This is a ball tuning tool for creating spherical knobs such as shift knobs or drill press knobs and even the knob at the end of the tool handle that I made.
Пікірлер: 36
@johnnunes79358 жыл бұрын
Glad you liked the Video. I call it my right of passage project, it was the first big project I tackled, surprisingly it all went as it should. Welder/fabricator/diesel mechanic 46 years now retired.
@brentmcfadden9445 жыл бұрын
Love the build love the tunes Keep on ballin!
@mr265t5 жыл бұрын
Nice work
@wimutfryslan4527 жыл бұрын
nice done !
@AllodialTitle7 жыл бұрын
Nice work..
@baseemalaani20407 жыл бұрын
very very good
@MultiChaga3 жыл бұрын
Nice work John, a very practical tool to have. BUT, I would have loved to see details in mounting it to the lathe carriage just before starting to cut.
@johnnunes79353 жыл бұрын
The tool was made to fit my model lathe. To mount it you take the two fastener off that secure the compound slid remove the compound slide and mount the tool in its place using the two fasteners.
@sking03697 жыл бұрын
That's a catchy tune there.
@harriscreekcentral7 жыл бұрын
To Shrill a whistle - hard on the ears.
@johnnunes79357 жыл бұрын
sking0369 Yes it was all measured out prior to the build and yes you want to be on center.
@everardomike41337 жыл бұрын
muy bueno
@kundankumar69574 жыл бұрын
thanks you sir
@redneckswitwheels7 жыл бұрын
try to shorten how far out ur part is from the chuck.that will help with chatter n improve finish
@trialnterror7 жыл бұрын
I guess my question was your height wouldn't change once it's fixed on the lathe. (I guess you just measured to make sure your on center?) Isn't it important to be on center ?
@DouglasGotardo2 жыл бұрын
👏👏👏🤳
@trialnterror7 жыл бұрын
What about height adjustment? So your on center?
@johnnunes79357 жыл бұрын
trialnterror The ball turner is made for my lathe only. If you wanted hight adjustment you could drill the cutting bar straight down and add two set screws one just behind the up right with the cutters and the other on the opposite end. You also would have to mill off a couple of thousands on the bottom of the cutting bar so you'd have your up and down limits.
@billsuncire79538 жыл бұрын
just found your channel. I am new to machines but do have a 6 "atlas mark2 ,tig, weld and plasma cut. let a logan 2535v get past me last mmonth $1500
@JamesDedmon7 жыл бұрын
Bill Suncire m
@LeandroSilva-uj7qy7 жыл бұрын
muito bom e possivel disponibilizar desnhos pra nós
@jmiddlefinger6 жыл бұрын
Leandro Silva vou traduzir por você que ele entende... "Very nice, is it possible to make the plans available to us?"
@johnnunes79352 жыл бұрын
unfortunately, there are no plans available. When I made this it all came from my head but didn't put anything on paper. Thanks for the interest.
@floriansauer44623 жыл бұрын
it would be great to adjust the hight of that so you wouldnt have the problem with the little knob left over at the front
@johnnunes79353 жыл бұрын
The height is already worked into the build and centered for use on my lathe only. If I would have turned it a little further on the video you would have seen it remove the little tit at the end. Thanks for the feed back.
@josesalanis44483 жыл бұрын
😃💪👏👏👏👏
@marcellonardi82364 жыл бұрын
Scusa, il tuo lavoro, e' ferro o acciaio?
@johnnunes79354 жыл бұрын
Steel
@marcellonardi82364 жыл бұрын
@@johnnunes7935 Tank you
@jimlacharity80586 жыл бұрын
Good looking work but the music sure is annoying.
@dspikes3165 жыл бұрын
you wanna make me one?
@johnnunes79355 жыл бұрын
Sorry but no. Way to many hours involved.
@henkvandijk36686 жыл бұрын
Fraai eenvoudig, MAAR er is geen fijninstelling op de bol dia. Jammer