my servo at an angle so it could guide itself between the rails. Still isn't perfect but better then how it was before
@callumj39843 жыл бұрын
That’s it... you got to trim those corners off, where they touch the chassis on either side. Enjoying the vids keep it up dude 👍🏽
@legendarypot8oanimates1603 жыл бұрын
Congrats on 100 subs!
@UpperLeftRC3 жыл бұрын
Thank you! It’s very exciting!
@garettbodel30022 жыл бұрын
When working on RC cars especially little one. Get yourself a white towel good maybe even just go to the store and buy one so dedicated to working on your car yoga Grace and all sorts of shit on it. Screws and parts and things won't bounce off the table just stay right where they are and you won't lose stuff
@Scrimjer3 жыл бұрын
That rear diff, cover on the deadbolt kept making mine flip, just a thought
@UpperLeftRC3 жыл бұрын
I’ll have to look at it a little closer and see if mine has the same problem, thanks for the heads up 👍🏻
@ptshyu23 жыл бұрын
I ran without hubs for awhile didn’t know there was suppose to be anything there
@Yea1234yea3 жыл бұрын
What do you use to rase up the corses off the ground??
@UpperLeftRC3 жыл бұрын
TV dinner trays 😂 I’ve been looking at some saw horses to lift them in my room but these work for now