Best Lightweight Bush Hunting Rifle - MDT HNT26 Hunting Chassis

Рет қаралды 11,561

11 ай бұрын

The Link to all Links - linkin.bio/pyrate_nz
In this video I go over the #MDT #HNT26 Chassis, a new lightweight hunting chassis
~To check out my other videos or find something specific - / @pyrate_nz
~ Please Like, Subscribe & turn on notifcations - It really helps my channel.

Пікірлер: 32

@HollerHunter 4 ай бұрын

Just got the hnt26 installed on my 18.5” Tikka 6.5 creedmoor. Your video was very helpful. Super excited to hit the mountains with it. Thanks for posting.

@pyrate_nz 4 ай бұрын

Have fun!

@adamwilson8559 4 ай бұрын

Awesome review; thanks!

@milo555100 6 ай бұрын

Lovely Rig!! Well done. How long is your barrel? Did you have it cut down and threaded? Thank you for taking the time to make this video! Great job.

@pyrate_nz 6 ай бұрын

thanks. yes its cut down to a little over 16" and threaded

@milo555100 6 ай бұрын

@@pyrate_nz it seems you considered your rifle setup very well. I think about your path often. A lightweight, packable and accurate rifle that is easily supressed. Great job considering the surpessor to the stock length.

@RauberClemens Ай бұрын

5:27 On your Chassis I see a recoil lug, which mine doesn‘t have. Where can I get one?

@pyrate_nz Ай бұрын

For the tikka, it comes pre installed in the chassis. Some other actions you will need to use the factory recoil lug

@xxxoutdoorsmanxxx 5 ай бұрын

Did you have the factory bolt fluted? Or is that an aftermarket spiral fluted bolt?

@pyrate_nz 5 ай бұрын

I fluted the factory bolt.

@ArpexOfficial 5 ай бұрын

What rear monopod or rear sand bag is everyone using with this chassis?

@pyrate_nz 5 ай бұрын

I have not used a mono-pod in years. Just use a simple rear bag from Sabre Tactical. Stay tuned, i will be doing a video on shooting bags soon.

@kamilklein2880 11 ай бұрын

Hello Sir! Since you mentioned "balance": I have a similar shortened Tikka T3x (17" barrel) and I found the OEM Tikka plastic stock already too light in the rear. So my rifle ended up being quite front heavy with the suppressor attached (310 grams). So I put the barrelled action into a Tikka T3 laminated stock (second hand) to counterweigh the suppressor. How is the balance of your setup in the MDT chassis? BTW: it looks awesome! 👍 Cheers, K.

@pyrate_nz 11 ай бұрын

Thanks, im very happy with the setup. So mine balances perfectly with the balance point under the front action screw. this is with a loaded aics 3 round mag. Now i have a superlite tikka so the barrel is fluted and i have had the bolt done too, scope is a bit heavier that most too.

@kamilklein2880 11 ай бұрын

@pyrate_nz Thanks for your response! In fact I have a regular non-fluted barrel. So I went the route with the laminated stock. Looking forward for some range footage of your setup! 👍 Thanks! K.

@jianliu9420 10 ай бұрын

@@pyrate_nz what barrel length do you run? It looks like a sub 13inch?

@pyrate_nz 10 ай бұрын

16 and a bit. suppressor is an overbarrel

@kamilklein2880 10 ай бұрын

@pyrate_nz Yeah! The Kiwis have "unusually" long and slender suppressors that reach a long ways backwards over the barrel. Here in Europe/ Germany they usually reach back 10 cm/4". Seems to be a good bit more on those in NZ. Right? K.