Basic Setup of Hitachi WJ200 Drive

Рет қаралды 95,739

Күн бұрын

Basic Start-Up of Hitachi Drive - WJ200 Series presented by Katie Rydzewski for Galco TV. Buy the items featured in this video at 800-337-1720 or visit: www.galco.com/shop/WJ200-Hitac...
The Hitachi industrial WJ200 Series AC Variable Speed Drives range from 100-200VAC and single phase input to three phase output. The WJ200 Variable Speed Drive comes with an integrated auto-tuning function for easy sensorless vector control that realizes high starting torque of 200% or greater, suitable for a variety of applications.
WJ200 Series Features:
• High starting torque and dramatically improved speed stability with advanced sensorless vector control
• Simplified auto-tuning procedure
• Easy setup and operation via standard integral keypad, optional enhanced keypad or via PC software
• Dynamic braking transistor in all models
• Built in EasySequence (EzSQ) PLC-like functionality
• Simple position control capability
• Capable of driving permanent magnet as well as standard induction motors
• Dual rated for CT/VT applications
• New and more effective trip avoidance functions, safe-stop function
For more Hitachi AC Drives visit: www.galco.com/shop/Hitachi-Ame...
To find more Hitachi Drives go to: www.galco.com/get/Hitachi-Amer...
And for the full line of Hitachi America Products visit: www.galco.com/find/Hitachi-Ame...
Galco is a Factory Authorized Stocking Distributor for Over 150 Brands of Industrial Electrical & Electronic Automation, Controls and Component Products; On-Site and Send-In Repair Services for Industrial Control & Automation Products for Over 2,000 Brands; Engineered Systems Integration, Retrofits & Upgrades for Variable Speed Drives, CNC, PLC Systems, Dynamometers & Test Stand Applications. Visit us online at www.galco.com or call us at 800-337-1720.
www.galco.com/safety
With respect to the usage, installation or assembly of any products described in this video, Galco Industrial Electronics, Inc., a Michigan corporation, encourages you to follow the requirements and/or guidelines of: i) the Occupational Safety and Health Act of 1970, Public Law 91-596, as amended, and all laws, rules and regulations implemented in relation thereto; ii) the National Electric Code®; and iii) NFPA 70E®. Any installation, assembly or work described in this video should be performed by a qualified licensed electrician.
GTV, Galco, galco.com, Galco Industrial Electronics, and Galco Industrial Electronics, Inc. are registered and/or pending registered trademarks under the U.S. Patent and Trademark Office, assumed names, registered domain names, and/or trade names of Galco Industrial Electronics, Inc., a Michigan corporation.
LEGAL DISCLAIMER:
While we have made every attempt to ensure that the information provided is accurate and has been obtained from reliable sources, Galco is not responsible for any errors or omissions, or for the results obtained from the use of this information. All information is provided "as is", with no guarantee of completeness, accuracy, timeliness or of the results obtained from the use of this information, and without warranty of any kind, express or implied, including, but not limited to warrantees of performance, merchantability and fitness for a particular purpose. At all times you should defer to the instructions and safety guidelines issued by the manufacturer. In no event will Galco, its agents or employees thereof be liable to you or anyone else for any decision made or action taken in reliance on the information provided to you or for any consequential, special or similar damages, even if advised of the possibility of such damages.

Пікірлер: 40

@anmed77 2 жыл бұрын

I don’t know if you are still around here but I have to say thanks, you save my life🙏

@stevebausch72 Ай бұрын

Somebody should produce a "For Dummies" book for specific makes/models of VFD. I have this specific VFD, which has been set aside for several years. When I got it, I made pages of annotations. When I pulled it out again (still works), those notes were extremely valuable. The thick little book is incomplete and not perfect. Many of us aren't trying to automate a plant; we aren't trying to have various sensors adjust the motor. We just want a three phase motor to run on single phase. We need the VFD to run, stop, and reverse the motor. Braking might be useful, and variable speed would be icing on the cake. Even real, genuine factories may simply want to run "exactly what we need, but the wrong rpm" motor at 43hz. That horrible manual is truly an act of cruelty. But Hitachi, and other makers, are so proud of three or maybe four ways to control speed, they fail to mention the VFD is essentially locked out when it leaves the factory. Not explicitly mentioned in the printed manual. Oh yeah, the printed manual is not complete, you need to download the PDF... They suggest a crimper to attach ferrules to control wires. That crimper costs more than the VFD! You really do need a ferrule crimper, or maybe not. It seems terminal strip is impossible to access. Oh, I see, the removable access panel is EXACTLY THE SAME COLOR! And the cover that blocks the panel is EXACTLY the same color also! Oh, remove one screw, and, uh, oh, PRY IT OFF? yeah, sort of, it's also snapped on, besides the screw at the bottom right corner. Honestly, why not buy a cheap Chinese VFD and have exactly the same frustration for much less money? Or... Why not produce a simple VFD, and SPEND MONEY ON MAKING A COMPREHENSIBLE INSTALLATION MANUAL?

@scottvance74 7 жыл бұрын

Thanks for this informative video. Another parameter which one might want to change is B083 (carrier frequency). The default value (2 KHz) allows for maximum power, but in my case caused the motor to have an annoying hum. Raising this value to about 10 KHz allows for a quieter/smoother running system if you have the system sized so that it's not maxed out on your motor.

@riyadrahman9844 3 жыл бұрын

thanks

@juelz111 2 жыл бұрын

hello i have 208v 3 phase input voltage, would you recommend setting the drives input voltage setting to 200 or 215v?

@leveluptactic8456 3 жыл бұрын

the switch to skip the run command... does anyone know how to wire it up? or where i can find it in the manual? btw great tutorial video

@Raviranjankumar-jf6js 3 жыл бұрын

I have 3phase this same wj200 VFD ..how to attach a potaionmeter to control the moter speed and what are the parameter need to set ??? Plz help

@rafaelperez5184 3 жыл бұрын

Hello, can the engine rpm be displayed in the vfd?

@farrag68ify 7 жыл бұрын

Hi, what is the voltage increase method? I havea Device a 220 and a Hz-58 and a output power 180-volt

@D6251110H 3 жыл бұрын

You need a unit that matches your input/output parameters. For example. I have 120V power input in single phase. To run a 3 phase motor in 220V I selected a VFD that matches this requirement in the specifications.

@mrsnrub3712 5 жыл бұрын

Does anyone have insight on the Analog Output functions? Specifically C028 = 02, Inverter Output Torque. The PDF manual section 4-90 only mentions 0-10VDC range, but does not specify units or scale.

@GalcoIndustrial 5 жыл бұрын

The scale is based on the amp rating of the drive.

@mrsnrub3712 5 жыл бұрын

Thanks for your prompt reply. I have a WJ200-015SJ, per section 1-4 this is rated at 8.0A at CT (which was the default value in parameter B012). I changed this to correspond to my motor nameplate (6.0A). Does this change the scaling of the analog output accordingly? I assume what the drive is actually doing is reading Volts and Amps and trying to correspond that power draw to motor output torque? Also, what are the units for Output Torque? (N-m I would assume being a Japanese drive, but maybe its Ft-lbs or ?)

@certifiedbrokanic 5 жыл бұрын

I have a remote 3 wire 'start/stop/emergency stop' box. Where do i wire this and what parameter do i change?

@Dambody 6 жыл бұрын

Hello! Can any body tell me how should I use wj200-075hf with 15hp motor? what settings should I change?

@GalcoIndustrial 6 жыл бұрын

Usually you start with the motor name plate values, VOLTS, Hertz, RPM etc. Then set your MAX and MIN speed, then ACCEL/DECEL. This should get you in the ball park so to speak. What kind of application is it?

@farrag68ify 7 жыл бұрын

I have the same device on the solar energy, if the frequency of the constant control manual only, how the method of making the frequency is automatic so that if the electricity goes down the device decreases frequency and does not stop the device and thank you

@GalcoIndustrial 7 жыл бұрын

Try asking again differently your phrase makes no sense. Are you asking how Volts to Hertz works?

@GalcoIndustrial 7 жыл бұрын

Wait a minute, when you say the Electricity are you referring to the input power?Are you asking about "Power Loss Ride Thru"

@farrag68ify 7 жыл бұрын

GalcoTV The device I have input from solar energy The device has a manual frequency, for example 55 Hz, and if the sun is weak (for example, there are light clouds) the device stops working ,,, and my friend has the same device; the frequency is automatic (if the light of solar energy, the frequency of down to 40 Hz) What is the way to make the frequency automatic? Thank you

@GalcoIndustrial 7 жыл бұрын

The output Frequency of the WJ200 is regulated based on speed command input to the drive, you just set it to what you need.

@farrag68ify 7 жыл бұрын

GalcoTV Meaning it can not be made automatic?

@jfcustomfab 3 жыл бұрын

F001 is very important it comes as 000 .. but needs to ramped up to run the motor .. I don’t know why the default is 00

@Raviranjankumar-jf6js 3 жыл бұрын

Can someone give me all required parameters for 3 phase same VFD ?????

@stevebausch72 Ай бұрын

Okay, you are truly ignorant of VFD operation. But Hitachi isn't helping either. Anyone wanting a VFD installed needs to volunteer some information: Motor needs variable frequency? Or fixed at 60 or 50 Hz? Or fixed at some other frequency? Or is frequency controlled by sensors and automation? Is there a need for bidirectional operation? Controlled by machine operator or automation? And when the VFD programming is perfect and complete, WRITE IT DOWN.

@JoseCastillo-ug9hw 5 жыл бұрын

Por favor quien lo consiguió en español?

@Raviranjankumar-jf6js 3 жыл бұрын

VFD parameter ??? Plz

@hazwankhalid838 10 ай бұрын

Hi is it the motor only can be run after all those setup?

@stevebausch72 Ай бұрын

Yes, the VFD is an expensive brick when removed from the box.

@agustin4764 8 жыл бұрын

deverial acer un tutorial de usuario en español

@juliowolf7846 7 жыл бұрын

agustin De Luna eso es superación aprende este idioma se mejor

@manutpunpook9197 10 жыл бұрын

I love you

@Raviranjankumar-jf6js 3 жыл бұрын

I need urgently plz some one ??

@brewtalityk 5 жыл бұрын

This doesnt explain how to autotune. I've set H001 but it doesnt auto-tune

@GalcoIndustrial 5 жыл бұрын

You might make sure that parameter B037=0 and try to auto tune again

@steveeber2324 Жыл бұрын

This would be a lot more useful and easier to follow if you were to first give some kind of clue as to how the keypad operates. The manual does this very poorly as well. I've been struggeling for hours trying to figure out just how to change other parameters. There seems to be no logic to the keys.