Betaflight 4.3 Configuration Tab and GPS Tab | COMPLETE WALKTHROUGH PART 6

Рет қаралды 66,625

Күн бұрын

Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: www.fpvknowitall.com/ultimate...
SUPPORT ME ON PATREON at: bit.ly/2Ep5Sia
THIS IS MY FULL TIME JOB. Here are other ways that you can support me: www.fpvknowitall.com/support-me/
---
Watch all the videos in this series at: • Betaflight 4.3 Install...
---
0:00 - Welcome to the Configuration Tab!
0:28 - Gyro Update Frequency
• Gyro shootout: MPU6000... - Chris Rosser's gyro roundup video
3:36 - PID Loop Frequency
5:17 - Accelerometer, Barometer, Magnetometer
7:05 - Craft Name
7:56 - FPV Camera Angle Degrees
My (very old) video about camera uptilt - • Betaflight Camera Upti...
10:19 - Maximum Arm Angle
11:41 - Board and Sensor Alignment
17:51 - First Second Both Gyro
• This Betaflight settin... - Fix a bad gyro on a dual-gyro board
19:03 - Mag Align
• iNav Drone Complete Tu... - How to calibrate your compass
19:54 - Accelerometer Trim
• Calibrate & Trim Betaf... - How to trim your accelerometer
21:56 - Dshot Beacon Configuration
23:25 - Beeper Configuration
24:04 - Other Features - OSD
24:51 - Other Features - Air Mode
26:30 - Other Features - Transponder
27:20 - Other Features - Channel Forwarding
• Betaflight servo setup... - Servo how to video
28:20 - Other Features - Display
28:39 - Other Features - LEDSTRIP
• Betaflight Programmabl... - LED how to video
29:01 - Other Features - Telemetry
29:15 - Other Features - Sonar
29:56 - Other Features - Softserial
• Betaflight SmartPort T... - How to get SoftSerial working in Betaflight (this video is old but basically shows the same process used today)
30:53 - Other Features - Servo Tilt
31:20 - Other Features - In-Flight Accelerometer Calibration
32:33 - GPS Enable/Disable
32:51 - GPS Protocol NMEA vs. UBLOX, Auto Baud, Auto Config, Use Galileo
34:56 - GPS - Set Home Point Once
35:43 - GPS - Ground Assistance Type
36:25 - GPS Tab
37:30 - Next, the Power and Battery Tab!

Пікірлер: 115

@bkfpv 2 жыл бұрын

No one does these kinda series better. Thank you Joshua.

@maryjane136 2 жыл бұрын

One of my quads is equipped with a range laser which is supported by 4.3. I modified the BF source code to have a bar graph in OSD representing the height. I chase cars and for me it's very helpful to see where is my limit how low I can go because I don't want to read a numeric value all the time during the flight.

@Sir_Hubris 2 жыл бұрын

♥ words fail to explain the value of this video series ♥

@fpvclown6088 2 жыл бұрын

Have to say this series of videos has helped me understand more than i could have imagined using Betaflight so thanks JB for a great series .. amazing channel .!

@coilockerfpv 2 жыл бұрын

Literally just in time! I am setting up a new build now 😍😍

@KlononiaFPV 2 жыл бұрын

Really useful series Bardwell!! Thx SO much for all you experience and dedication👍😍

@nicholaslarson9485 Жыл бұрын

I cant thank you enough for this im going through all of them and setting up my drone, its super easy to understand. Your awesome, dont stop

@JoshuaBardwell Жыл бұрын

Glad to help!

@LAHover 11 ай бұрын

Thanks Josh! I just got back into flying and forgot everything about setting up the GPS... You saved me so much time :)

@MantraMediaCanada Жыл бұрын

Camera angle knowledge tidbit slaps! Neat. thanks JB I learned something today.

@jerodbosh7630 2 жыл бұрын

Uptilt for racing!!!! I have to try this!!! It takes 10 freaking packs to adjust from 20 degrees freestyle to 50 racing…… thanks Joshua for another great video!!!

@MrStreetboy80 Жыл бұрын

These are awesome series! Iv gone into fpv blind and had no idea about betaflight, so far Iv update firmware on a mobula6 that had mode 1 control setup and wouldn’t fly properly. So configured it from scratch, it fly’s pretty good now! I have another two drones with unknown esc and controller boards which need doing next.

@Malzanar2010 Жыл бұрын

So I haven’t flown or touched my quads in over a year… man Betaflight has come a long way. Setup seems so much more intuitive and convenient than it used to be.

@danield.8615 2 жыл бұрын

Very good tutorial! Thanks a lot for this update.

@butterflyfpv Жыл бұрын

Thank you Joshua!🙏💪

@NorthStarDrones Жыл бұрын

Another great video. Thank you

@kd2rdhlarry571 2 жыл бұрын

Well Done, very well done.

@andymattock397 2 жыл бұрын

The GepRC Cinelog30 has an odd ball fc mount configuration, it's mounted inverted & at 45⁰. For the board and sensor alignment I set roll 0⁰...pitch 180⁰...yaw -45⁰. Fantastic set of videos

@manuelsolano7525 2 жыл бұрын

Grate video Joshua learn something today.

@luvmyhondasi 2 жыл бұрын

Thanks again

@XSPHEAR 3 ай бұрын

Thanks!

@dihler55 2 жыл бұрын

I hope betaflight implements ublox7 at some point for GPSs since it allows for a higher update frequency on GPS modules that are ublox7 compatible (like the BN-880 which if you use Ublox7 on inav can update with a 10Hz rate).

@Editer38738 2 жыл бұрын

Thank you josh Cheers from Knoxville

@turionb1408 Жыл бұрын

thanks so much

@stephantertel 2 жыл бұрын

I still learned something today. So setting camera angle mixes yaw and roll. I didn`t know that, will set it back to 0 and try to feel the difference .

@wesley4713 2 жыл бұрын

So I wasn’t the only one pressing a motor to his ear and saying “no shit….”?

@bungle6334 Жыл бұрын

"ahh it's eating my face!" Great idea for a B horror movie involving murderous drones On a serious note, Josh, your videos are extremely beneficial for beginner builders/pilots. Thank you for the generous effort put into making these!

@maloriezastrow971 9 ай бұрын

Just a quick tip for board and sensor alignment. Whichever axis is correct is the one that you need to put the correction angle on.

@athenovae 6 ай бұрын

Also with Airmode and indoor flying, if you are close to anything your quad will get stuck from bumping into it all the time instead of letting you shimmy your way clear before take off.

@korydillard9617 Жыл бұрын

I had two hglrc fc's and one had a 3.20 pid loop and i thought I bricked it 😅 thanks this cleared it up

@grindz145 Жыл бұрын

Well I learned something today

@vdz89 2 жыл бұрын

love it

@Deserthacker 2 жыл бұрын

Maybe inflight accelerometer calibration could be (ab)used to keep the quad tilted forward and use it as a cruise control for level mode? Seems like a fun thing to try out.

@carlonchino Жыл бұрын

Muchas gracias por la explicación me sirve de mucho

@___fernando 2 жыл бұрын

Hi there. I'm building my first FPV drone, TYRO79(Matek F411) and I’m doing some improvements, for now, I would like to get a GPS on it. I read some articles that some people got success doing it when creating a softserial and using the led_strip pad (Pin A08) to do that as a serial_rx 11 A08 and the serial_tx 11 A02. I activated everything on betaflight (feature GPS), on ports, enabled the GPS, and on configuration enabled the GPS too. But, I didn't get it recognized on FC (betaflight). I also connected the BN-220 directly on my computer, just to confirm that it's working and it is. So, the gps unit is not the problem. I powered the gps unit on a external power supply at 5v to confirm that there's no issue with the power supply from the fc. I also tried to connect the gps unit directly on the UARTs 1 and 2, but no success. I am connecting the GPS TX pin to the FC RX pin port and the GPS RX pin to the FC TX pin port as mentioned above. It's right, correct? I'm not comfortable to invert it. I also tried different firmware versions, but no success. The last one available for this FC is the 4.2.11. Can you help me ? Thanks

@quentincampbell5865 2 жыл бұрын

33:50 The GPS icon at the top will only show when you have GPS lock. To see if your GPS is communicating properly (especially indoors), check the GPS tab. You should see some sort of activity there if it is communicating.

@johnnyrocket3200 2 жыл бұрын

Thanks for reminding me to hit the LIKE button. I keep forgetting. LOL!😂

@fayazmd83 2 жыл бұрын

Thank you so much Joshua for making highly informative videos! I upgraded my Trashcan from BF 4.1.0 to 4.3.0. I noticed that actually some PID controller settings are changed after the upgrade. for eg. feed forward, dynamic damping etc. I restored them to original settings. As you mentioned that after you import the preset (saved file from earlier firmware) into the newly flashed firwmare, all factory settings should be applied/restored. I performed this step as well. Everytime I fly the quad after a few seconds of flight, the motors get disarmed. Can you please suggest what might have gone wrong?

@AEMBowers 2 жыл бұрын

I've got the weirdest situation going on. I just received an RTF quad from GetFPV. In the configurations tab on Betaflight (BF), it has the flight control (FC) set at 0 roll, 0 pitch, and 0 yaw. However, the gyro is set at CW 180. At the same time, I can see that the FC has physically been rotated 180 upon install (the arrow points toward the tail of the quad). Based on JB's instructions, the settings in BF's configuration tab should instead be: gyro set to 0 degrees, while the yaw for the flight controller is set to 180 degrees (I put -180, since I assume this corresponds to CW--it might matter for the math, as you'll see below). With either setup, physical movement of the quad matches that shown in Betaflight's Setup tab. This makes sense to me, and I will change it to how JB recommends. The issue is that I would now like to install a Matek M8Q-5883 GPS w/ compass. The manual for this GPS states that, if the arrow of the GPS points in the same direction as that of the flight controller, the Mag alignment in Betaflight's configuration tab should read CW 270 flip. For the best mounting and cable running for my GPS, I do in fact want the arrow on the GPS to face the same as that of the flight controller. However, the FC was mounted CW 180 as previously mentioned. So, do I need to input a mag alignment reading of CW 270 flip + CW 180 = CW 450 flip or, in other words, CW 90 flip? I realize that I can test this, but I won't have the ability to for a few weeks, and I'd simply like to know the theory in any case.

@GifyTheOld 2 жыл бұрын

0:50 I think you said small mistake there, because Accelerometer is for measuring how something is accelerating (how fast is moving) on certain axis in some unit per second, and gyroscope is used to tell, whitch direction is up (like artificial horizon in airplane)

@staydown.normal5323 2 жыл бұрын

i want to see you set the drone up like the tune lol

@jeffreynolds2190 2 жыл бұрын

is it possible to physically disconnect the GPS wire harness in the field or a building if Im having trouble , or Is it possible to put an in line switch in the GPS wire harness , would the quad operate at all ?

@kenwu324 Жыл бұрын

Need help! Switch from TX16S to Spektrum (both runs crossfire) for my diatone Roma f5 DJI v2, tx16S runs great, but after set up on spektrum with crossfire, it only can be armed but no throttle response. All beta flight 4.3 seems ok, like sticks moving/travel aux switches etc. What have I missed, please help

@guytas 5 ай бұрын

ok, 4 months later, I have another question on compass. I have installed the GPS with magnetometer. I also adjusted the declination related to where I live. Now the compass on the betaflight screen shows pretty much the right direction. But the thing that bugs me is if I rotate the quad on my desk, I see the compass moving along with the rotation. But when I stop rotating, I see the compass readjusting itself more or less depending on how many degrees I rotated. For instance, when I rotate to about 90 degree, the compass re-adjust to about 2 more (or less) degrees. It's almost like if the gyros degrees are not the same width as the mag degrees. It's weird.

@1911doc 2 жыл бұрын

Hi JB, Today I put first time BF 4.3 on my quad, micro apex 4" and have some weird problem that I cannot takeoff normally. Quad arms as usual, no funny noises and when you want to takeoff quad goes like 5cm in the air and just wont go higher, even if I put 100% throttle it will just hover 5cm from the ground. It feels like some flying mode is active that prevents me to fly normally...Just to mention, on BF 4.2.11 quad flew normal, just needed a tune. Wanted to do some blackbox logging on stock BF settings but just couldn't takeoff. Any ideas? Thanks!

@4li60 2 жыл бұрын

Hi Joshua, I have a HGLRC Veyron 35 CR Analog and can not get to have the flight timer showing in the OSD. I have ticked all the blocks in the OSD menu but nothing. Same with the flight modes. Any idea what I'm doing wrong here?

@Sleeperknot 6 ай бұрын

Hi Joshua, Thank you for your videos! I have a question: I have connected a Ublox Neo 6M GPS module to my quadcopter, which is based on the Speedybee F405 v3 and running Betaflight 4.4.3. In the Betaflight configurator, I can see that I have a 3D GPS fix, and when I issue the "gpspassthrough" command, I can see data being written to the CLI. However, I've noticed that the GPS icon in Betaflight does not turn yellow. I have connected the GPS module to UART6, disabled auto baud (although I have also tried enabling it), enabled auto configuration, and set the baud rate to 115200. I'm wondering why the GPS icon is not turning yellow. Should I be concerned about this issue, or can I just ignore it? It's worth noting that even with this issue, the quadcopter arms with Return to Home (RTH) configured, which is set to disable arming without a 3D fix.

@Idontdohandles 2 жыл бұрын

On the GPS topic - having a hellish time getting a GPS going on a board I pulled from the Crux3.5. I put a Beitian 220 on UART1 - rx1/tx1 --- and when i set it up for GPS as instructed -- I am not getting the yellow confirmation "GPS" indicator in Betaflight that FC and GPS are communicating, of course, no fix either. I've tried everything - a different GPS - Beitian 180, swapping out Rx and Tx wires just in case I have them backwards - power lights are coming on for the GPS unit, FC is otherwise BRAND NEW and in perfect working condition. BAUD rate i set auto and manual --- auto its jumping to 57k on its own. Now stumped. :( Something up with UART1 not able to be GPS --- this is an ELRS SPI Antenna on the board -- does that maybe mean UART 1 is not available if i'm using the SPI antenna -- wouldn't make any sense though. Grrr its 4am and still trying at it.

@tracy1267 11 ай бұрын

i have the explorer the default PID is set at 200KHZ /cycle time 493/cpu load 28 the highest it will go is 400KHZ/ cycle time 247/cpu load 42 would it be safe to go to 400? will it even be noticeable seems strange it's set so low.

@ls4life544 2 жыл бұрын

Great video! question if someone could answer it. What would be the negative effect of making the board alignment fix using first gyro? I have fixed the issue of not facing the direction I moved the quad using the option "first Gyro," and it still flights as I think it should be based on my base judgment.

@JoshuaBardwell 2 жыл бұрын

There is no disadvantage, as long as you get the alignment right. But since boards don't always default to 0 degrees rotation as default, setting that value can be unintuitive.

@MrRyan4113 2 жыл бұрын

Hey Joshua, i have an flight succex-d whoop aio, fitted to a Geprc 25 frame with the AIO pointed correctly forward (arrow), i used a frame adapter. in calibration the board is right way up but as a pusher the motors need to face down how do i flip the motors?i'm confused as what to do next. thanks JB.

@JoshuaBardwell 2 жыл бұрын

Make sure the motor is spinning the right direction, when looked down from the top. Install props the right way up, when looked down from the top (so, upside down relative to the motors).

@tenuris Жыл бұрын

I got a Blitz F7 with the BMI270 gyro. Now I see 3,2khz gyro loop. What would be the matching DSHOT Protocol? 150 or 300? Thanks ❤

@Inertia888 Жыл бұрын

You probably figured it out by now, but it's DShot300.

@DimmyV 10 ай бұрын

I wish beta flight just had descriptions of what each function does

@StefanoScardigno 2 жыл бұрын

Hi JB, when you use a SOFTSERIAL....how can someone understand what is the correct pad mapped to the RESOURCE of betaflight? Thanks and good Job

@JoshuaBardwell 2 жыл бұрын

kzfaq.info/get/bejne/nbJhd9uGq9CqoWw.html

@shivanshpratapsingh4678 2 жыл бұрын

Hey Joshua, i am using zeus 25 AIO FC and after flashing it i can't see the mixer tab in configuration part can you tell me what is wrong?

@JoshuaBardwell 2 жыл бұрын

In confused because Betaflight doesn't have any Mixer tab.

@jakeh3144 2 жыл бұрын

I had no idea that noise when plugging in the battery was from the motors, I assumed it was ESC or FC

@1870movie Жыл бұрын

I feel you need to understand Airmode in BF 4.3 has a very bad user experience for some people. For some of us (not all and I do not know what only some), Airmode causes a runaway that is not detected by runaway detection (very bad). When Airmode is enabled and the quad is armed, the motors spin as expected. Once the throttle is raised, then immediately a runaway occurs. People with this problem find switching back to BF 4.2 resolves the problem. I have been pulling my hair out trying to understand why and this is what I found. I found the problem can be resolved with two options: 1) disable Airmode and enable motor stop (not desirable) 2) disable Airmode and set Dynamic Idle Value (found in PID Tuning) to 3000 to 4000 RPM as recommended in the BF Wiki This problem is present any time Airmode is enabled even with Dynamic Idle enabled or disabled. According to the BF Wiki, dynamic idle has been rewritten in BF 4.3. I assume the BF developers are not aware of this runaway problem as a result of rewriting dynamic idle. Maybe you can help raise awareness of this safety problem. Here is an example of the problem. This does not seem as severe as a runaway like I am experiencing, but this looks to be the same problem. github.com/betaflight/betaflight/issues/11655 By the way... Thank you for your excellent service to this sport!!!

@JoshuaBardwell Жыл бұрын

If airmode causes a flyaway, there is some other mechanical problem with the quad. The gyro should not get enough feedback to cause flyaway even with airmode enabled. Turning off airmode obscures the problem, but it's like putting a splint on a broken ankle. You might still limp on it, but it's not fixed. This isn't a betaflight bug. It's damaged hardware or improper building methods (no disrespect intended to the builder).

@1870movie Жыл бұрын

@@JoshuaBardwell Thank you for the feedback. I am surprised the problem is with the quad since the quad flies great with Airmode turned off. The flight controller is new. Should I use rubber mounts?

@MysteryD Жыл бұрын

8:10 anyone else notice the gnarly bell separation on that motor?

@joecachia2 2 жыл бұрын

Hi Joshua, Great work as always. So helpful. Small question from a newbie. I ordered a tyro79 rtf kit , as my first beginner quad. Now I have no idea what Betaflight version it comes with . but I am assuming that if i had to flash the firmware to 4.3 , I would loose all the settings it currently has right ? Would flashing to 4.3 , still have some default values and keep the quad operable or would most stuff have to be manually set ? Would it make sense for me to take screen shots of all Betaflight tabs , so that I have a ref of what settings there were ( apart from taking the CLI backup of course ) ? I also plan to take note of the original Betaflight ver it has so I can revert back to it along with the CLI backup.

@JoshuaBardwell 2 жыл бұрын

Please start at part 1 of this series where I show how to back up settings before flashing. That will ensure you can go forward without losing the old config if you want to go back. You will lose all the manufacturer settings but you can use this safe migration tool to bring many of them forward. bf43-safe-migration.robertodedomenico.it/

@joecachia2 2 жыл бұрын

@@JoshuaBardwell thanks . yes I saw that bit as well . but I am not confident to know what to move forward and what not. But thanks for answering. Guess I could try fly it before I tart messing ... lol.

@guytas 9 ай бұрын

At the beginning of this video you show how moving the gyros moves the quad on the screen. I can see on your screen, that the compass in the INSTRUMENTS panel moves too. But how do you set this compass north? For me, the north is always where the quad was pointing at power on. Sounds strange. But my main concern is this: will this affect the return to home feature if I powered it on facing other direction?

@JoshuaBardwell 9 ай бұрын

That's because you don't have a compass. So the quad just guesses that north is where you were facing when you powered up. No, it won't affect return to home. The FC knows that isn't really where north is.

@chriskasten376 7 ай бұрын

@@JoshuaBardwellSo in theory, if I set my quad due north when arming, my goggles should show approximately the correct heading?

@sburnham3 2 жыл бұрын

wonder if the betafpv cetus uses the sonar setting through beta flight for height?

@baggszilla 2 жыл бұрын

I think that's LiDAR that the Cerus uses. We would have to see the diff all from the cetus to know.

@edcoppen Жыл бұрын

How does max arm angle tie in with flop over after crash please? If I crash upside down and disarmed in a panic, can I rearm and use flip over after crash if max arm angle is enabled pls?

@JoshuaBardwell Жыл бұрын

Max arm angle is ignored when in turtle mode.

@edcoppen Жыл бұрын

@@JoshuaBardwell Awesome, thank you. I'm new to fpv, it's a deep rabbit hole. Your channel is a life saver!

@viniciuscamargos724 2 жыл бұрын

I’ve tried but could not trim accelerometer using my controller (Jumper T-pro, with ELRS external module, binding with mobula 7 Hd-Zero). Do you it could be one more issue of this model (Jumper t-pro)? Do you suggest me to do something else?

@viniciuscamargos724 2 жыл бұрын

I tried to do it landing, as you showed on your old video linked below this new one.

@JoshuaBardwell 2 жыл бұрын

You have to have angle mode activated for the trim to work.

@illuminatorix 7 ай бұрын

Hello! May I ask something? My RX has telemetry option and I see my quad's status on my radio (everything, yaw, pitch , gps etc), yet I have no Telemetry option to enable or disable on the configuration tab! Is it something I do wrong maybe? Thanks!

@JoshuaBardwell 7 ай бұрын

They moved it to the Receiver tab now.

@illuminatorix 7 ай бұрын

@@JoshuaBardwell Thanks for replying J.The moment I asked the question, after some minutes I found it on the RX tab!!!! Thank you for one more time!!! Your videos are really helping people!!!

@garyreinke5161 2 жыл бұрын

Setting up Mobile 6 using BF 4.3. Channel map TAER. No warning flags. Receiver tab shows all stick movement.. In motor tab, motors will run in A, E, and R but not T. Any thoughts?

@JoshuaBardwell 2 жыл бұрын

If only 2 motors spin and only when you deflect pitch roll and yaw then it means turtle mode is active in the modes tab. Flip the aux switch to deactivate turtle mode.

@garyreinke5161 2 жыл бұрын

@@JoshuaBardwell Thanks. I was too quick in asking for help when I found one of your videos solving my problem

@flyguycinematic6030 2 жыл бұрын

I have a question on the configuration to set up the receiver I recently downloaded the new beta flight and I what is using an older flight controller but I seem to have lost my connection to my transmitter I have no transmitter inputs to determine what I’m using I happened to be using specktrum. I basically have nothing to make my Radio transmitter function. Thank you I hope I can figure this out with your help.

@JoshuaBardwell 2 жыл бұрын

You can get this info from the saved config dump that you made before you flashed. If you don't have that, the two steps are to configure ports tab and receiver tab, both of which are covered in this series.

@flyguycinematic6030 2 жыл бұрын

@@JoshuaBardwell thank you for the time your giving me. So yes I watched all the videos and I had set The port then found my receiver set up I did exactly everything reading the manual on the flight controller which is RX1 for my serial RX to my Spektrum. My set was UART1 for serial RX, Spektrum1024 for my receiver. Still no stick inputs happening. It was flying two days ago then I just updated to the latest version of Betaflight and now it doesn’t recognize my radio transmitter because I’m seeing no inputs on the computer. It worked fine just before the update firmware.

@flyguycinematic6030 2 жыл бұрын

@@JoshuaBardwell CLI dump files didn’t help also do you think that the serial RX inverter has been set differently after Firmware update? FC has a designated plug for my satellite RX which is 3.5 V I have a old X racer F4 no damage. Like I said it worked perfectly fine I just updated to the new Betaflight, now this is my issue.

@fiku4444 2 жыл бұрын

for me telemetry is moved to receiver tab tang 2 + nano

@JoshuaBardwell 2 жыл бұрын

Yeah they moved it since I made this.

@Fly_High_FPV 2 жыл бұрын

Are you sure the FPV camera angle changes flight characteristics? I just tested at 45 degrees and 0 degrees, I hover the quad in acro and do a yaw spin, both spin perfectly flat. I really dont think this changes anything in flight. Happy to be proven wrong

@JoshuaBardwell 2 жыл бұрын

If you are hovering, then no, the camera angle has no effect, except that with higher uptilt you're looking at the sky. The difference comes when you are in forward flight, and you have leveled the horizon in your goggles. With higher uptilt, you are pitched forward more, so the mix of roll and yaw required to turn is different.

@Fly_High_FPV 2 жыл бұрын

@Joshua Bardwell i understand crosscoordinating turns and how camera tilt effects that in flight. I'm just not convinced that setting the FPV cam angle in BF has any impact on flight dynamics, are you certain it does?

@Fly_High_FPV 2 жыл бұрын

Ok, so BF does have compensation, but it's dynamic and varies based on how close you are to the set pitch angle 👍

@FluffRat Жыл бұрын

I thought all it did was offset the horizon line in the OSD? I've been using it like that never even thinking it might change flight characteristics and haven't noticed any weird yaw/roll shenanigans at all.

@Fly_High_FPV Жыл бұрын

@FluffRat it does change flight characteristics, closer to the tilt angle, the more it compensates

@turbomaker4 Жыл бұрын

hi do you have any idee why the gps have a fix and got speed and position but betaflight 4.3 cant see any sat 🤨 so gps rescue wont work

@JoshuaBardwell Жыл бұрын

Check wiring of TX and RX to FC. Make sure TX goes to RX and RX goes to TX. In Ports tab, make sure GPS is configured on the right UART that the wires go to. In Configuration tab, enable GPS, set type UBLOX, auto baud, auto configure.

@turbomaker4 Жыл бұрын

@@JoshuaBardwell wow thanks for that fast reply

@rishithakur1551 2 жыл бұрын

Hi JB. I have sent you an email about MPU6500 gyros, but I'm not sure you'll get to read it as you probably have hundreds of emails! Is the mpu6500 gyro now working well with betaflight, or is it still plagued with vibration related issues? (I ask as I ordered 4 mpu6000 based fcs, 2 diatones and 2 HAKRCs, and all came with either MPU6500 or no gyro chip at all and the manufacturers said these work well now -full story in email!!!)?

@JoshuaBardwell 2 жыл бұрын

I'm not sure about that. To be honest, I'm surprised anybody is still selling FC with MPU6500 on it.

@rishithakur1551 2 жыл бұрын

@@JoshuaBardwell Thanks JB. I'd appreciate any advice if and when you know more. Strange two different manufacturers did this -I rekon others have too, but people might not have realised/noticed!