No video
BC Racing Coilover Installation - 90-97 Honda Accord
Рет қаралды 20,037
Күн бұрынThe day has finally come where Project CB9 gets a set of custom made BC Racing Extreme Low coilovers. I'll go over the old suspension removal process along with the steps needed to install the new coilovers on a 1990-1997 Honda Accord (CB7, CB9, CD7, CD9). Its time more more low and better handling for Project CB9 build!
#4thgenaccord #hondaaccord #accord #cb7 #cb9 #CD7 #cd9 #coilovers #bcracing
@norm5431 4 ай бұрын
Thank you for this vid. This is what I needed to refresh my mind. My TEIN’s were leaking and would not pass a “safety check” 🙃 Very good video👏🏽👏🏽👏🏽👏🏽🤙🏽🍍🍍🍍🍍
@georgenaranjo8852 Жыл бұрын
Love the videos! Can't wait to see how this thing turns out. Happy holidays!
@Gabe-tt2jj Жыл бұрын
your awesome man, you give me lots of inspiration for my own accord. Much love from Jersey
@canadianbluepants9446 11 ай бұрын
i cant believe i have just found you, i bought a cb9 a few weeks ago as my first car and ive been wondering how to do this and that and you have the answers to all of it, amazing (i may also be jealous of that blue since cb9s are super rare here)
@overwatch1385 10 ай бұрын
I reviewed your video prior to lowering my cb7 coupe. Thank you 👍👍
@_20nine_ Жыл бұрын
Getting my 92' LX coupe back up and running, thanks for the help bro
@CALLIN799 Жыл бұрын
Like the accord! 5 lug that's awesome!
@Rogg33k 5 ай бұрын
Awesome thank you best video
@ZacVaper 2 ай бұрын
Pictures of the cars on it's wheels, before and after, would have been the thing to do....
@machocalderon4042 Жыл бұрын
Nice job made it look eze
@accord_aero_r Жыл бұрын
Did you use anti-seize putting that rear lower strut bolt back in? I'd do that on all exterior bolts, but the rear suspension bolts in particular seem to be super susceptible to rust. Both my toe bolts and my lower strut bolts had to be cut off of my car because they were seized into the bushing sleeves. I was so jealous to see yours zipped right out when taking out the stock struts. Can't wait to see this on the ground with the wheels!
@randomrebuilds Жыл бұрын
No but guess it wouldn’t hurt to do so. Fortunately this is a FL car so rust hasn’t been an issue for me.
@IsaacSanchez-y4j 5 күн бұрын
I have a question i was wondering what kind of rear upper control arm you have i have a 1990 honda accord cb7 and the rear upper control arm slapped in half my car is low and im not sure what kind to buy
@randomrebuilds 5 күн бұрын
@@IsaacSanchez-y4j I installed SPC rear adjustable UCAs. Part #67265
@gabe70hb Жыл бұрын
Doing the lords work! I went with the same coilovers, but opted for the regular springs. Also in the process of gathering all the parts to 5 speed swap on my 91 CB7. What did you set your dampening to? I set mine halfway between hard/soft for now, but noticed the rear is bouncing a little bit more
@trackshun 8 ай бұрын
In my experience on the CB7 and my FG4, I would set my rears to hogher dampening than the front. The stiffer the rear is on a fwd, the better for overall handling. I’ve tried it the other way around, I’ve tried front and rear at 16 on a 32 & 33 way adjustable, the car just oversteers. So set rear to more damp than the front. And gradually drive and test your car to set it just right.
@pedrososa26 4 ай бұрын
How low is the front bro ?
@vintagegear5240 Жыл бұрын
Honda told me that the car is too old and they might not be able to diagnose/ fix my issue. My car leans to the driver side by an inch . What’s your opinion on that? It also made metal riddle noises as I went up slopes. I put air into it and I don’t hear the rattling anymore much but it leans
@randomrebuilds Жыл бұрын
The driver front side leans more than the passenger front due to the engine weight and placement being heavier towards the drivers side. Coilovers with height adjusted or pre-load adjustment will fix that issue and level the car out with your settings.
@vintagegear5240 Жыл бұрын
@@randomrebuilds I weigh 250 lbs. what are the odds that my fat is causing the issue? There are times that I guess that I have just noticed it blatantly . Would the coilovers and height adjustment be able to be done to factory spec? Are coilovers a replacement for the spring? So the whole cylinder/vertical rod/ spring /strut , whatever you’d call it would need to be replaced ? Also curious on the likelihood of finding the right sized coilovers if it is possible for an older car
@isaihsalas7412 Жыл бұрын
Is that an f20c? If so that's sick af!
@randomrebuilds Жыл бұрын
H22A
@isaihsalas7412 Жыл бұрын
@@randomrebuilds ok ok under appreciated engine! I kike it!
@doclockwood8809 Жыл бұрын
Great videos. Any videos on how to service/urethane fill/fix/replace the rear engine mount on my '92 Cb9? Thanks, and happy holidaze! Hondas Rule!
@Miguel-dl3pp Жыл бұрын
do the coils still fit after doing a 5lug swap using the ody knuckles upfront
@trackshun 8 ай бұрын
Coilovers are connected to the lower control arms. They fit no issue.
@Miguel-dl3pp 8 ай бұрын
@@trackshunthanks havent even done the swap yet
@rutenmedita4686 Жыл бұрын
Can't wait to see the wheels. Got same car sedan
The Honda Resource
Рет қаралды 14 М.