Jolene is such a wonderful woman. She is a big help to you and always trying to learn something new. When a person isn't willing to learn something new they are as smart as they are ever going to be. I'm 72 and still learn all I can.

Very fun to watch you both work together. Jolene is a real natural. Great videos!

This is the best channel to learn how to do body work excellent job both of you guys

I used to work for evercoat did bodywork paint we didn’t recommend laying down Feather fill Direct to metal the way is lay down epoxy primer and then lay down feather fill is Polyester Primer is Porous moisture be under your primer down the road you will have problems

I know exactly what your saying. Your a great example of a great teacher. Also you have great stories! I like that your the Bob Ross of car painting!!

Hi In order to get a long lasting quality result, you should have an epoxi primer on bare metal, I have seen great paintwork getting destroyed by blisters due to no primer under polyester sprayfiller. Body guy since 1981. Keep the good work going Take care From Sweden

Chad, I have much respect for you as a fabricator and a designer. I too build cars and have for 40 years. I know what it takes to achieve the end product that you create. I only have this last comment about the primer as a bit of information that you can take or toss it out as you see fit. I have spent the last 26 years as a manufactures rep for one of the largest automotive coatings companies in the world. I have a lot of experience behind what I am talking about. A large part of my job has been helping painters figure out what went wrong with their paint job. 99% of the time it has been because the painter did not follow the manufactures directions. The directions are for optimal results. The paint chemist that developed this product knows what it will and will not do. The manufacturer of the product has spent many hours testing with salt spray, adhesion and chip resistance. If it fails, they are usually held responsible. Unless it was not used correctly. The procedure that you use will work for a while. Long term, who knows because it was never intended to be used that way. The problems will come later after the hot sun and moisture attacks the finish. Yes 80 grit will provide adhesion. Epoxy is used for corrosion protection as well as adhesion. You cant get corrosion protection from sandpaper. The other potential problem is you over catalized the product. The fact that you had primer left over after using all 4 tubes of hardener tells this clearly. Over catalizing can result in a much slower cure time and can cause other potential long term problems. Please if you are going to teach, be responsible and teach it correctly. I’m sure Evercoat would prefer you teach your viewers the best way to use this primer. Not trying to bust your chops or come across as a know it all, but this is and has been my job for many years. I am a big fan and you have inspired me on my projects. Thank you!

Thats GREAT , you brought back IT's FRIDAAAAYY !!!

Awesome! Great job, Jolene! Chad, you're an excellent teacher 😊

little tip for anyone, if yu wrap the airline around your wrist then over your shoulder it keeps it away from roof and hoods if you are a short arse like me :)

You and your cheap paint guns! I Love it.. goes to show it's not about the tool it's about who is using it.

Nice teamwork! Chad is a great instructor. Always a pleasure to watch you two.

Good job Chad, very informative. Nice to see Jolene in there lending a hand doing the priming.

Excellent videos,glad I took the time to watch.a good refresher education to help me with my projects. Good job the both of you😁👍

You're so informative and thorough with everything you show on your page that not only do I think I can weld, I also think I can spray paint on a car now too! ❤

Spraying is SUCH a great reward for a good prep job ! Pretty too!

Great job guys !!! Just had my truck painted last year. Sure wish I had somebody take pride in there work like you do. I was so Disappointed. Sucks when you are super excited and then get taken by someone who just doesn’t take pride in there craft.

It’s FRIDAY! Looking good all primed up...

I always soak the floor down the moisture helps clear the air.

You guys are doing something great, educational and fun.

Your shop is like my garage. If you had 20 more feet of bench space it would be covered with stuff and you still wouldn't have any room to set a gallon of primer.

Love your videos and lessons,Joleen is terrific what a lucky guy you are Chad !

Great Stuff Chad & Jolene !!! Thank You Both !

Jolene looks good everyday

You talk with theory and practice at the same time. Life make you a teacher.Thanks a lot for your videos , really inspiring and cheerful.Say Hi to Joeline...GBY!

A couple that plays together stays together.....another informative video.....well done guys.

He’s one of the most random thinking people I know but it’s all about the same thing if ya know what I’m saying :) awesome videos and good camera work

Great job Jolene!! Like a pro. Always willing to learn. Can't wait to see the final results. Maybe Jolene gona be spraying the Bugatti. Your a quick study, I'm sure you can do it. Bad Chad is a great teacher..I look forward to watching you guys every day. Always interesting for sure.

Learned a lot Thanks Chad and Jolene fine details are everything

You and your wife are awsome thanks for teaching us, legends.

The buzz of the paint sets in during the second coat as chad goes into a zen quiet mode and enjoys the buzz.

Jolene you did a great job girl don't even think you did anything wrong , but I will say as a painter it is hard to watch someone else paint .LOL I'm wanting put my hand through the phone .Lol and finish painting it myself lol.you do have a great teacher . Listen and learn and you'll be as good as he is very soon. peace out..

Jolene you did a great job with the gun another great video.

Chad and the beautiful Jolene, as people would call her, love your channel and the things that you do. I'm from Texas and a shed tree mechanic. keep up the great work. Love your projects and the way you help others. Keep up the great work.

The Eastwood spec sheet says I can't use Featherfill directly onto bare metal. Do I first need to apply a self etching (or epoxy) primer on bare metal, then apply Featherfill on top of it?

Excellent job Jolene

Great video. The trust and patience that Chad has with Jolene shows his true love for her. It brings joyful tears to one’s eyes to see their love and respect for each other. I am fortunate to have the same with my beautiful wife. Our wishes for the greatest success in your adventures.

Awesome video as usual....I can watch...and watch...and a new build...hot damn!!!

she's a natural and it was great to see you give some coaching tips to teach a novice painter and film. Good switch up. Love the content.

great video.. when you started talking about trying not to spill primer it reminded me of doing that so much...when pouring primer like that and its full.. use some tape and go halfway around the upper part of your can and layer it.. then fold it a bit and run two more tape strips on the outter edges for support.. when you go to pour your primer it will act as one of those old timey oil spickets people used in those old oil cans.. when done and primer is done running back into the can just pull tape off.. just a trick I learned..

I always try to follow all your videos, your work is great.

These videos are awesome! Really pumping me up to get crackin on the bagged '52 Chevy I'm building over on my channel! Can't wait to get to body work!

Hi Chad,. Did you drain the water from the compressor wipe down and clean metal with acetone spray a lite coat of etching primer on metal, and I hope the feather edge does not lift the old finish...happy sanding!!!!!!

You both did a great job. Looks great 👍

Great prime application by both. 😎👍🇨🇦

Love the work you do.

I would recommend some kind of wash primer on the metal

Love watching the process

what a nice job you guys are doing...its going to be great.

Lookin Good. Good job Jolene.

When you are teaching somebody to use the gun you should let them know that you pull the trigger partially and only the air comes out then you pull the trigger more and the paint comes out but when you pull the trigger a little bit you always have are coming out and then when you want the pain to come out you as you're rolling with your hand you pulled the trigger the rest of the way to lift the paint come out and at the end of each stroke you can let off the trigger a little bit to stop the paint flow when you need to

WOW, Looking good...

Chad your a very lucky man who has a wife that shares the same passion as you, cheers to both of you and more couples could should appreciate each other a bit more.

yup' it takes a lot of skill to do it all in one take and keep the audiance engaged well done

I´m learning watching your grate videos. Friday-cheers from Sweden. SKÅL

You promote confidence in yourself to someone… even with the gun comment.. doesnt matter the value of the item your using..its your skill that does the work.. great.

What A Team!!!

Thanks for sharing. Good stuff!

Brilliant- I love it

Love watching your videos

Great teaching video Chad !

Thanks you two! Cheers 🍻

The data sheet for Evercoat Feather fill G2 states it needs to be applied over epoxy primer, not on bare metal.

Thankyou for these videos Chad I'm going to give the windex a try next time I'm topcoating something.

It’s Friday.....great primer job guys.

This car looks phenomenal Chad! Nice to see Jolene in the video as well. 😀

wow so cool,,nice job folks

Nice job jolene did great on the gun one step closer

Hello I was told the evercoat g2 primer wasn’t a direct to metal primer the super build 4 to 1 was

Hi Chad and the beautiful Jolene, greetings from Ireland, absolutely Love your Channel and all your hard work and design skills, about that troublesome earth clamp on the mig welder have you ever considered adding a magnet instead of that crocodile clamp

Good job rock on!

Chad. I would have put etch primer first. I sprayed lots of that primer.

GREAD JOB CHAD; YOU DO GREAT WORK IT IS A PLEASER WATCHING YOU,

G'DAY Chad & Jolene, great work with getting Primer laid down,the only prerequisite before spraying,that we have here in Queensland Australia is the checking and emptying of the water trap/ filter,as with our high humidity, moisture in air compressor and lines is a problem that must be addressed! To take up your challenge to call you out on a build or project,I've got one ,bring back your son Colten,to work to build your dream "CAFE RACER" style Kawasaki Z900 custom bike,to strip,restore and customise and have prepared and ready for paint,alongside the Bugatti,then have matching colour prized toys,as always Kindest Regards Dave McLaughlin Queensland Australia

Jolene you’re a beautiful human being Chad you’re a legend!!! Jolene doesn’t mind getting her hands and clothes dirty and learning the trade!! Chad loves to hand that incredible knowledge on!!! Great couple!!

Jolene is going to make a great painter. I mean it! She has a great form for a beginner and I believe will be a easy student.

Always use the g2, great product

Just like laying shingles painting is just like laying shingles on a roof or a house overlap 👍

Great camera work!

Chad I love the way u got Jolene to prime and mask. Jolene gun more straight down over surface and a little slower and 50% overlap. But u did good girl. Love your videos u 2.

Chad, strange choice, especially when Evercoat's own TDS says not to use this over bare metal surfaces of more than 1 square inch. They say to use this product over epoxy primer on bare metals. I can only think the longevity of the paint will be affected, this being a high solids, sandable primer.

I just subscribed I keep learning stuff watching your videos so I just subscribed.

I love how slow and smooth jolene’s filming is

Smashed it

Quite the thing to be able to say "The first car I painted was a jaguar! "

what an amazing woman you have their Chad ...you are one lucky man

I was getting very nervous watching her but it’s only primer and she’s gorgeous

That exhaust fan must be some kind of color art.

Hi Chad & Jolene, great videos. Your shop is more like the typical working man's garage than anything I've seen on UTUBE. Very educational. Will you give us some pointers on prepping the mid 80's typical deep surface rust bodys with equipment like yours. You prefer acid, sanding, blasting, or other to deal with deep rust pits. HELP ME. Thanks Billy J.

Using Windex just like Fitzee. Great minds think alike.

Great job. Rad shop ! I would love to work there also. A1.

Love the way you work together with your woman

It's FRIDAY,prime that Jag

Would love to see you build a tail dragger

The more you paint Jolene the better you get at it keep up the great work. We need more women auto painter's there's not that many of them. In the automotive industry that is.

I think it would be nice to see how you would build boat tail speedster. I think those cars are 🔥.

I like Chad I like him I THINK HE IS VERY SMART,

Super👍👍👍👍

You should try a H.V.L.P gun .. you'll be surprised how good a finish you can get 🤘🤘

I am starting to get your perspective on polyester primers. If you really wait a long time (2-3 weeks) without heat, no cracking is to be expected.