I transform a chunk of pure gold into a masterpiece. Watch the 24 karat magic. gold jewellery making gold ring design making gold ring
Пікірлер: 36
@lamp7432 Жыл бұрын
That surely is a very manly, beefy, brawny ring. I'm sure the client loves it!
@kirtandrews185911 күн бұрын
That is frigging awesome I absolutely love it. I had no way you could melt down those single ingots. I have a powerful butane torch wirh small flame outlet. I have seen other jewellers use it. Do you think it would work? 24k is soft as can be. I can't get over how you made that. It is so impressive. From a local jewellers here £900 easy for a single 5gram 24kbgold ingot £300 what a saving
@thomasgarcia9445 Жыл бұрын
If you want to remove the taper that comes from forming it on the mandrel, you can size up that last size by hammering it on a socket instead of a mandrel. The trick is to have the ring a smidge smaller than the socket and then hammer the socket through the inside of the ring. The chamfer on the socket and the taper inside the ring make this operation possible. Then hold the socket in a vise with the ring around it and hammer to size just as you'd do with a mandrel.
@mangledtapes Жыл бұрын
welcome back! hope to see more vids in the future
@EroticOnion237 сағат бұрын
I also found that fusing is a butt-clencher for sure 😆, though far preferable than using solder and 'contaminating' a pure piece imo!! EDIT: BTW I found that sticking a wad of ceramic-wool through the middle of the ring makes it 'safer' to heat from the outside, gives it support so it doesn't collapse
@gabrielabissinger6263 Жыл бұрын
Great to see you again!!! I missed your videos!!!
@mustachemetalworks Жыл бұрын
Thanks for the warm welcome back! I've been busy making other big things happen, and my videos had to take the back seat.
@madhavkoppararajeev4829 Жыл бұрын
That was awesome!
@skyelee9398Ай бұрын
Awesome job. Thanks for sharing
@DesertTuna Жыл бұрын
That is a very very nice ring well done 👍
@ssewwess2700 Жыл бұрын
This is so satisfying.
@user-lc2ho8mt5j5 ай бұрын
Sir help me I need a gold planner iron I like that work if available in ur shop how much
@Sporkball Жыл бұрын
Your father is one of my teachers he is fun
@Atmospheric23 Жыл бұрын
Have you tried a liquid flux to fuse the 24k gold? Great video, thanks!
@mustachemetalworks Жыл бұрын
GIVEN: My understanding of flux is that it is used to quell the formation of oxidation and other atmospheric gases interactions with metals that are being heated. When the heated flux shields the metal, it prevents these contaminations that would otherwise jeopardize the structural integrity of the "joint". GIVEN: Gold doesn't interact with any atmospheric gases, even in the liquid phase. THEREFORE: No need to use a flux with fusing 24k gold.
@user-yk1rc6ty2q3 ай бұрын
Beautiful
@mustachemetalworks2 ай бұрын
thank you!
@hasfafamily2 ай бұрын
Semangat beraktifitas sahabat baik, itu pekerjaan yang membutuhkan kesabaran ektra.. 👍👍
@user-lc2ho8mt5j5 ай бұрын
Iron gold plainer sir to order about that tools
@andreak0019 ай бұрын
That gold looks good enough to eat!
@mustachemetalworks9 ай бұрын
I've tried to nibble it but my friend slapped me because it was still on his hand.
@alextucker86242 ай бұрын
What’s a good site to buy all the equipment? I need to mount gold and silver and molds to make jewelry?
@mustachemetalworks2 ай бұрын
Try RioGrande and Amazon
@alextucker86242 ай бұрын
@@mustachemetalworks thank you
@UcheFiasco Жыл бұрын
You’re the only person I’ve seen use 24k to fuse at the end. Anyone know why jewelers use lower karat gold to fuse?
@mustachemetalworks Жыл бұрын
Using the "base" metal (in this case: 24k gold) is the only way to "fuse". Using a lower karat gold, which probably has a lower melting point, is technically a solder, because the base metal now has a lower karat solder in-between the two sides. A real "fused joint" requires the base metal to melt and solidify with only the base metal. I use 24k dust and chips to add extra metal to the joint but I technically don't need to. I could just let the two ends melt and solidify. Using the beneficial melting properties of a lower karat gold is cheating if advertised as a "fused joint"
@keivkeiv Жыл бұрын
What is the surface you melt the gold on? Thank you
@mustachemetalworks Жыл бұрын
Charcoal block. Theoretically... pure carbon. Low coefficient of thermal conductivity. Wet with water to prevent combustion. Re-wet after every flame. I dug a hole to allow the gold to sit in without risking a mess!
@keivkeiv Жыл бұрын
@@mustachemetalworks Thank you! Can you melt gold on top of a clean anvil?
@mustachemetalworks Жыл бұрын
Trust me, that's not a good idea. The anvil will soak up the torch heat and you'll end up with a hot anvil and a warm piece of gold.
@TheRottenOneRepents Жыл бұрын
Did You Just Fart At 24:05?
@TheRottenOneRepents Жыл бұрын
Yeah We Got A Toot.
@mustachemetalworks Жыл бұрын
Ya bois gotta toot sometimes
@wimkoens67803 ай бұрын
This is pure mess work that a child can do even better
@mustachemetalworks3 ай бұрын
Yes! What a terrible mess. Where were the children during quality control? Who allowed this work to see the light of day?