Bad Boy Mowers Maverick 50 Hour Maintenance Part 3

Bad Boy Mowers Maverick 50 Hour Maintenance Part 3 - Grease and Hardware

Рет қаралды 20,125

South Coast Fabrication And Outdoors

Күн бұрын

Last portion of the 50 hour maintenance on the Bad Boy Maverick is greasing the fittings, checking the belts, and checking for loose hardware. Time to get back out mowing!
Affiliate Links:
Lock-N-Lube Grease Gun Fitting.
amzn.to/3z7VKEM
My favorite fuel jugs 1, 2, 3, and 4 packs.
amzn.to/3pzg7aU
amzn.to/3EC2xb0
amzn.to/3JqdCzo
amzn.to/3z9UCRh
Instagram: / southcoastdad
Facebook: / southcoastfabrication
Christian
Husband
Dad
Fabricator
Outdoors-man
Fisherman
Come along for the ride as I get into various projects and outdoor greatness!
Current Production Setup
Camera: Canon EOS M50
Editor: Lightworks Video Editor
Music: Epidemic Sound
#BadBoyMaverick #Maintenance #Lawncare

Пікірлер: 30

@58bobw 3 жыл бұрын

Great video! Yes, I’d like to see the wash video on it for sure. I clean mine with a air compressor and have never washed it due to “fear of the unknown”.

@south_coast 3 жыл бұрын

Might be able to make that video happen for ya! Thanks for watching and thanks for the comment!

@58bobw 3 жыл бұрын

@@south_coast I forgot to ask you earlier, are you running regular pump gas in yours or opting for the non ethanol gas? I’ve done both but with winter coming on and one more cut left I think I’m gonna put in non ethanol this time

@south_coast 3 жыл бұрын

@@58bobw I only use non-ethanol in all of my small engines. This goes for generator, pressure washer, mowers, string trimmer, chainsaws, etc. Around here I can only get non-ethanol in a 90 octane flavor, so that is what I run.

@58bobw 3 жыл бұрын

@@south_coast same here, prices range $2.65 at low to $3.24 high. I buy 5 gals at a time

@south_coast 3 жыл бұрын

@@58bobw I generally stock up going into hurricane season and just rotate through my jugs to keep freshening up my supply. Seems to work out so far.

@rogerroger5585 2 жыл бұрын

Seems your supervisor has complete confidence in your abilities (at 3:00). He seems pretty chill. :)

@MrZipperhead16 3 жыл бұрын

This is my first mower without greaseable spindles and I hope they work out. My last 2 mowers were Cub Cadet's and I ran them to death. Just about everything on them wore out or broke EXCEPT the spindle assembly's, all had grease zerks. We'll see.

@ronaldlandry7163 3 жыл бұрын

You are missing two grease fittings you have one on a deck and one in the back underneath the mower

@south_coast 3 жыл бұрын

Finally got under there and found them. I’ll post an updated video eventually. Thanks for commenting! I really appreciate it?

@jannieanderson112 3 жыл бұрын

@@south_coast would love to see where they are. Hope to see video soon. Thank you, great videos

@JOLEBLON62 2 жыл бұрын

My hour meter stopped working within the first year on my Outlaw XP

@rayburnett3253 3 жыл бұрын

I ,too would like to see a wash video

@south_coast 3 жыл бұрын

It is on the horizon.

@sls3051 3 жыл бұрын

what size nut is used to unscrew the bolt? And for my first oil change, the nut is so tight - what's the trick to loosen it. I"m a girl.

@blakeuh 3 жыл бұрын

You missed a grease fitting on the rear of the deck you can only see it from underneath

@south_coast 3 жыл бұрын

I will have to look into that one. Thanks for the tip.

@blakeuh 3 жыл бұрын

@@south_coast actually 2 grease fitting one under the engine as well they are on the tensioners

@south_coast 3 жыл бұрын

@@blakeuh I am not far off from getting back out cutting, so I will take a look under there before I get going again. Thank you for coming back and updating!

@tomhood1700 3 жыл бұрын

Correct. It is a pump belt tensioner fitting and I would like to know how to get on it to grease it. NO ONE covers it! And certainly not the factory videos.

@blakeuh 3 жыл бұрын

@@tomhood1700 I put the deck all the way down and slide up underneath the engine and get it from there

@58bobw 3 жыл бұрын

Question: season is over here in Georgia for mowing. I just used my Bad Boy yesterday for the last time before March 2021. I want to either change blades out or sharpen them, not sure until I see them. Do you know the best way to get at blades? Hoist? Tip up? Jack stands? Home made out of cribbing block? Oil changes are one thing, getting under deck is another. Any advice/info appreciated! Thx 🙏

@carolscott4383 3 жыл бұрын

I use car ramps. Raise the deck all the way and back the mower up into position and set the brake. Jack up the front till its level, not higher or oil gets into the engines cylinders. There should be enough clearance to use an impact tool on the spindle bolts. I don't use impact to retighten, you might strip or bust bolts off... A. Scott

@tomhood1700 3 жыл бұрын

If it has a pump belt tensioner fitting I would like to know how to get on it. The mower place keeps saying you gotta get it from underneath and use a 90 degree fitting on your grease gun. I've done both and still can't get on it.

@ericplatz7200 Ай бұрын

I have a question to see if you can answer it. I have a bad boy Mavic and my steering arms one of them works real good. The other one doesn’t react as well. I don’t know if it’s a linkage or if it needs to be greased up so when I go in reverse, I believe it’s the right side I have to pull it twice as far back for it to work, the problem is I don’t know what the problem is. Everything seems to be OK.

@south_coast Ай бұрын

Are they even when you are going forward or does the right one need twice as much input?

@ronaldlandry7163 3 жыл бұрын

You are missing two grease fittings you have one on a deck and one in the back underneath the mower

@tomhood1700 3 жыл бұрын

Correct. I would like to know how to get on the pump belt tensioner fitting to grease it that is underneath the mower.

@681419 Жыл бұрын

kzfaq.info/get/bejne/kK1lfMKBxs62iGQ.html