B18 Swap Parts List and Guide || Engine Swap Parts List

Рет қаралды 157,631

7 жыл бұрын

B18 Swap Parts List and Guide || Engine Swap Parts List is compiled to help anyone with a Civic engine swap or and honda engine swap that they are looking to complete. I'm not drag racing, but I will say this thing rips due to being lightweight and Honda should have put the B18 swap into all honda civic hatchback of this era. Truly changes the whole character of the car and the fitment is spot on.
"Project Civic" Parts listed below w/ option numbers. This applies for B18C, B16a, B16B, B18a, B20, etc
Hit SUBSCRIBE and turn on Notifications for new videos! - goo.gl/LLojcS
Time to run through all of the parts I used to swap a OBDIIa B18C engine from an Acura Integra GSR into a OBDIIa Civic DX hatchback.
Subscribe to Follow My Build! - goo.gl/hi9yB2
Hondapartshero harness - goo.gl/fguxyK
Civic SI T Bracket - goo.gl/iTB1WY
B20 CRV 2 post Bracket Mount
Or goo.gl/JHzdTK
Civic DX Transmission bracket and mount
Civic DX Clutch hard line on engine and transmission bracket mount
Or Engine Mount Kit - goo.gl/dBcEKc
Integra GSR upper/lower Radiator Hoses - goo.gl/79lKgj
Integra GSR heater hose - goo.gl/uXiRwA
Yonaka exhaust - goo.gl/t8sW0u
This guide was hopefully thorough enough for all performing a civic swap with an OBD2 start. I am planning to create the honda engine swap guide for other Honda civic chassis and OBD1, 2 cars. The wiring is really all that changes. To complete this build, the honda civic swap cost is actually very low for anyone looking for a fun budget civic project car.
"Project Civic" Hatchback Build Episodes:
Episode 1: goo.gl/2ZWgT1
Episode 2: goo.gl/Uk23aC
Episode 3: goo.gl/knN406
Episode 4: goo.gl/JsGwAv
Episode 5: goo.gl/9S1XFn
Episode 6: goo.gl/D3Bxfy
Episode 7: goo.gl/Trz5xc
Episode 8: goo.gl/26iosP
Episode 9: goo.gl/u00iAI
How To Compression Test: goo.gl/kqVwdi
Swap Integra Seats into a Civic EK: goo.gl/HvuZ2r
B18C Swap Parts || Civic Hatch How To : goo.gl/7eahQe
Honda B18C Engine Swap Update and Pulls: goo.gl/21PGD5
Flipping Car Parts On Ebay And Craigslist: goo.gl/9VQpoN
Welcome to Stauffer Garage! I am beginning an EK civic project car build and will be documenting the entire process vlog style along with tutorials and updates. I have picked up an Integra GSR for cheap and will be pulling the B18C and all other components that will fit and putting them onto my Civic. Goals for this car are to make it daily but it will be primarily a track day weapon! Boost might come into play along with other mayhem! Not a drift car build, but this will certainly be closer to a race car build when all is said and done for this little hatchback
Be sure to subscribe to follow along with this build and the other projects that come along!
Business Inquiries: thestauffergarage@gmail.com #stauffergarage
#carcleaning #cardetailing #powerwashing #maddetailing #ammonyc #thedetailgeek #detailgeek #wddetailing #autodetailing #disasterdetail #detailing #interiorcarcleaning #carcleaning #interiordetail #filthycardetailing

Пікірлер: 222

@pandamike209 6 жыл бұрын

throttle cable on big thing u forgot

@StaufferGarage 6 жыл бұрын

Yes you are correct thanks for adding

@ap3xguardian121 4 жыл бұрын

yes i used an itr throttle cable with my swap

@keapeer6669 3 жыл бұрын

Is this for every b-series swap? Sorry I’m a noob also this this go with any b series swap?

@buildhumbly7905 7 жыл бұрын

Brother thank you! I've been wanting to do a gsr swap on my ek so this is gonna help a ton! 👍🏼

@StaufferGarage 7 жыл бұрын

Happy to help! Let me know if you have any questions!

@youtang 5 жыл бұрын

Hey I just remembered that your videos really helped me out with my GSR swap. Your videos were the most well put together in regards to the B18C swap. Thanks to your videos and some really well written forum write ups, I was able to start up on the first crank. The only CEL was there for not having the first o2 sensor plugged in...the exhaust manifold on the 94-99 GSRs are too short and the flanges are postioned differently. Anyways, thanks again!

@missle5026 7 жыл бұрын

Thank you for the vid I have a 2000 civic Dx hatch that I plan on doing a b18c swap on and this vid helped a lot!

@StaufferGarage 7 жыл бұрын

Glad I could help you out!

@tubejim101 7 жыл бұрын

Thank you for making this video.

@ej8mods160 2 жыл бұрын

Thanks you so much for the detail video your the best 👍🏻

@CeeJaay300 7 жыл бұрын

yes do a obd1 - 2 swap talk

@bradlyfan 6 жыл бұрын

crisJv I did it once want my advice?

@jrentas3239 5 жыл бұрын

Agreed

@linglingz3322 5 жыл бұрын

Yes

@olivermoes-okun2468 3 жыл бұрын

@@bradlyfan I have b18b1 from 97 Integra and putting in my 00 civic dx hatchback. what ecu should I use? I have d16y7 harness on and a obd2 to obd1 harness so I can convert to obd1 if that's better

@shannonferguson2000 6 жыл бұрын

Smooth video!!!!

@rickarchibald1369 2 жыл бұрын

This really helped!

@ivtecudont241 7 жыл бұрын

Thanks for the informative video .. and yay looks like I'm pretty set for my swap this week 😁

@StaufferGarage 7 жыл бұрын

How'd the swap go?

@ivtecudont241 7 жыл бұрын

Stauffer Garage going to be dropping the y7 and installing everything on Friday, it's going to be a long day but everything SHOULD go as planned .. I'm excited

@StaufferGarage 7 жыл бұрын

+ivtecudont241 You'll encounter a few things but its straight forward to be honest

@ivtecudont241 7 жыл бұрын

Stauffer Garage I'm sure , nothing goes correctly as planned ... now because I'm dropping in a jdm b20 block(GSR head) it has no ckf so I gotta do the ckf bypass trick .. technet.ff-squad.com/ckftrick.htm I still need the upper radiator hose and I think I might get the thermostat as per your recommendation ..(I'm doing the timing belt water pump etc etc as well)

@ivtecudont241 7 жыл бұрын

Stauffer Garage remember you said I'd run into something ? I did.... my b20 did have a dented oil pan and the oil pickup was bent ... (had a junk GSR block laying around so I was gonna use that for some donor parts) so yeah I dropped the oil pan after I drained the oil from the b20V andddd metal sediments galore ... metal shavings galore ... that little time that the car had running with the damaged oil pick up wreaked havoc on the bearings ... because it's a low mileage jdm block the crank is good but the bearings took the hit .... gonna junk the block or save it and build that but for now gonna get a high compression b20 block and throw my vtec head over .. on that

@monstahtron 7 жыл бұрын

very informative video saving this for whenever my d16 blows lol

@StaufferGarage 7 жыл бұрын

Lol, I couldn't wait for mine to do that! Wasn't going to happen for a long time!

@codcade 2 жыл бұрын

Same lol, just got a free hatch lol, Has a d16y7 and it’s got 287k and just eats oil lol

@1BadRAMLimited 2 жыл бұрын

Thanks

@killer1cam606 4 жыл бұрын

Shift linkage b series you'll need that too

@TheWorteldrie 6 жыл бұрын

Ive got an LS swapped 97 civic EX and it runs good but the check engine light is on (which I'm not freaking out about) and I'm sure I did something wrong lol. Vtec wiring harness to non vtec motor. Lots of plugs left hanging..

@jimboi7616 7 жыл бұрын

Interested for a vid on a jdm gsr b18c into an ek. I have researched this online and have a good grasp on how to do it, but I would like to have your input as well. Btw, Keep the build vids coming dude! 👍🏽

@StaufferGarage 7 жыл бұрын

+Jim Boi thabks a lot! I can look into it but know the biggest difference is in the crank position sensor on the front. You need to bypass or switch the oil pump to a hadn't version and add the sensor

@h23beltran24 7 жыл бұрын

yes do a obd1

@cheeseburguhgaming9581 2 жыл бұрын

yeah i was debating to engine swap my car too but i was like forget it ecu getting vtec chipped or getting a s2000 hondata t brakets and all these other things i rather just throw some arp head studs ungraded cams and turbo the car clean the engine grime and have a turbo exhaust adaptor to bolted on to my exhaust axle back and muffler

@3030rey 5 жыл бұрын

Something more can change on plugs, like idle plugs alternator plugs ignition plugs ?

@anthonyorozco452 5 жыл бұрын

please make a video with obd2 for a swap obd1

@30minforasn 6 жыл бұрын

Great vid!!

@djsonicc 6 жыл бұрын

Tons of information. I don't understand why people are disliking?

@StaufferGarage 6 жыл бұрын

Beats me man! Thanks!

@dkinley334 3 жыл бұрын

My dream is to b18 swap my ek sedan but dang it seems like such a job

@nilbog3641 3 жыл бұрын

Any recommendations for an ef hatch

@luisramos2737 7 жыл бұрын

Hi James

@StaufferGarage 7 жыл бұрын

Yo whats up!

@jimhiscott2918 2 жыл бұрын

Ditch obd2. Always go obd1

@khyrone5193 4 жыл бұрын

Wondering if the B18C engine is a good engine swap for a Peugeot 205 GTI

@peterboyles5376 7 жыл бұрын

Thanks for the video and I have a 1999 Honda Civic ex with a D16y8 VTEC and can I just use the harness from the D16Y8 to the B18C

@StaufferGarage 7 жыл бұрын

Essentially yes, if it already has vtec. The only thing missing would be the wiring for the dual runner manifold on the B18C

@JamesJonahJameson-MM 2 жыл бұрын

Did you ever make a video for OBD1 to OBS2 swaps? I live in CA and I’m beginning to collect parts for a 1999 B18C5 that will go into my 1992 Honda Civic CX non Vtech hatch. I will be buying the ATK remanufactured B18C5 engine. 4 month waiting list.

@JamesJonahJameson-MM 2 жыл бұрын

OBD1 to OBD2 swap

@seavick7001 7 жыл бұрын

Yeah I have a obd1 gsr and have an ek as well need help asap

@StaufferGarage 7 жыл бұрын

will look into this and try to throw a tutorial together!

@cruzperez9452 4 жыл бұрын

What about for a 1999 Honda Civic EX with a D16Y8? Do I need anything more or less?

@EddieSwaggy 2 жыл бұрын

Hey man thanks for the video! I just did a b18c swap as well and i'm having fuel issue did you have to change your fuel pump?

@bootzmckenzington 2 жыл бұрын

Having the same issue. Mine is running lean . Looking into gsr fuel pump. Might be your issue to

@speedybede4639 2 жыл бұрын

Okay so, I’m planning to do a B18C2 Swap on my 1st gen CRX si(1985)… after some research I realize that OBD-1 was introduced to the us market in ‘92. Will this cause me trouble if I’m OBD-0 on my ECU?

@luisaguilar-kh1se 5 жыл бұрын

Please make the obd1 into obd2 please

@SAViOR13100 7 жыл бұрын

Interesting that you used the d16 radiator, mine seems to be too small for my hoses.

@SAViOR13100 7 жыл бұрын

As far as the bungs that come out of the radiator itself

@StaufferGarage 7 жыл бұрын

+REAMS 2 I reused the d16 clamps on the gsr hoses and it sealed great and haven't had any issues at all

@SAViOR13100 7 жыл бұрын

Stauffer Garage I see I see. I just feel like getting a new one since my d16 overheated too many times so I figure get a fresh one

@StaufferGarage 7 жыл бұрын

+REAMS 2 mine was less than a year old and I didn't want to just toss it. If you are in need of a new one pick one up!

@leviorourke7498 3 жыл бұрын

Will this parts list be accurate for the 1990 ef civic si I have

@justinmangubat7764 4 жыл бұрын

I have a 1996 B18C1 engine and I'm hoping to put it in my 1991 Civic Si. What parts should I be getting? Any tips aswell? Thanks!!

@WexfordGamingNetwork 3 жыл бұрын

I have a dc1 integra. (1.6L non VTEC) , what exactly do i need? Or any tips? As obviously the chassis etc is the same as the dc2 , so its just the Loom , ecu , mounts , and?..

@mrsemifixit 2 жыл бұрын

Can you just swap stock ECUs or need something else?

@see012392 7 ай бұрын

did you keep the powering steering? what did you use for the power steering backet if you did?

@marseanf3039 4 жыл бұрын

For the ac what belt do you use?

@livinglargeandfree8322 7 жыл бұрын

I'm gonna do this in my 98 crv

@StaufferGarage 7 жыл бұрын

YES!!! That is something I want to do and boost it! Sleeper!

@livinglargeandfree8322 7 жыл бұрын

that's what I was thinking...but mine is also lifted.

@SamyyCJR 7 ай бұрын

what parts would have to be different in order for this to work with an EG 1992 hatchback ?

@quinceyclements2244 4 жыл бұрын

Will these parts work on my 98 EJ

@chrisasaurus 5 жыл бұрын

B swap on a 79' cvcc Honda

@loganhoward4599 2 жыл бұрын

Sorry so why do you need the d16 harness? I'm buying a package that includes the entire wiring loom for a b18c so i should just use that right ?

@marcialgarcia112 4 жыл бұрын

What about the trasmission torque mount ? I got the 99 ek hatch but the stock mount doesnt work looks too big.

@bigt_money615 5 жыл бұрын

im guessing that all this applies to a 96 EJ

@jcreary100 6 жыл бұрын

i have a 1999 honda civic lx d16y7 tubo, i would like to swap in a b16a sir ek9 and i would like to keep it obd2 for emissions purpose, what do you recommend. any help would be thankful.

@enricocrevecoeur5255 4 жыл бұрын

What throttle cable do I use?!?

@aaronpitts2762 5 ай бұрын

Hi, will this apply to the eg6 civic?

@benmontgomery5608 4 жыл бұрын

Can you do a b swap to a 2002 4 dr ex civic

@chulohernandez8521 5 жыл бұрын

Im going wit a B18b1 in my 98 dx but it isn’t vtec and the dx obvio none vtec can i also use that harness or would have to just find the harness and I also have a ex harness fully un cut Lmk

@chriscole9621 3 жыл бұрын

What else do I need to do a d16 auto to a b series manual?

@tubejim101 5 жыл бұрын

How can I bolt in the power steering pump? b18c1 going into 98 EX Civic. Have the gsr brackets, and pump, but the high pressure hose does not hook up. Thinking I need a ps pump from a 99 SI??

@StaufferGarage 5 жыл бұрын

No you can reuse the Civic pump. Just need a bracket from the CRV B20. Check on Honda-tech and search for the exact one. I was able to reuse the entire Civic PS system.

@marcialgarcia112 4 жыл бұрын

Help please i am having problems with my 96 gsr swap into my 99 ek hatch, The ecu coneccion on the ecu its different from my ek civic, I bought a obd2b-obd2a jumper harnes but still cant fit 😥

@luisramos2737 7 жыл бұрын

Nice videos...Did you upgrade your fuel pump? I have the same setup but it seems like my stock fuel pump is not flowing enough fuel. I'm thinking of upgrading to 255 walbro fuel pump. Let me know ur opinion thanks

@StaufferGarage 7 жыл бұрын

No, and I would doubt that you would need an upgraded pump unless your pump is going bad. The stock pump can flow plenty of fuel and if anything you could upgrade your fuel pressure regulator and adjust that pressure to flow more through your injectors first if you truly have the same setup as me.

@3030rey 5 жыл бұрын

What change if I want to to do swap but my civic is obd2b what change if the b18c dc2 is obd2a I can do the jumper on the ecu to run obd2a or p28

@alexmartinez-vj3eq 3 жыл бұрын

Is d16y5 harness plug and play on b18b1

@louiselorenzo9458 3 жыл бұрын

What is the motor on the brake for that?

@levonlyons 2 жыл бұрын

I know I'm old but I still want to do a Jdm engine switch I need to get all the cash to make this come to my life goal its either this or a luxury built car

@frankmanzur5904 4 жыл бұрын

I have I 96 civic with a 97 b18c jdm and jdm p72 motor in it but body is trash ,so and im going to strip everthing from that car to a 2000 civic coupe automatic whats the best harness to get on a budget

@Georgio_619 4 жыл бұрын

How easy is it for a del sol b16a3

@henryfilip4325 5 жыл бұрын

Does anyone know if this is the same for doing a b18 swap into an ep1 chassis?

@DamonPlayss 2 жыл бұрын

Would this work for a LX sedan ?? I have a 97 and I’m looking to b18 swap mine as well

@prashanthperananthasivam3416 6 жыл бұрын

I have a non vtec 00 ek obd2b but have a obd1 97 gsr what harness do i use

@marcialgarcia112 4 жыл бұрын

So If i got the to b20 crv post mounts i shouldnt need to buy any adicional mounts right ¿ Its a 99 ek.

@tubejim101 7 жыл бұрын

Is the B20 CRV 2 post Bracket Mount, an OEM part? Having trouble finding the OEM part number.

@StaufferGarage 7 жыл бұрын

I think this is it: 1910-P3F-000 I grab mine out of the junkyard from a CRV. www.bernardiparts.com/Honda/Parts-List.aspx go to like a 98 crv ex 5 spd under the engine:cylinder block/oil pan section

@tubejim101 7 жыл бұрын

Thank you.

@danielstephens4420 5 жыл бұрын

This is wrong ! Crv post is too tall.Make motor sit slanted down about 2 inches on one side.You want the 99-00 si post mount.

@VietTranHB 7 жыл бұрын

Can we passed on Smog check ? I heard that we can make swapped engine legally whenever the emissions pass the government's requirements

@StaufferGarage 7 жыл бұрын

Yes if you retain all the charcoal canisters and swap everything over from a GSR front clip.

@stevensweets805 6 жыл бұрын

Hello sir, I have trouble with the connecting the wiring harness, please show how you did it. I have a p3x ecu currently installed. It only has 2 plugs while the p72 I have has 3 please help

@stevensweets805 6 жыл бұрын

Also, did you swap distributors because my GSR plug is different from the D14s distributor

@samueltaladay8890 3 жыл бұрын

I have a 2003 Civic 4 door 5 speed. Need more power and need help

@adrianreyes330 6 жыл бұрын

I have a 1998 civic dx, what engine series do you recommend swapping it with? I want to swap it with a b18 or b20

@StaufferGarage 6 жыл бұрын

B18C all the way. Its the highest displacement B-series with vtec and they will run forever and take abuse.

@ThePrelude1999 2 жыл бұрын

I'm thinking about doing an engine swap a b series maybe b16c or b18b1 engine in my civic butts it's a 2000 civic ex Is it possible?

@loveheraye408 5 жыл бұрын

I’m swapping a obd2a b18b1 into my obd2b 00 ex civic will it be plug n play? Or will I have wiring issues

@StaufferGarage 5 жыл бұрын

You will have to do a couple wire changes I believe. Search on Honda-tech.com

@josephquintana1970 5 жыл бұрын

What’s the difference between b18c and b18c5? Do both of type r engine apply to this video or they slightly different

@brrbrr474 7 ай бұрын

4 years later im doing my first civic swap with a b18c i did some research and figured out the b18c is the jdm verison and the c5 is the usdm verison. the only difference comes with the match transmissions. the final drive is shorter on the jdm verison.

@keithbegley888 6 жыл бұрын

Is it the same with the coupe, are the engine bays different hatch vs coupe?

@StaufferGarage 6 жыл бұрын

Nope! Even the 4doors are all the same front end :)

@Cardmonger 6 жыл бұрын

If i had an ls. And say i wantes to just do a gsr swap. Would al i need be the engine, ecu, and the gsr wire harness? Or do i need pig tails also?

@StaufferGarage 6 жыл бұрын

Engine Ecu and reuse the LS harness, you would just need to add the harness I have linked in the description box for vtec, dual intake manifold and crank sensor.

@bull7618 7 жыл бұрын

What if it's a d14 ek series civic? know anything about wiring for a conversion in that case?

@StaufferGarage 7 жыл бұрын

It should be pretty much the same and just add in the harness I suggested in this video for Vtec and dual runner manifold found on the GSR B18C engine

@EdithSanchez-qe4hz 6 жыл бұрын

Whats the best swap for 91 acura integra

@youtang 5 жыл бұрын

If you're lucky, you find a B17. Or, try looking into building a LSvtec.

@nichigd6863 Жыл бұрын

If I have an integra ls 1998 does it slide in or do I need any other parts ?

@StaufferGarage Жыл бұрын

You will have it easier but there are some parts that will be needed that you can get out of the oem honda parts bin

@christophersmokeyday622 3 жыл бұрын

I just bought a b18b1 and trans with “stage 3 clutch” for $200 bucks. It was previously in a 97 ek civic. How can I tell if it is the correct obd for my 2000 civic? I have a stock d16y8 ex sedan

@christophersmokeyday622 3 жыл бұрын

I’m only 19 and I’m new to all of this stuff. quarantine has me bored so I want to start learning new stuff. bought all the tools I need! just need to learn it all now lol

@salvadordelgado4983 Жыл бұрын

Hey man, i recently bought a 76 cvcc and my motor is no good, been thinking about doing an b18c swap but i have absolutely no knowledge of swapping engines, is there any tips or specific websites that i can look at ??

@StaufferGarage Жыл бұрын

Honda-tech has everything you’ll need from diagrams to step by step posts

@reddragonx8799 5 жыл бұрын

I'm trying to swap my engine to a B18 I have a 2000 Honda DX what parts do I need to be able to swap my engine with a B18?

@StaufferGarage 5 жыл бұрын

I would re listen to this video and what year is the motor?

@datbenzdoe5157 7 жыл бұрын

So I have a da9 and I just got a obd2 gsr and am about to do the swap as far as I've read it's basically a direct swap besides the dual runner intake manifold which I already bought a skunk2 manifold and 70mm throttle body and I need a p28 or p30 ecu so I need to wire the vtec but I got a vtec wire kit and I believe that's it correct? Thanks.

@StaufferGarage 7 жыл бұрын

That sounds about right!

@michaelwilliams6922 5 жыл бұрын

Can't you just take out the d series harness and put in the b series harness and get the right b series ecu

@dreamer2355 7 жыл бұрын

It would have been nice if you covered the exhaust setups too such as if anything is plug and play or if welding needed to be completed. :)

@StaufferGarage 7 жыл бұрын

+AutoTechDale thanks for the suggestion! Will do in the next review and do a full walk around of the civic and discuss

@dreamer2355 7 жыл бұрын

Stauffer Garage That sounds great. Its very hard to find the correct information out there on what to do with your exhaust after a swap seeing as the B series manifolds are different lengths

@EdithSanchez-qe4hz 6 жыл бұрын

What about 1991 da. Acura integra

@StaufferGarage 6 жыл бұрын

Depends on your budget and time! What power goals do you have?

@abcwarrior91 7 жыл бұрын

what does obd1 or 2 mean

@ZFA1738 4 жыл бұрын

abcwarrior91 on board diagnosis. Basically cars computer system

@radrepairs3134 Жыл бұрын

having trouble with the gsi tranny shift linkages, it not shifting into 3 or 4. any suggestions?

@StaufferGarage Жыл бұрын

Can it shift in the other gears no problem?

@radrepairs3134 Жыл бұрын

@Stauffer Garage its damaged internally, Thanks for the reply mate, really appreciated.

@markozettl6541 7 жыл бұрын

hi, im interested about a swap b18 vti on my currently d14a4 97 civic hatch...is that possible and what I need to prepare to have to install that swap? Best reguards (Y)

@StaufferGarage 7 жыл бұрын

Probably the same parts I have listed. The only differences will be around the wiring depending on the emissions level the car and motor are at.

@101009pm 6 жыл бұрын

I noticed you swapped into a non vtec chasis civic. How did you get your iacv to work? Did you reuse your old throttle body?

@StaufferGarage 6 жыл бұрын

In the harness I recommended it includes wiring for the IACV that you run back to the ecm

@danielstephens4420 5 жыл бұрын

Or just use your harness and search 3 wire iacv to 2 wire online.You just depin one wire and depin and relocate one wire on your harness ecu plug.Takes 5 minutes.

@blix8787 7 жыл бұрын

question. so when you put the b20 ac bracket did you use the b20 pulley or did you use the d16 pulley. reason why I went to my local junkyard and they only had one crv that had the bracket taken off already but it was missing the pulley. today being Thursday I have to wait till the weekend to see if I can swap it over but I would like some reassurement

@StaufferGarage 7 жыл бұрын

Actually they should be identical, at least it was for me! the one on the B20 bracket had bad bearings and I swapped on the D16 one and been running no issues. Visually they looked identical so I ran with it.

@blix8787 7 жыл бұрын

Stauffer Garage awesome. thank you very much. I'll do the same. Also keep up the videos I gotta say I found your videos better informed than those from Honda street garage.

@StaufferGarage 7 жыл бұрын

Glad to hear and glad you are enjoying my content! Always open to suggestions and fyi tonight new video will be out! First episode of the Summer detailing series!

@blix8787 7 жыл бұрын

Stauffer Garage awesome I'll check it out as soon as I get out of work.

@kodyking3090 3 күн бұрын

All that work and extra parts for a 290hp motor?

@Joliva124 Жыл бұрын

What about for the power steering I'm doing a swap and I have a d16y8 and if there someone that can help me what to do get an idea I would appreciate it!

@cheesus9744 11 ай бұрын

I’ve heard you need a em1 si p/s pump and your stock obd2 ek power steering lines

@hectorrentas6838 6 жыл бұрын

I have a question could you help me please I’m doing a b20 engine on my civic ek 99 what wiring harness do I use and ecu

@StaufferGarage 6 жыл бұрын

OBD2B would be the easiest since that is what is already in the car

@danielstephens4420 5 жыл бұрын

You can't use the integra ls obd2b ecu because of the immobilizer.You need an obd2b to obd2a jumper harness ($35 amazon) to use the 96-98 integra ls ecu.Best option is run a obd2b to 0bd1 jumper.Then buy a socketed chipped obd1 ecu with a crv b20 base map loaded into it.Then have it dynoed and chipped again perfect.It will run ok on the ls integra ecu but it will be lean on start up and some lean spots in the rpm range.

@cosmicfiber4 5 жыл бұрын

I’m going with a B18C1 into 96 del sol. Anybody done this? anybody know of anything additional craziness special for del sol? Also, is anything special needed for gauges/tachometer? Like a different tachometer, do engines have different redlines and what not?

@fourside4237 2 жыл бұрын

Hey dude this is late but did you ever figure this out?

@TheRichardOlson 8 ай бұрын

Same, im stuck on the rear t bracket atm

@LK-nu6mg 7 жыл бұрын

I'm thinking of swapping a b series motor into an ek but the ek has an auto tranny. so will I have any problems if I try to install a manual transmission inside?

@StaufferGarage 7 жыл бұрын

You'll just need the pedal box (gas, brake, clutch) from an integra or civic, the clutch master cylinder, manual ECM (should be with your swap), and the clutch master to slave cylinder line.

@LK-nu6mg 7 жыл бұрын

Stauffer Garage Thank you!

@nickmartinez4932 7 жыл бұрын

Can you use stock ek tq mount/brackets, i am also wanting to keep the oem look thanks in advance (using b20b ) .

@StaufferGarage 7 жыл бұрын

Absolutely, I used GSR torque mounts and all OEM honda mounts.

@nickmartinez4932 7 жыл бұрын

Stauffer Garage so use stock tq mount bracket ? With oem rubber mount

@StaufferGarage 7 жыл бұрын

yes sir.

@nickmartinez4932 7 жыл бұрын

Stauffer Garage thank you so much look forward to next upload

@StaufferGarage 7 жыл бұрын

Hopefully have one out by Sunday!

@zakattack4274 7 жыл бұрын

I need some help I guess I'm doing it the hard way b18a1 into a 99 civic ex I have the 93 Acura integra the complete car that the b18 is coming out of

@StaufferGarage 7 жыл бұрын

It should still be fairly straightforward. You are using a b series engine and might just need to get the mounts I mention to make it fit.

@zakattack4274 7 жыл бұрын

Got one more question the axles I've heard that the 93 axles will fit do you know?

@StaufferGarage 7 жыл бұрын

Im not sure on that one, Id search on hondatech. I can say for sure that the 94-01 axles will fit into the civic spindles and fit.

@1yotate 6 жыл бұрын

what part of the states are you located?

@StaufferGarage 6 жыл бұрын

Ohio

@that_Tim_guy_ 7 жыл бұрын

can you explain the difference between the Si post mount vs a CRV post mount? I have used the CRV post mount the same as you but my T Bracket has trouble fitting correctly, I've been told it was bc of the CRV post mount but I don't know if that's the case. Any ideas?

@StaufferGarage 7 жыл бұрын

+Tim Lowery do you have the civic si t bracket? The si post mount should also be identical because it allows you to use the pancake type mount used on civics. Where as the integra mount is similar to the tranny side where its a large circle mounted horizontal.

@that_Tim_guy_ 7 жыл бұрын

+Stauffer Garage yeah, every mount lines up seemingly correct except the rear bracket, the Si T Bracket, it's like the mount and motor are too close and the T Bracket is very difficult to get in place

@StaufferGarage 7 жыл бұрын

Did you get it to fit?

@that_Tim_guy_ 7 жыл бұрын

Haven't gotten to try again due to work schedule and weather but as of right now we havent..

@that_Tim_guy_ 6 жыл бұрын

Working on this later today, is there another form of contacting you? I'd like to work out this t bracket mystery bc it's quite frustrating. But I'd like to discuss this without searching for the video each time lol please respond!!