Best Fender Delete for Vulcan 650 S - Installation of Chrome Glow LED Fender Eliminator Tail Tidy

No video

Best Fender Delete for Vulcan 650 S - Installation of Chrome Glow LED Fender Eliminator Tail Tidy

Рет қаралды 78,496

3 жыл бұрын

#Vulcan650s #Kawasaki #Fenderdelete #Chromeglow #Tailtidy #howto #DIY
👇 SUBSCRIBE NOW 👇
/ @kamdorian
🎁SCROLL DOWN FOR LINKS TO BUY THE MODS AND MORE VIDEOS 🎁
🎁BUY THE MODS!!!!🎁
👇Buy CS Racing Exhaust with 5% DISCOUNT👇
csracingusa.co...
👇10% Discount on Quadlock👇
quadlock.refr.c...
👇Buy Kuryakyn Floorboards👇
amzn.to/3ki311o
👇Buy Adapters for Floorboards👇
amzn.to/3ZJeyam
👇Buy Bar End Mirrors👇
amzn.to/3ZNjU4A
👇Buy Clutch and Brake Levers👇
amzn.to/3XEjax7
👇Buy Radiator Grill Cover👇
amzn.to/3qQRB8d
👇Buy Chrome Glow Fender Delete Taillight👇
amzn.to/3kpxuL6
👇Buy LED Headlight👇
amzn.to/3km9TuN
👇Buy LED Flasher Relay to fix hyperflash👇
amzn.to/3CYfz4w
👇Buy Quad Lock Phone Mount PRO👇
amzn.to/3ZGqJox
👇Buy Quad Lock Phone Mount👇
amzn.to/3CYdXrB
👇Buy Quad Lock Vibration Dampener👇
amzn.to/3kqqzBk
👇Buy Atlas Cruise Control👇
amzn.to/3ki4GUG
Thank you for supporting the channel! As an Amazon Associate I earn from qualifying purchases.
In this video I go over the step by step process to remove the current fender from my 2017 Kawasaki Vulcan 650 S and install the Chrome Glow Fender Eliminator LED light. This totally changes the look of the bike and gives it a much more aggressive feel. The LED light includes a red running light, brake lights, yellow turn signals, license plate light, and hazard lights. I am using the clear LED option but Chrome Glow also sells a smoked light version (not sure if this impacts visibility of the light so I went with the clear option). Links to order this light are below.
The installation is fairly easy just follow the steps and take your time. The hardest part is aligning the LED light bracket to sit perfectly flush with the rear fender, trial and error is needed. The kit includes everything you need: LED tail light, brackets, posi-tap connectors, zip-ties, reflectors for the license plate, and easy to follow instructions.
Towards the end of the video I show the light in action in daylight along with some exhaust notes from my bike! Also a sneak-peak at the next mod install on my bike!
🎁MORE Vulcan 650 VIDEOS!🎁
👇LED Headlight Turn Signal Integration👇
• Best LED Headlight for...
👇LED Headlight Install Video👇
• Best LED Headlight for...
👇Fender Delete Taillight Install Video👇
• Best Fender Delete for...
👇Quadlock Install and Review👇
• Best Phone Mount for M...
👇Bar End Mirrors and Levers Review👇
• Best Bar End Mirrors a...
👇Bar End Mirror Install Video👇
• How to Install Bar End...
👇Brake and Clutch Lever Install Video👇
• How to Install Best Br...
👇Vulcan 650 Riding and Meeting Motovlog👇
• Vulcan 650 S Riding Mo...
👇Atlas Throttle Lock Cruise Control Review Video👇
• Best Cruise Control fo...
👇CS Racing Aftermarket Exhaust Sound👇
• Best Aftermarket Exhau...
👇Vulcan 650 S Riding Motovlog👇
• Vulcan 650 S Riding Mo...
👇Radiator Grill Cover Install Video👇
• Best Radiator Grill fo...
👇Kuryakyn Floor Board Install Video👇
• Best Foot Pegs Floorbo...
Thanks for watching!
Follow me on Instagram @kamdorian
Hit the LIKE button and SUBSCRIBE!!

Пікірлер: 263

@izzojoseph2 3 жыл бұрын

To help prevent confusion of what wire connects where, before disconnect, write the connection on masking tape and tape it to the side that stays (LB for left blinker, etc)

@Kamdorian 3 жыл бұрын

Great idea!

@silverwess 2 жыл бұрын

I have the Corbin seat best purchase so far

@Kamdorian 2 жыл бұрын

I have heard great things about it. The price tag is not great though lol

@forrestnome9521 2 ай бұрын

Corbin seems to be the only seat manufacturer that offers all 3 sizes of seat where the Mustang is a one size fits all.

@Chris64France 2 ай бұрын

Far better than before. Good job!

@Kamdorian 2 ай бұрын

Thank you!

@maggierivera5510 3 жыл бұрын

Love it it’s so much better then the other lights, nice job

@Kamdorian 3 жыл бұрын

I love it too, thank you!!

@motogoondocks3896 3 жыл бұрын

Those 3 bolts were absolutely horrible to remove. I used heat and wd40 and eventually had to get my grinder out because I stripped one real bad. Anyway I bought a kit off ebay which is a knock off of the chrome one but for half the price. Looks great and wish I did this mod months ago. Keep up with the vids and yes those wire caps are awesome!

@Kamdorian 3 жыл бұрын

Haha yea real pain in the butt, cool that you found a cheaper one that works great. Thanks for the feedback I appreciate it!

@brainzy Жыл бұрын

been trying to find a knock off version on ebay but still not come across one

@ashleybest1857 11 ай бұрын

I had no problem with 3 bolts once I gave them a proper 3 minute blast with a heat gun.

@PaulsMotoZen 3 жыл бұрын

Looking forward to seeing more videos about your motorcycles. Take care, ride safe.

@Kamdorian 3 жыл бұрын

Many more videos to come on my SG250 and the Vulcan! Thanks for the sub bud

@Toughbiscuit_ 5 ай бұрын

Kinda funny, this popped up for me a week after I picked up my 650s, and this is the mod the previous owner did

@Kamdorian 5 ай бұрын

Lol nice this mod definitely improves the look of the bike and one less thing for you to change yourself. Congrats on the bike! You planning any mods?

@thehandoftruthsdevoutfollo1386 2 жыл бұрын

Video was a little dark and hard to see at some points but very well explained, enough so that the bits I couldn’t see I was still able to do just by listening. Thanks for the help mate :)

@Kamdorian 2 жыл бұрын

Sorry about that yea could have had better lighting in my garage. Glad it worked out though! Let me know if you have any questions. Ride safe bro!

@alvaropena1220 2 жыл бұрын

You needed the heat gun?

@Kamdorian 2 жыл бұрын

@@alvaropena1220 yes heat gun helped alot to loosen the loctite on the bolts.

@RodrigoMerli 9 ай бұрын

Olá! Também retirei a "rabeta" da minha Vulcan 650. Coloquei outro tipo de suporte de placa e um kit de sinalização em fita led. De fato, ao montar novamente a moto, fica belíssima apenas com o banco do piloto. Parabéns pelo vídeo! Bem detalhado!

@Kamdorian 8 ай бұрын

thank you! which suporte de placa did you use? I want to change the placa location too. Ride safe my friend!

@Ginofox77 3 жыл бұрын

Very nice setup! I have the same exact setup; however, I went with the smoked option. Also, I’d be weary of the plastic they used. Somehow mine cracked (luckily I didn’t lose my plate). Going to JB weld the piece that came off, back on. Fingers crossed it works.

@Kamdorian 3 жыл бұрын

Thanks yea I love the look of it. The plastic felt pretty strong on mine, maybe chrome glow upgraded it after some customer complaints? I'll keep an eye on it hopefully doesn't break. Do you feel the smoked option is not bright enough for people to see you from behind?

@Ginofox77 3 жыл бұрын

@@Kamdorian Yeah man-I was quite sad lol. If CG did, I might have to upgrade mine. Likewise, the smoked option is very light on the smoke (which I prefer.) I’ve actually uploaded a video of my bike a day or two ago, it finally proceeded and should be up on my channel if you want to see the smoked option!

@Kamdorian 3 жыл бұрын

@@Ginofox77 I watched the video, the front blinkers look great I might get them. Also how is the vibration when riding on the bar end mirrors? Were they easy to install?

@Ginofox77 3 жыл бұрын

@@Kamdorian The vibration is somewhat there at higher speeds; however, at lower speeds it’s not present. As for the installation, the bar ends were a breeze to install. They not only look great but function awesome on the road with minimal vibration, as compared to the OE mirrors which in my opinion, are terrible.

@Kamdorian 3 жыл бұрын

@@Ginofox77 awesome I think I'll try them, where did you get the bar end mirrors?

@johnhsmith8566 3 жыл бұрын

Really well done !

@Kamdorian 3 жыл бұрын

Thank you!

@notoriouscowboy9773 2 жыл бұрын

👍 That my friend is now a bobber ...i would have the license plate on the side not behind the tire it would look more better

@Kamdorian 2 жыл бұрын

I agree!! I am looking for a side mount. If you know of one that fits the Vulcan 650 let me know.

@notoriouscowboy9773 2 жыл бұрын

@@Kamdorian Ebay and just type side mount license plate.I have two ..one for each of my bikes.If u look up bobbers u will see most have the side license plate ..Cut the license plate part off your and just leave the brake light part and more of your tire can be seen.

@Kamdorian 2 жыл бұрын

@@notoriouscowboy9773 awesome thanks man I'll get one soon? Excited to see more of the rear tire. I also want to get a 180 or 190 size rear tire next time I need new tires.

@notoriouscowboy9773 2 жыл бұрын

@@Kamdorian right max out that back tire size..looks better and it seems like it better grip ..a skinner tire is light but that back tire is heavier and more contact to the ground

@TechAndMotorcycles Жыл бұрын

Great video, I will probably look into it once I sell my current bike and pick up a Vulcan. But side note I hate posi taps with a passion. They can fail, vibrate loose, or get an intermittent connection. Just solder connection,. It seems intimidating but it's really not

@Kamdorian Жыл бұрын

Thanks man. Yea I would prefer soldering too and I'm sure it's easy I just don't have the soldering equipment. My positaps are working fine so far, fingers crossed they don't fail soon!

@TechAndMotorcycles Жыл бұрын

@@Kamdorian no they do last for awhile and depending on where you are you might be safe. I live in the northwest so corrosion and water are huge things. Also if you want a cheap solder on Amazon is like $20 and risen core solder is like $5. But again you may be perfectly safe. If you do decide to switch your first few times it will work fine but probably look ugly while you learn lol. So just make sure it's in a hidden area🤣

@Kamdorian Жыл бұрын

@@TechAndMotorcycles haha thanks for the info I'll check it out...always wanted to learn soldering.

@Alexrody1 2 жыл бұрын

If the led strip was an inch thicker it’d be nice.. no visibility

@Kamdorian 2 жыл бұрын

Yea I might get one of those rear facing led lights that go on the helmet and signal when braking.

@iyrinenoch9451 2 жыл бұрын

Just picked up the SteelMate led helmet brake light on Amazon Thing is mint for the price!

@forrestnome9521 2 ай бұрын

I have the same one and it's highly visible much more than the OEM. Real life vs video. Super bright at night.

@marvinsolano2484 3 жыл бұрын

Great video! Looking forward for new ones 😊

@Kamdorian 3 жыл бұрын

Thank you! Many more videos on the way!!

@izzojoseph2 3 жыл бұрын

Damn dude, your bike is a bad ass Vulcan! Very close to what I’m working towards. Love this mod! What’s your exhaust?

@Kamdorian 3 жыл бұрын

Thanks man I love the look! It's a CS racing exhaust. Use this link for 5% discount csracingusa.com/discount/KAMDORIAN

@ed.t.hansen6499 Жыл бұрын

Keep fenders on for sure

@johnny_vngel5699 3 жыл бұрын

Sick man! Dope mod

@Kamdorian 3 жыл бұрын

Thanks bro I'm loving it!

@ghostrider852 9 ай бұрын

Love the video bro, but notice how your hazards blink slower than your left/right indicator? You need to add a resistor to the indicator wire so they blink at normal speed.

@Kamdorian 9 ай бұрын

Thanks bro, yea I bought a flash relay just haven't installed yet. Def need it to get rid of the hyper flash

@scott330 7 ай бұрын

@@KamdorianI’m seeing both a resistor and a relay on chrome glows site. Did you need both to slow the flashing down?

@Kamdorian 7 ай бұрын

@@scott330 I bought the flash relay from Amazon. Here's the link amzn.to/3TR2GCD

@scott330 7 ай бұрын

@@Kamdorian awesome, thanks so much!

@nekotherion7317 2 жыл бұрын

I would invest in some crimpers, a ts80 soldering iron, and some connector grab bags, and heatshrink w/ wire wrap of the same kind the vulcan s uses, easy work, looks factory, retains factory insulation and harness condition, if you ever want to sell your bike, those posi-taps will make folks run for the hills...

@Kamdorian 2 жыл бұрын

Ahh good to know yea I do want to make the wiring more professional and permanent. Will work on it one day, thanks for the tips!

@nekotherion7317 2 жыл бұрын

@@Kamdorian Glad it helps :) ive done rewire on various bikes using this method, where folks had basically took scissors to the entire harness, number 1 comment after is "That looks factory", so shows a degree of professionalism, and pride in your ride, and if done well, helps reduce connection corrosion, which with positaps could work its way into the factory wiring harness, and cause early failure, or if a positap ever broke, prevents a short circuit, and as some mods for motorcycles dont use UV rated wiring insulation, UV/marine rated heatshrink, makes the work last a long time :) Should be able to get it all on amazon, if ya have discord or something i can show ya some of the stuff ive used

@nekotherion7317 2 жыл бұрын

@@Kamdorian a haynes/clymer/kawasaki service manual helps too, as your likely to get a full wiring diagram, with wire colors, and other hints n tips

@Kamdorian 2 жыл бұрын

@@nekotherion7317 awesome I'll check it out! Thanks again.

@Kamdorian 2 жыл бұрын

@@nekotherion7317 I never thought of that stuff in terms of corrosion. I never ride in the rain and do waterless washing when I clean the bike. I totally agree, it looks and feel better when it's a more professional wiring job. Looking forward to learning more about it!

@tmtv2234 3 жыл бұрын

very good instructions and helpful! i keep checking online they dont have it in stock :(

@Kamdorian 3 жыл бұрын

Thank you! Check my amazon link in the video description. Otherwise also check the direct chrome glow website.

@tonyb7956 4 ай бұрын

How’s the tail tidy holding up? Lights still work and everything?

@Kamdorian 4 ай бұрын

Holding strong no issues. Lights working and all

@skarpy24 Ай бұрын

I know this might be a silly question, but are the turn signals clearly visible during a sunny day? I might be wrong, but first of all, such an unusual type of light might not catch drivers' attention. Secondly, it might not be very visible in sunlight. Especially since the red light does not disappear when turning. The colors might blend. Am I wrong?

@Jett21887 Жыл бұрын

I hope the led were a little bigger for people from the rear to really see at daytime

@Kamdorian Жыл бұрын

Yea would be cool if it was a double or triple row of LEDs, so far haven't had issues with people seeing me but of course more brightness is always better

@ashleybest1857 11 ай бұрын

The clip you broke is easily avoided if you push in the center button first. They're called plastic rivets

@Kamdorian 11 ай бұрын

Yea I know..the clip on mine was already half broken so it fully broke with little force

@joshc5658 3 жыл бұрын

This is a must have modification! Are the turn signals easy to see?

@Kamdorian 3 жыл бұрын

Yes pretty easy to see. They are definitely not as visible as the stock turn signals but I think they are good enough and I have had no problems with people not seeing me. Also the taillight looks amazing!

@z1v4 3 жыл бұрын

I can read you got the relay kit installed from Kawasaki. How come your blinkers goes too fast then? It's only hasard light that's normal speed. And cool video, it's a nice help. :)

@Kamdorian 3 жыл бұрын

Yea I am not sure why the blinkers are still going fast, I have to check it out. I appreciate the feedback, glad you enjoyed the video!

@z1v4 3 жыл бұрын

@@Kamdorian And nice car too, same as mine in same color. :)

@Kamdorian 3 жыл бұрын

@@z1v4 thanks, I love blue everything haha and of course black!

@forrestnome9521 2 ай бұрын

You need to install the flash relay under the left side of the gas tank.

@cdk_100 4 ай бұрын

hey! looking to grab this for my 23 vulcan s, just wondering have you had any issues with being pulled over for it or any problems with the police?

@Kamdorian 4 ай бұрын

No problems at all. Never got pulled over. It works great! You will love it good luck and ride safe!!

@will-i-amT63 3 ай бұрын

Hey kam love that look , can you add the link for the sissy bar, and thank u bro.

@Kamdorian 3 ай бұрын

Thanks man here's the link. Good luck and ride safe! amzn.to/3WBzdOk

@will-i-amT63 3 ай бұрын

Thanks the eliminator is out of stock great video 👍💯

@vicemkii8688 6 ай бұрын

Do you know by chance if I can put the same fender delete for the Kawasaki Eliminator 450?

@Kamdorian 6 ай бұрын

Sorry I am not sure. If the fender body and mounting holes are the same then it should work fine.

@TrilobitesRTasty 2 жыл бұрын

Do folks know if there is an aftermarket bracket that allows the rear license plate to be attached to the left of the tire? (...like on a V-Rod) Or, would a person need to design a DIY bracket...and cut off the rear license plate frame?

@Kamdorian 2 жыл бұрын

I am actually looking for the same thing. A quick aftermarket part that allows the plate to be mounted on the swingarm left of the tire. I have seen many Vulcans with the side mounting so it's definitely possible. I'll try finding the mounting bracket and send you the link!

@TrilobitesRTasty 2 жыл бұрын

@@Kamdorian That's great! It's good news that an option may exist. Thank you!

@brotherbread6549 3 жыл бұрын

Perfect video brother. What exhaust is that? Thanks again for the vid!

@Kamdorian 3 жыл бұрын

Thanks bud, it's a CS racing exhaust. csracingusa.com/products/kawasaki-vulcan-s-en650-2015-on-full-exhaust-system-muffler-header-cs-racing

@joshc5658 3 жыл бұрын

Check out CS racing and talk to Patrik! He is great to work with and the exhaust sounds awesome 👌

@hectorshouse7348 9 ай бұрын

Nice video…great job😃👍

@Kamdorian 9 ай бұрын

Thank you my man!

@rickytsuha4020 13 күн бұрын

How did you make the yellow lights not pulse so fast and have a lower speed?

@Kamdorian 12 күн бұрын

@@rickytsuha4020 get a flash relay from Amazon amzn.to/4fxmALm

@rickytsuha4020 8 күн бұрын

@@Kamdorian where on the motorcycle does it connect?

@Kamdorian 4 күн бұрын

@@rickytsuha4020 you have to lift the gas tank. There is a connector in between gas tank and base of handle bars. Search KZfaq for Vulcan flash relay install and you will find few videos. Good luck!

@rickytsuha4020 4 күн бұрын

@@Kamdorian thanks bro 🙏

@Ramibiker2023chief Жыл бұрын

Can you mount the plate on the side

@Kamdorian Жыл бұрын

No this kit doesn't come with a mount for the side. You would have to get a different plate mount for that. If you find one let me know!

@Ramibiker2023chief Жыл бұрын

@@Kamdorian google it. Plenty of examples. I think it’s a sharper look personally

@forrestnome9521 2 ай бұрын

Yes you can mount the plate on the side. You have to make sure the mount comes w a plate light and has to be 12" off of the ground to be legal in some states. You would then also cut off the plate holder bracket on the Tail Tidy to make a cleaner look.

@bfrgjufr 3 жыл бұрын

Can you have the second passenger riding with this exhaust in place ? The direction of pipe seems right by pegs

@Kamdorian 3 жыл бұрын

You probably can, the exhaust gives off some heat and air but it's more pointed outwards. Passenger may feel slight warmth on the feet but not much.

@faryadi07 3 жыл бұрын

Can you please tell what type of jack you use to lift rear wheel and what these green jack pins are called near rear frame

@Kamdorian 3 жыл бұрын

The jack is the type used for any sport bike, see link here www.amazon.com/dp/B0036QZ8VQ/ref=cm_sw_r_cp_apa_glt_fabc_QF29ABFJN93DKABE9KEF?_encoding=UTF8&psc=1. And the green items are swingarm spools see link here www.amazon.com/dp/B0753H618W/ref=cm_sw_r_cp_apa_glt_fabc_H78NMJ5V1R6M12S78TDD

@bedevere007 2 жыл бұрын

sweet thanks!. I was a little confused on how you were testing the lights. Did you disconnect the black from battery and where did you connect the wiring to get it to light up? Thanks

@Alexrody1 2 жыл бұрын

On the new taillight touch the ground wire to the negative terminal on the battery, and each separate wire to the positive terminal to test

@bedevere007 2 жыл бұрын

@@Alexrody1 Awesome thanks and great bike! I ordered this and now I'm ordering your front turn signal :-) Thx

@Alexrody1 2 жыл бұрын

@@bedevere007 not my bike or my video just helping out 😅

@bedevere007 2 жыл бұрын

@@Alexrody1 thanks

@jjakkad 3 жыл бұрын

Looks great! Did you need the load equalizer or have any issues with turn signals being out of sync with the front? Also what kind of exhaust is that?

@Kamdorian 3 жыл бұрын

Thanks! My bike already had a relay installed when I bought it. I didn't add any load equalizer or anything. No issues with signals being out of sync. The exhaust is from CS Racing, it looks and sounds great and only around $650.

@omairsyed 3 жыл бұрын

@@Kamdorian I was wondering how you got the lights in sync. Mine arrives in a weeks time. Your video was so helpful. I had been looking for someone to do one. Thank you ! Also is there a reason you went with the clear when smoke would have looked cool with the black ?

@Kamdorian 3 жыл бұрын

@@omairsyed thanks I also was looking for an install video and couldn't find one so I decided to make the video myself lol. So the lights were synced fine just by plugging them in normally. My bike does have a relay installed already for the power outlet mod so the relay might be helping with the light sync but I am not sure. Relay is cheap and easy to install. I went with the clear light because I was worried the smoked light would have reduced visibility. I am not sure if it really is reduced but went with the safer clear option, although you are right the smoked would look cooler. If you get the smoked let me know how it looks!

@stevensenatore8465 11 ай бұрын

I am looking at this for my 23 KVS - since you've had this for a while (assuming you haven't changed it out) How is the visibility on it during the day? I would think for night it would be bright enough. Just concerned about daytime brightness. Thanks!

@Kamdorian 11 ай бұрын

Visibility is decent during day time. My wife drove behind me and said she could clearly see when I hit the brakes. At night it's even better of course. This is a low profile tail light so you will lose some visibility compared to the stock light but i think it's minimal loss. Good luck and ride safe!

@tfmusicpro 3 жыл бұрын

Any tips on what u did to get the fit right? I place the fender on to line it up and make it flush, but I can't tighten the screw with the fender in place 🤔 and as soon as I lift off the fender, I lose the placement I wanted 🤦‍♂️

@Kamdorian 3 жыл бұрын

It takes some trial and error of placing fender on lining up the light then remove fender and slightly tighten the light then place fender back on to confirm alignment. I did that a few times. Tighten the bolts under the light first so then you only use the adjustment screws to move the light front back left or right. The adjustment screws are on the top of the light. See time point 11:45 of the video. Good luck!

@my2wheels 3 жыл бұрын

Easy breezy!👍

@Kamdorian 3 жыл бұрын

Yes, very easy just takes some patience and trial/error to get the light aligned to the rear fender lip. This one was fun!

@meltedcupcake6463 8 ай бұрын

Is it possible to make the fender more go down? I mean make it closer to the wheel

@Kamdorian 8 ай бұрын

Only way to do this is to lower the height of the bike with different suspension. You can also adjust tightness of existing suspension so when you are sitting on the bike it goes lower.

@meltedcupcake6463 8 ай бұрын

thank you feor the response! It's always my goal to purchase kawasaki vulcan!@@Kamdorian

@forrestnome9521 2 ай бұрын

You can purchase a Savage Rear lowering kit for this bike. It lowers the rear 1.5 inches.

@scottfuller56 3 жыл бұрын

Any recommendations on what relay to buy from chrome glow they have so many haha also dont they have to be fitted up the gas tank?

@Kamdorian 3 жыл бұрын

I don't have a specific relay from chrome glow. I have the kawasaki relay already installed because I have the 12v charger port which requires the relay. I am not sure if relay is really needed though. If you have a vulcan than I recommend asking chrome glow if a relay is needed and if it is then get the kawasaki one.

@toxica.8592 Жыл бұрын

I got a question do you need a fender eliminator bar to put a universal rear light and license plate on the bike

@Kamdorian Жыл бұрын

It depends on what comes with the universal rear light and plate mounting equipment. The stock Vulcan has a terrible metal extended fender underneath the stock tail light assembly that has to be removed before mounting any aftermarket parts. Once removed you are left with 3 holes in the rear fender that can be used to mount any taillight as long as it's the right spacing for the holes on the mounting equipment. The taillight I used is made for the Vulcan 650 so it fit perfectly. There's some other options out there that fit perfect as well. Which light are you trying to use?

@toxica.8592 Жыл бұрын

@@Kamdorian none as of right now i am trying to find one but all seem to not work

@toxica.8592 Жыл бұрын

@@Kamdorian i am going to find a different one that actually goes to the bike

@SDB_Ideas Жыл бұрын

What are your Tires Sizes - It looks good and better than stock.

@Kamdorian Жыл бұрын

It is stock tire, just looks better with the new tail light because it shows more of the tire compared to the stock tail light assembly.

@SDB_Ideas Жыл бұрын

@@Kamdorian Thank You Sir. Im from Philippines and wathching your videoas especially the vulcan s modification that you did - we are preparing for my Dad's Vulcan S an upgtade from Benelli Cruiser.

@Kamdorian Жыл бұрын

@@SDB_Ideas that's great I'm glad you like the videos congratulations he will love the bike good luck

@jeremyaguirre4665 Жыл бұрын

I installed this tail light and it works seamlessly. Only now my from led turn signal is no longer flashing, just staying solid orange. I have the same Amazon aftermarket headlight that you recommended in another video. Did this happen to you?

@Kamdorian Жыл бұрын

No sorry that hasn't happened to me. You might need the flash relay module it's a simple plug in device that goes under the gas tank. Are both turn signals having that issue? Did you change the stock front then signals?

@jeremyaguirre4665 Жыл бұрын

@@Kamdorian so I removed the floppy side markers and use the headlight leds as my turn signal. They had been working fine before the tail tidy install even though they blink fast. I am hoping the device that corrects the flash speed can make them work again. Have you purchased this?

@Kamdorian Жыл бұрын

@@jeremyaguirre4665 I got this flash relay but haven't installed it yet. It is supposed to fix all the hyper flash issues and may fix your turn signal issue. It's pretty inexpensive to try out. 2-Pin Electronic LED Flasher... www.amazon.com/dp/B073J82PNF?ref=ppx_pop_mob_ap_share

@rosarioroberto5823 3 жыл бұрын

Do you have a video on how to install your new exhaust pipe?

@Kamdorian 3 жыл бұрын

I do not but here is a video from a friend on how to install. kzfaq.info/get/bejne/q9xpnrxjycmdhqs.html it's pretty easy.

@joekatchmar5235 2 жыл бұрын

Did you have to wire in the license plate light as well? My bike came with this fender but the LED's over the plate don't seem to be working

@Kamdorian 2 жыл бұрын

Yes the power wire for the plate light is black with white stripe check 13:16 timepoint in the video. It's called "tag light". It has a ground wire and the power wire for the license plate light. If the light is not working either the led is dead or the wiring was done wrong. Only way to know is to remove the rear fender and check. Beginning of my video shows how to remove the fender. Good luck!

@joekatchmar5235 2 жыл бұрын

@@Kamdorian Thank you

@joekatchmar5235 2 жыл бұрын

@@Kamdorian Well the weather finally got up to 30 here in Upstate. So got out in the garage today. Took the fender off, found the tag lights not wired or grounded. Thanks for the info. Got the light working so I shouldn't get my balls busted come inspection time

@Kamdorian 2 жыл бұрын

@@joekatchmar5235 ha that will do it! Glad you found the problem and were able to fix it. I'm done with this winter, can't wait for spring to start the bikes and ride.

@buy_da_dip8174 Жыл бұрын

So just to confirm. If i order the taillight and the relay from Amazon. Do i need anything else to else to give the bike shop to connect?

@Kamdorian Жыл бұрын

If you are using a bike shop for the install then they might be able to do a fancier electrical connection job. Otherwise they can use posi taps for the connections like I do in my video. Positaps link is here amzn.to/3K9WNuA

@buy_da_dip8174 Жыл бұрын

@@Kamdorian thanks will take a look. Did you ever move your plate to the side mount like you mentioned. I'm hesitant about laws and ahold cops writing tickets in GA for vertical plates.

@Kamdorian Жыл бұрын

@@buy_da_dip8174 I have not moved to the side yet, I have the same hesitation! I met other riders in my state that have the plate on the side and they haven't had any trouble so I guess it's fine! Will add it to the last of things left to change on the bike..

@buy_da_dip8174 Жыл бұрын

@@Kamdorian any brackets you recommend?

@Kamdorian Жыл бұрын

@@buy_da_dip8174 brackets for what?

@carakk 3 жыл бұрын

very nice video!

@Kamdorian 3 жыл бұрын

Thank you!

@da2696 Жыл бұрын

Amazing!

@Kamdorian Жыл бұрын

Thanks!

@ric.kinder Жыл бұрын

A year out, do you still like this eliminator kit? Did the quality last? How do you find the visibility at night?

@Kamdorian Жыл бұрын

Still love it, everything works fine quality is great. Visibility at night is very bright as I was told from my wife when she drove behind me. I don't do much night riding though.

@ric.kinder Жыл бұрын

@@Kamdorian If the wife approves, it's gotta be bright! Thanks for the prompt reply!

@Kamdorian Жыл бұрын

@@ric.kinder haha true that! Thanks for watching the video bro..let me know if you have any other questions

@alvaropena1220 Жыл бұрын

Have you experienced where te brake light stays on?

@Kamdorian Жыл бұрын

@@alvaropena1220 no I have not, this could mean that you switched the normal running light wire with the actual brake wire. If you switch those connections going to the bike it should fix it.

@royword176 3 жыл бұрын

Nice bike bro

@Kamdorian 3 жыл бұрын

Thanks bud!

@janmariegalban8996 Жыл бұрын

Is that a stock head light?

@Kamdorian Жыл бұрын

No it's aftermarket, check the video description for link to buy from Amazon

@janschindle1 2 жыл бұрын

Do you have amazon link for that part?

@Kamdorian 2 жыл бұрын

You can buy from Amazon here www.amazon.com/gp/product/B07G2LG9TP/ref=as_li_tl?ie=UTF8&camp=1789&creative=9325&creativeASIN=B07G2LG9TP&linkCode=as2&tag=kamdorian02-20&linkId=c8fbb7045359360bfe04ca6c1668513a. But might be cheaper if you buy directly from Chrome Glow website.

@destinedthunder 3 жыл бұрын

What a sexy bike!!!!

@Kamdorian 3 жыл бұрын

Thanks love, let's go for a ride.

@konisushiroll9936 2 жыл бұрын

what exhaust do u have? and where can i buy one? thank you.

@Kamdorian 2 жыл бұрын

It is a CS racing exhaust use this link for 5% discount at checkout csracingusa.com/Kamdorian

@rosarioroberto5823 3 жыл бұрын

Greetings, What front fender ornament do you have on?

@Kamdorian 3 жыл бұрын

It is a deer whistle, you can find it on Amazon. It prevents deers from running on the road in front of you.

@The_real_Malo1 3 жыл бұрын

My break light stays on the entire time. What can be the problem?

@Kamdorian 3 жыл бұрын

Check your wiring, sounds like you connected the running light wire from the bike to the brake light wire on the new taillight. Switch the wiring so the brake light from bike is connected to brake light from taillight.

@francescocoppolino7704 2 жыл бұрын

Sono Italiano e vivo in Italia. mi indicheresti dove poterlo acquistare? Grazie

@Kamdorian 2 жыл бұрын

Sorry I don't speak Italian, please translate to English. I wish to learn Italian one day!!

@TheNeuel 2 жыл бұрын

That looks bad ass

@Kamdorian 2 жыл бұрын

Thanks! Feels badass riding too!!

@TheNeuel 2 жыл бұрын

@@Kamdorian just ordered it

@dalecarpenter8828 3 жыл бұрын

Darker picture please I can just about make out what you working on !

@Kamdorian 3 жыл бұрын

Sorry about that bud lighting was little bit off, any steps you need help with?

@forrestnome9521 Жыл бұрын

No relay switch needed?

@Kamdorian Жыл бұрын

I believe a relay is needed, my bike came with one because the previous owner installed the power outlet.

@forrestnome9521 2 ай бұрын

💯 need a relay. It installs under the fuel tank. Plugs right into the bike.

@mealmike7574 3 жыл бұрын

Hello I have a problem I come from Austria and i need this backlight it looks sooooo great but i didnt found it can anybody help Mfg

@Kamdorian 3 жыл бұрын

Hi try these links. It can be bought from Amazon or directly from chrome glow website. amzn.to/2QLib0H chromeglow.com/products/kawasaki-vulcan-s-led-fender-eliminator-kit-with-run-brake-turn

@e.cabrera1861 2 жыл бұрын

After a year later, how is the led fender holding up?

@Kamdorian 2 жыл бұрын

Still holding strong, works great no issues.

@e.cabrera1861 2 жыл бұрын

@@Kamdorian I was hoping to hear that! When are you coming out with more motovlogs?

@Kamdorian 2 жыл бұрын

@@e.cabrera1861 soon my friend. Had a baby so been super busy with work and the kid. Will make some videos in next few weeks though!

@e.cabrera1861 2 жыл бұрын

@@Kamdorian big congrats brotha! Hope to see little Kamdorian with their own little modded out Vulcan S on your page soon lol!

@Kamdorian 2 жыл бұрын

@@e.cabrera1861 haha thanks man!! I definitely plan on teaching the kid how to ride..big wheel to bicycles to dirt bikes to motorcycles..just the way I did it!

@dashsunil 3 жыл бұрын

That's like a bike. 650 cc. Woo Hoo. 😁

@Kamdorian 3 жыл бұрын

Yes much bigger and more powerful then the 250cc in my other videos haha

@dashsunil 3 жыл бұрын

@@Kamdorian I am half way through the video now and I can see it's a lot of work. Well done. 😊

@dashsunil 3 жыл бұрын

You should be in a bomb squad. Lol That was freaking impressive. I did a rewind to see it. 🤣😅

@Kamdorian 3 жыл бұрын

@@dashsunil hahaha it's fun to play with wiring and learning new things! This was the first time I did this kind of extensive mod on a bike.

@adriaanvanderwalt5772 2 жыл бұрын

CAN YOU PLEASE SEND ME A LINK TO YOUR Exhaust!!!

@Kamdorian 2 жыл бұрын

Here you go my man! You will get 5% discount. If the link doesn't work just type kamdorian as the promo code csracingusa.com/Kamdorian

@adriaanvanderwalt5772 2 жыл бұрын

@@Kamdorian Thank you my guy this is going to be awesome!!

@Kamdorian 2 жыл бұрын

@@adriaanvanderwalt5772 yes sir excited for you. Let me know if you have any issues. Good luck and ride safe!

@sanivaeagi7124 3 жыл бұрын

Where can I buy one in new Zealand?

@Kamdorian 3 жыл бұрын

I am not sure, try Amazon or the Chrome glow website.

@bossamerica Жыл бұрын

Will this kit fit the 2022 Kawasaki Vulcan S 650?

@Kamdorian Жыл бұрын

Yes it will fit

@garomirahe1466 Жыл бұрын

Buenas!! Necesito saber si este producto tiene el marcado de homologación europeo. Gracias jeje

@Kamdorian Жыл бұрын

Hi sorry I don't know if it does have the approval mark. Most likely it doesn't but you can ask the vendor from Amazon to confirm

@jolsen76 2 жыл бұрын

Hey dude, did you have to add any type of load equalizer, or replacement flasher relay? I went on the chrome glow website and they recommend it to maintain stock flash rate. Or is that just a cash grab. LOL

@Kamdorian 2 жыл бұрын

It's true you do need a relay to prevent hyper flash. I didn't install a relay yet and I do have hyper flash. You can find cheaper options on Amazon for like $10-20.

@jolsen76 2 жыл бұрын

@@Kamdorian Appreciate it. So does your rear blinker flash too fast? Or does your hyper flash (what is that?) fix that issue?

@Kamdorian 2 жыл бұрын

@@jolsen76 yup hyperflash means it's blinking too fast. My rear signals and front turn signals all blink too fast (I also changed out my front turn signals and headlight so that's also messing with the flash speed LOL). I definitely need a flash relay asap.

@jolsen76 2 жыл бұрын

@@Kamdorian Awesome, thanks buddy. Great looking bike by the way. Gave me some great ideas for mine!! Cheers. 🍺

@Kamdorian 2 жыл бұрын

@@jolsen76 thanks man, check out my other video that shows all the mods I have so far. Feel free to use any of them on your bike. Ride safe cheers man 🥃

@ivarsmatisons 2 жыл бұрын

Interesanti interesanti

@10blood 4 ай бұрын

All that work to hide his license plate and the paper flaps up LMAO

@garretbjerke3171 Жыл бұрын

Is there a way to get the blinker to go slower?

@Kamdorian Жыл бұрын

Yes just need to install a flasher relay switch. I will have a video up on it soon.

@RAHULSINGH-mj4rd 3 жыл бұрын

Nice brooo

@Kamdorian 3 жыл бұрын

Thanks brooo!

@OBSIDIAN_GA Жыл бұрын

Brother hi how is name of your exchaust

@Kamdorian Жыл бұрын

Hey man it's CS Racing exhaust see the link on video description for 5% discount when you buy it using my link

@aalialamri5676 10 ай бұрын

Good jobs, however before was better,

@Kamdorian 9 ай бұрын

To each their own

@forrestnome9521 2 ай бұрын

💯 wrong.

@forrestnome9521 2 ай бұрын

Better at what ? Being uglier, bigger and hideous? Yes 💯

@pauld5631 Жыл бұрын

Just be sure you are still street legal for your state. Must be visible from 150ft and in inclement weather. Safety trumps looks

@Kamdorian Жыл бұрын

I agree safety first. My state doesn't require inspection for motorcycles.

@forrestnome9521 2 ай бұрын

Visible from more than that.

@SB-mw1bg Жыл бұрын

This bike always looked like it needed a bigger rear wheel.

@Kamdorian Жыл бұрын

Totally agree!! When my tires need to be changed I'll definitely be increasing the rear size.

@forrestnome9521 2 ай бұрын

I have a 185 Pitelli GT and can go bigger.

@xav6183 Жыл бұрын

Fender delete no avaiable...😢😢😢

@Kamdorian Жыл бұрын

Try this link amzn.to/43U0njR

@jamestroy34 2 жыл бұрын

Like the look, but lights aren’t strong enough to be seen clearly in the daylight. Becomes a safety issue, IMHO

@Kamdorian 2 жыл бұрын

You may be right! Knock on wood I have had no issues so far.

@Mark-ji7ek 2 жыл бұрын

I bought a used Vulcan S that has this exact led taillight. TBH the visibility is my biggest concern with the light. I am going to be replacing it with an R&G tail tidy product since I don't have the OEM parts or the OEM fender. The R&G lights are bigger than this strip yet still smaller than the stock lights. I came here to see how this part was wired. Hopefully I won't have much of an issue swapping it out, but the posi-taps make me nervous, but I assume I can just electrical tape them up after removal.

@Kamdorian 2 жыл бұрын

@@Mark-ji7ek yea the R&G will give more visibility but I like the low profile look of the chrome glow better. There is a video on KZfaq on how to install the R&G, it seems like some wire splicing is needed but yea the positaps are worth a shot! Good luck and ride safe!!