Всем привет!
В данном видео смотрим на малыша от BetaFPV которого зовут Pavo Pico! Так же, установим на него RunCam Link (аналог Cadd Vista) но с курсовой камерой Caddx Polar Starlight... вот такой вот гибрид :) Ну и конечно полетаем на Pico в темноте...
00:00 Вступление
00:40 Обзор BetaFPV Pavo Pico
04:15 Устанавливаю цифровой VTX RunCam Link (Vista)
08:26 Смотрим на собранный Pavo Pico с камой Caddx Polar Starlight
10:31 Прошиваю ELRS приемник
12:02 Базовая настойка в Betaflight configurator
15:55 Летаем на BetaFPV Pavo Pico
19:15 Заключение
Полный DUMP Pavo Pico (F405 2-3S 20A V1.0 FC BETAFPVF405 4.4.1 ) - clck.ru/36v5ox
=======================Мой diff all========================================
diff all
version
Betaflight / STM32F405 (S405) 4.4.2 Jul 25 2023 / 11:50:06 (23d066d08) MSP API: 1.45
config: YES
start the command batch
batch start
reset configuration to default settings
defaults nosave
board_name BETAFPVF405
manufacturer_id BEFH
mcu_id 0031001d4e31501320373141
signature
name: Pavo Pico
feature
feature -TELEMETRY
serial
serial 3 131073 115200 57600 0 115200
beeper
beeper -GYRO_CALIBRATED
beeper -RX_LOST
beeper -RX_LOST_LANDING
beeper -DISARMING
beeper -ARMING
beeper -ARMING_GPS_FIX
beeper -BAT_CRIT_LOW
beeper -BAT_LOW
beeper -GPS_STATUS
beeper -RX_SET
beeper -ACC_CALIBRATION
beeper -ACC_CALIBRATION_FAIL
beeper -READY_BEEP
beeper -DISARM_REPEAT
beeper -ARMED
beeper -SYSTEM_INIT
beeper -ON_USB
beeper -BLACKBOX_ERASE
beeper -CRASH_FLIP
beeper -CAM_CONNECTION_OPEN
beeper -CAM_CONNECTION_CLOSE
beeper -RC_SMOOTHING_INIT_FAIL
beacon
beacon RX_LOST
beacon RX_SET
led
led 0 0,0::CO:10
led 1 1,0::CO:10
aux
aux 0 0 0 1700 2100 0 0
aux 1 1 1 900 1300 0 0
aux 2 2 1 1300 1700 0 0
aux 3 13 2 1700 2100 0 0
aux 4 35 3 1650 2100 0 0
master
set gyro_lpf2_static_hz = 0
set dyn_notch_count = 0
set dyn_notch_q = 500
set gyro_lpf1_dyn_min_hz = 0
set acc_calibration = -7,18,-15,1
set baro_hardware = AUTO
set rssi_channel = 15
set blackbox_sample_rate = 1/2
set blackbox_device = NONE
set dshot_idle_value = 1150
set dshot_bidir = ON
set motor_pwm_protocol = DSHOT300
set motor_output_reordering = 2,3,0,1,4,5,6,7
set align_board_roll = 180
set vbat_min_cell_voltage = 335
set vbat_warning_cell_voltage = 345
set ibata_scale = 510
set ibata_offset = -300
set small_angle = 180
set pid_process_denom = 2
set osd_vbat_pos = 2126
set osd_rssi_pos = 192
set osd_link_quality_pos = 2170
set osd_rssi_dbm_pos = 2138
set osd_rsnr_pos = 160
set osd_tim_2_pos = 2432
set osd_flymode_pos = 2478
set osd_throttle_pos = 2266
set osd_crosshairs_pos = 2317
set osd_current_pos = 2234
set osd_craft_name_pos = 2112
set osd_warnings_pos = 14699
set osd_esc_tmp_pos = 129
set osd_core_temp_pos = 225
set vtx_band = 0
set vtx_channel = 0
set vtx_power = 0
set vtx_freq = 0
set vcd_video_system = HD
set craft_name = Pavo Pico
profile 0
profile 0
set p_pitch = 56
set i_pitch = 70
set d_pitch = 54
set p_roll = 53
set i_roll = 67
set d_roll = 45
set p_yaw = 53
set i_yaw = 67
set d_min_roll = 43
set d_min_pitch = 51
set feedforward_averaging = 2_POINT
set feedforward_jitter_factor = 10
set simplified_i_gain = 70
set simplified_d_gain = 145
set simplified_pi_gain = 120
set simplified_dmax_gain = 15
set simplified_pitch_d_gain = 105
set tpa_rate = 66
profile 1
profile 2
profile 3
restore original profile selection
profile 0
rateprofile 0
rateprofile 1
rateprofile 2
rateprofile 3
restore original rateprofile selection
rateprofile 0
save configuration
save
========================================================================
\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/
Мой канал в Телеграмм: t.me/zhukoramafpv
Группа в VK: zhukorama_fpv
Мой канал на Яндекс.Дзен dzen.ru/zhukoramafpv
Мой канал на RuTube: rutube.ru/channel/24772689/
/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\
#hobbyfly, #betafpv , #pico