Basic Lessons Learned with my Precision Matthews PM-25MV.
Пікірлер: 44
@frankk8018 Жыл бұрын
Thanks for taking the time to post that.
@joat_mon Жыл бұрын
Nice overview thanks. I think when I get a lathe it will be a Precision Matthews. Hope to have my mill running again soon.
@ogmaker3 жыл бұрын
Quinn from BlondiHacks recommends a square pipe plug socket for the drawbar.
@tymz-r-achangin Жыл бұрын
Critical safety tip. Dont loose track of how far your moobies stick out. Can get seriously hurt by the cutters
@industrialebikes49564 жыл бұрын
Corrections: (1) I was often referring to the quill as the spindle, and (2) 1/2" T-Slot nuts are too big! I use 7/16" with 3/8"-16 thread T-Slot nuts.
@kenbeane3112 Жыл бұрын
2 flute End Mills are center cutters, and multiple flutes those can be center cutters or non-center cutters
@MachineBucket2 жыл бұрын
Thanks for compiling this information!
@SuperKingslaw3 жыл бұрын
2 flute end mills are better for cutting aluminum than 4 flute. Nice setup!
@incubatork4 жыл бұрын
Your 2 flute mills are better for slotting most materials not just aluminium, now you have a mill the extra Tnuts you bought are excess, you can make your own. Also unless you do a lot of angle work take the swivel off the vice, they are not very accurate or rigid and it will reflect in your finished work.
@industrialebikes49564 жыл бұрын
I have since taken the swivel off of my vise. I am much happier without the swivel.
@sto27797 ай бұрын
In general what would say repeatability tolerance is like for the pm-25mv?
@joewest1972 Жыл бұрын
I just came across your post, I have the same mill, IMO your X feed is too tight. Loosen it, put a piece of paper between the gears, retighten, manually, turn the x axis and roll the paper out from between those gears. Grease the gears and all will be good. Dont keep that x feed that tight
@industrialebikes4956 Жыл бұрын
Great idea
@Zulda72313 жыл бұрын
Good video; thanks!
@Fernanderas20113 жыл бұрын
Thank you for your time in providing all the info., I was planning Grizzly g0704 but , you open my eyes to a better choice, can you please supply the link for the DRO, o insallation for it, I am new to this trade.
@industrialebikes49563 жыл бұрын
www.precisionmatthews.com
@stevedunn44904 жыл бұрын
Awesome video
@carlspencer40243 жыл бұрын
From the sound of the power feed, your gears are to tight. Put a piece of paper between the gears when you tighten the bolts, then rotate the gears to expel the the paper.
@burnsm20122 жыл бұрын
Great video. 1 question. Where do u get your metal stock from?
@jamesbreland21852 жыл бұрын
could you do me a fovor ? could you traverse your machine all the way to the left in the x axis. I need to know when in this position what is the distance from the center of the machine to the outermost point with the power feed installed. I'm trying to find out if I have enough room for the power feed on a pm-25.
@wags97774 жыл бұрын
File or grind when you have a mill?
@BlueBeemerBoy772 жыл бұрын
Thankyou for the video. Are you happy with the size of this machine? Im in the market....
@tano17474 жыл бұрын
I suggest for oiling up under the table on your x axis ways, you need a proper pump type oil can. The plastic squeeze bottle style doesn't push oil when pointing upward. You weren't oiling anything in the video when demonstrating that bit, just blowing air on the ways.
@industrialebikes49564 жыл бұрын
I just got a proper oil can yesterday with my lathe order.
@tano17474 жыл бұрын
@@industrialebikes4956 call that a win then! (Of course some would say it is an expensive way to buy an oil can but whatever works...) Actually you could also tell people you got a free lathe with the oil can you needed to buy for your mill. That would sound much more impressive!
@CarlPugh4 жыл бұрын
Greta video thank you! Who is the other KZfaqr you mentioned that recommended the parallel set?
@JustinAbrahms4 жыл бұрын
kzfaq.info is the person he's talking about.
@euroman120003 жыл бұрын
Does your spindle get hot when milling or running at no load?
@danielgeorge52392 жыл бұрын
How's the rigidity when milling steel?
@nickminderman73802 жыл бұрын
does it come with the dro
@donepearce10 ай бұрын
Metric to Standard? You mean Standard to Inch.
@makosharkcnc77302 жыл бұрын
how did you get so many subs so fast?
@10-4CodyWade Жыл бұрын
This may be a good video but I can't hear a word you're saying bro.
@robertjordon57824 жыл бұрын
How much for this Machine?
@industrialebikes49564 жыл бұрын
Depends on the options (e.g., DRO). Check the Precision Matthews website.
@VikramSingh-hf5il4 жыл бұрын
?
@industrialebikes49564 жыл бұрын
Same price plus shipping to India.
@johnbower87852 жыл бұрын
What's wrong with you people who create videos that you cannot hear! Don't you ever go back and listen to the video.
@johnnyciantar2 жыл бұрын
Soon as you mentioned blondie hacks I had to stop watching.
@F1DesignUS2 жыл бұрын
Yep....that Blondie dude freaks me out!
@silverbackag97908 ай бұрын
Just had a look see. What the fck did I just stumble into? I apparently took a wrong left turn in Albuquerque.