No video
How to Remove Honda Rotor Screws
Рет қаралды 61,174
Күн бұрынHow to Remove Honda Rotor Screws. In this video I show how to remove Honda rotors screws. Sometimes getting rotor screws off of Hondas can be tricky, I give some tips with dealing with them. Enjoy!
Be sure to subscribe for more tool and car repair videos!
/ bigdog50001
/ bigdog50001
/ bigdog50001
Disclosure: This channel earns a small commission using some of these links - at no additional cost to you.
The Big Dog 50001 Automotive Channel Store can be found here: www.amazon.com...
Tools and Parts:
Vessel JIS #3: amzn.to/2O8UVG8
Vessel JIS #2: amzn.to/2O9g7M8
Trusty Cook Hammer: amzn.to/35n8QxN
Punch Set: amzn.to/2QB4wah
Honda Rotor Screws (for this 2007 Accord): 93600-06014-0H
Honda Rotor Screws (Aftermarket): amzn.to/37p9TPG
Anti Seize: amzn.to/2rhzbyQ
48 Piece Extractor Kit: amzn.to/33bkHgW
Want a free Big Dog50001 sticker? Send an email to bigdog50001@gmail.com requesting a sticker. Sorry, no international addresses or automotive questions.
Have something you would like to send to Big Dog50001?
Send it here:
Big Dog50001 Automotive Channel
P.O. Box 726
Cortaro, AZ 85652
2019 Epidemic Entertainment. All rights reserved.
Disclaimer:
Due to factors beyond the control of the Big Dog50001 Automotive Channel, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. The Big Dog50001 Automotive Channel assumes no liability for property damage or injury incurred as a result of any of the information contained in this video.
The Big Dog50001 Automotive Channel recommends safe practices when working with power tools, in on or around automobiles or other vehicles, automotive lifts, lifting tools, jack stands, electrical equipment, automotive modules and systems, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of the Big Dog50001 Automotive Channel, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not the Big Dog50001 Automotive Channel.
@BigDog50001 4 жыл бұрын
*Tools and Parts* Disclosure: This channel earns a small commission using some of these links - at no additional cost to you. Vessel JIS #3: amzn.to/2O8UVG8 Vessel JIS #2: amzn.to/2O9g7M8 Trusty Cook Hammer: amzn.to/35n8QxN Punch Set: amzn.to/2QB4wah Honda Rotor Screws (for this 2007 Accord): 93600-06014-0H Honda Rotor Screws (Aftermarket): amzn.to/37p9TPG Anti Seize: amzn.to/2rhzbyQ 48 Piece Extractor Kit: amzn.to/33bkHgW The Big Dog 50001 Automotive Channel Store can be found here: www.amazon.com/shop/bigdog50001automotive
@dr_920 4 жыл бұрын
I remember last time when I tried to replace the rotors and couldn't get those out with a regular screwdriver. It was your video that helped me understand I need a JIS tool. Thanks.
@BigDog50001 4 жыл бұрын
Glad it helped you before, thanks for the comment!
@rickir808 4 жыл бұрын
I can’t tell you how many times I’ve hit my hand lol. Life of a mechanic. Another simple but informative vid! Thanks!
@BigDog50001 4 жыл бұрын
I know right! I could have edited it out but I figured I would show what it is really like sometimes. Thanks for the comment!
@jimthecarguy 4 жыл бұрын
Nice demonstration on the use of that tool. The right tool for the job
@BigDog50001 4 жыл бұрын
Thanks Jim!
@Glenn_123 4 жыл бұрын
Another great video!!! Oh how we love those Honda screws!
@BigDog50001 4 жыл бұрын
Like a love/hate relationship lol!
@MrSamPhoenix 11 ай бұрын
With the Vessel Impacta tool I’m not even scared to put them back in lol
@cadleo 2 жыл бұрын
So, I just changed all my calipers, rotors and pads and bled my fluid on my 09 Accord and all Ive ever done is change my own oil. Ive never even seen someone do brakes before besides on KZfaq. It went great and your video was extremely helpful to the whole process. Thank you so much! In addition to all of that, the two rear rotors were the original with JIS screws. I saw this video before I did them and got this tool just in case I needed it. I needed it! lol one of those rotors was a bitch. But a night of whacks and WD40 sessions and it was off. You rock.
@BigDog50001 2 жыл бұрын
Thanks for the comment 👍!
@TheDisgruntledMechanic 4 жыл бұрын
A little tip Eric O. gave quite a while back and I use with rust for screw heads, valve lapping compound on the screw driver tip. It really helps keep the point of the screwdriver in the head. try it sometime. good tips! Happy Thanksgiving Dave!
@BigDog50001 4 жыл бұрын
One of these days I need to give that a try!
@Aardvark49 4 жыл бұрын
So nice to see eye protection in use. I watch a lot of car videos made by pro techs - I'd say the majority of them are very careless, especially when working underneath the vehicle.
@BigDog50001 4 жыл бұрын
All fun and games until you get something stuck in your eye!
@MrSamPhoenix 11 ай бұрын
I bought the Vessel Impacta N° 3 for the Honda brake rotor screws. It did the job with a four pound sledgehammer 🔨 with ease.
@wyattoneable 4 жыл бұрын
As you spoke and showed us some great tips I was looking for any dirt on your floor. Nope, it was spotless. (ha ha) I don't own any impact screw drivers and there have been a few instances where they would have come in handy. I do have the style that rotates as you hit it and that has worked. My gloves never last more than one hammer hit either. :)
@BigDog50001 4 жыл бұрын
I hate is when gloves only last one hammer hit! ;)
@franchaza796 Жыл бұрын
2023 is going to be my first time removing these screw, thanks for the info about screwdriver
@lukecouture8346 9 ай бұрын
Make sure it's your last. Don't reinstall them. They aren't needed and only become more of a pain to get out during the life of your car
@johnnyo5915 2 ай бұрын
Man, you seem like a good Dude thanks for this video. I am retired and on a budget so I have to save money wherever I can..Ill give her a try!!
@billsmith2212 25 күн бұрын
Some recommend putting 2 lug nuts on to take the tension off the screws . Then back out the screws .
@dj5752 9 ай бұрын
Use an air hammer with the shake and bake tool attached to it. Game over.
@themechanic6117 4 жыл бұрын
I was going to buy a set of vessel screwdrives but i decided to go with the air hammer attachment made to remove these screws . it works awesome! Hasnt failed me yet
@BigDog50001 4 жыл бұрын
That is always an option too!
@treehouse7861 3 жыл бұрын
2 of the best honda G's
@dps6198 4 жыл бұрын
No need to put those screws back in but I would line up the holes. You should also wear hearing protection as well.
@BigDog50001 4 жыл бұрын
If it is your vehicle, yes I agree they can be left off. If I am working on someone else's vehicle, I always reinstall them. Thanks for the input!
@davidkelley2657 5 ай бұрын
Great explanation of what and why.and easy wach and do.thank you
@BigDog50001 5 ай бұрын
Thanks 👍!
@matthewespindola 10 ай бұрын
If you are reading this and having trouble taking the screws out, you could buy the Quinn heavy duty impact screwdriver kit from your local Harbor Freight.It's about $35 but it's worth it. It had 4 bit heads included. I've made quick work of rotor screws on multiple Hondas with this tool. Harbor Freight tools are hit or miss, but this one definitely has saved me from drilling out rotor screws, which trust me is not fun. Make sure you're still using PB Blaster beforehand on the screws, especially if this is an older car.
@domenickpanichelli4854 Жыл бұрын
These screwdrivers look great and I'll definitely be getting a set, but I didn't have them available. So word of wisdom, you can use a really thin punch that only touches the center, deepest point of the screw head and give it a few spirited smacks. Came right out for me 👍
@nathanield.4527 4 жыл бұрын
The best part about your videos is that you take the time to answer questions. Didn’t you have a few videos where you use a die grinder to clean around the wheel studs and brake hub using a roloff disk and OTC brake hub kit?
@BigDog50001 4 жыл бұрын
Yes, that is typically how I do brake jobs, thanks for the comment!
@nathanield.4527 4 жыл бұрын
Big Dog50001 Automotive On your next brake job, can you use your Milwaukee M12 die grinder and OTC brake hub kit? Your previous videos used the pneumatic grinder. I am considering purchasing the Milwaukee in the near future. Thank you.
@HumanScourgeYT 2 ай бұрын
I wish i watched this day before yesterday😭😭😭
@willytv275 6 ай бұрын
Great video - I have a 2015 Crosstour, it has the two small screws, like your vehicle. However, it also has a third larger screw, at least I guess it’s a screw, it has the OD of maybe a nickel with a rectangular cut out in the center. What is that?
@francoisdubois80 2 жыл бұрын
brilliant ... the JIT vs SAE phillips tip threw me off so I ordered the tool from Amazon
@robertjohnson4401 4 жыл бұрын
I have that exact same Vessel tool. It did not work on all four of my wheels. I will try to heat with a torch and then use an air impact with a flat punch and then try the Vessel tool again.
@johnvolpert8295 Жыл бұрын
I'm having the same problem. Did anything end up working?
@robertjohnson4401 Жыл бұрын
@@johnvolpert8295 I used a large flat punch. Hit punch over screw head with a large hammer. Then use Vessel tool. No heat was necessary.
@johnjkizer6399 3 жыл бұрын
Great video but have you ever tried putting back the lug nuts and Tighten them back on then simply unscrew the rotor screws, it takes a lot of pressure off the screws, I use this trick all the time , peace and God Bless
@BigDog50001 3 жыл бұрын
I don't typically do that but thanks for the input, others may want to try it!
@erric288 2 жыл бұрын
Thanks be to God for you and this comment! Saved me a boat load of constrination. I was using a sledgehammer with the vessel by the time I was searching the comments. Once I put back on the lug nuts, the rotor screws practically fell out they were so easy to unscrew! If anyone else is having trouble, do this!
@Palaseo 4 ай бұрын
Watched all lot of videos and end up here… Wow, yup . . . just needed a person who could explain to me that I was not using the correct tool
@BigDog50001 4 ай бұрын
👍
@TechCrazy 2 жыл бұрын
Just curious if spraying a little deep creep from Seafoam, wait and then use a rotary hammer with a drill setting with a screw bit work for this?
@MrINFAMOUSKING 4 ай бұрын
What’s the success rate of this method?
@billcarey9184 2 жыл бұрын
That’s when it works perfectly. Most of us are looking for when it doesn’t
@BigDog50001 2 жыл бұрын
I talked about different ways to deal with them, including when it doesn't work perfectly.
@ronald5728 5 ай бұрын
Nice video. Good explanation.
@mikea5205 4 жыл бұрын
I bought that same screwdriver..I wacked it until Christmas and the screws still didn't come out. I used the last resort of drilling.
@BigDog50001 4 жыл бұрын
That can happen, thanks for the input!
@Kons213 4 жыл бұрын
Man, did I struggle with these screws when I was replacing rotors on my Civic for the first time. Was like - why. would. you. not. TURN?!?!?! Didn't know back then I had to use impact screwdriver..
@BigDog50001 4 жыл бұрын
They can be tough the first time, thanks for the input!
@rv49er 3 жыл бұрын
That jack stand looks like the ones Harbor Freight recalled. I had a set and they took them back.
@abdulsalamshar5601 4 жыл бұрын
Hey bigdog, sam from saudi, i have accord 2.4 2005 the coolant goes to overflow tank and not back to radiator, there is no bulding pressure in radiator, i replace oem cap but did nothing, i check engine & transmission deb-stick there is no oil coolant mixer , on radiator i find little oil on cap, what could cause that? No leaks for coolant any where . Thank you sir
@BigDog50001 4 жыл бұрын
Scotty?? Come on, I didn't say "Rev up your engines"!
@abdulsalamshar5601 4 жыл бұрын
@@BigDog50001 lol sorry forgot to delete it 😂😅
@carlnikolov 3 ай бұрын
Great video. Thanks a lot.
@kdmq 3 жыл бұрын
I did brakes for a buddy on a Hyundai Sonata and got 3 out of 4 rotor screws out using a variant of this method. I had screwdrivers with removable bits so I could hammer in just the bit by itself into the screw, then hook up the screwdriver and just unscrew it like a normal screw. The last rotor screw stripped off the head so I put a thick flat head bit into my screwdriver and used it as a chisel, hammered it into the head to get a bite on it and started hammering counterclockwise and the last screw came loose.
@BigDog50001 3 жыл бұрын
👍
@theresahoffman8408 10 ай бұрын
Judging from the shiny studs , I'd say that rotor was removed for bearing assembly replacement. Hand held Impact Driver is the ticket
@forceuser609 2 жыл бұрын
I can't get the stupid screws off my tsx, tried all methods and air impacts
@user-tk1kj6ji2u Жыл бұрын
I have one of those Vessel screwdrivers, and one screw came off, but the other didn't. SUPER annoying.
@andreyv1 4 жыл бұрын
Hammered away at mine for a good 10 minutes with that exact screw driver and they didn't come out. What ended up doing the trick is drilling them out with a cobalt drill bit. Didn't put new ones in either because they're not necessary
@BigDog50001 4 жыл бұрын
Thanks for the input!
@sarahobrien3379 3 жыл бұрын
Does that turn as you hit it? Does it also tighten or does it not have a way to change the setting?
@BigDog50001 3 жыл бұрын
It turns (loosens) when it is hit. There are no settings and it will not turn the other direction (tighten).
@SkYxLeGaCY 3 жыл бұрын
02 Accord. Kinda a corolla guy myself though.
@dariuszszewczyk3106 6 ай бұрын
Ever heard about heat gun?
@BigDog50001 6 ай бұрын
Impacting works better than heat on these in my opinion.
@joet4806 Жыл бұрын
THANK YOU !!
@arthurfricchione8119 4 жыл бұрын
Dave, those vessel screwdrivers do they have JIS tips or are they just #2/3 Philips tips? Anyway, have a good cup of coffee and a Happy Thanksgiving. Artie 👍👍👍
@BigDog50001 4 жыл бұрын
They are JIS.
@chadfortman8098 Жыл бұрын
What pain in the ass on my Honda fit and pb blast last you can drill them out
@timhofstetter5654 Жыл бұрын
Is there really any good reason to have those screws in there? I think not.
@nosaj03 4 жыл бұрын
Would an impact driver work?
@BigDog50001 4 жыл бұрын
Yes, the tool I showed is a variation of an impact driver. I would just make sure to use a JIS tip.
@jondoe6926 3 жыл бұрын
Buy a 1/4 drill bit and #3 philips or the JIS. You may get lucky and you can get it out with the bit. If not, you have the drill. Smack the crap out of the screw before attempting. Don't listen to people who say all you need is the JIS. Not true. Screw can still break. There is no guaranteed way.
@mbs5328 4 жыл бұрын
How do we decide whether or not the rotors need to be replaced?
@cbarkwell1000 4 жыл бұрын
A Professional way is being in possession of the "Brake Specifications/Brake Bleeder Instructions Guide" from www.motors.com....The 2nd Step which will cause a large per centage of Mechanics to actually Blow a Head Gasket is using a "Micrometer & a Dial Indicator".........Utilizing those "2" Jewels by recording on every Customers Invoice will ALWAYS allow Judge Judy to side with you, ALWAYS - because of your EXCELLENT paperwork. Los Angeles County Southern California 11/21/2019
@BigDog50001 4 жыл бұрын
Basically, they should be replaced if they are scored, damaged or out of spec (parallelism/runout/disc thickness). Runout, disc thickness and parallelsim specs can be found in manufacturer service information and are generally measured with a dial gauge and micrometer. Sometimes rotors can be refinished on a brake lathe to bring them back into spec, but most shops now just replace rather than try to refinish them due to the cost of labor vs new rotors. In the case of Honda, if rotors are to be refinished, they generally only want it to be done using an on car brake lathe machine.
@kikeike5309 2 жыл бұрын
U re the best
@AntonioClaudioMichael 4 жыл бұрын
Good video
@BigDog50001 4 жыл бұрын
Thanks Antonio!
@joebush5463 4 жыл бұрын
i use a impact driver and big hammer 7 wacks only then its blue wrench time
@BigDog50001 4 жыл бұрын
A BFH is always helpful!
@califmike2003 3 жыл бұрын
No roto screws will allow slight movement of the rotors. I have heard leave them out if there broke and i have heard you need them to stop rotor play, i think honda put them there for a reason. Nice Video.
@BigDog50001 3 жыл бұрын
The screws only help during installation by holding them in place, once the wheels are torqued down the rotors aren't going anywhere. That being said, I don't like to install rotors without them.
@valvodka 3 жыл бұрын
a 2007 Accord and you make the video in 2019 and suggest the rotor is still factory?
@BigDog50001 3 жыл бұрын
You don't think it's possible? I guess you don't work on many vehicles. Thanks for stopping by.
@MrYapayepe 15 күн бұрын
Of how many pounds is your hammer ?🔨
@Dontcomplaincampaign 7 ай бұрын
My hand would of been broke in 4 places 😂
@BigDog50001 6 ай бұрын
lol
@BlackyBrownDestruction9337 2 жыл бұрын
Damn I bought a #2
@dandeleona4760 3 жыл бұрын
I watched this twice and noticed I hit thumbs down by accident the first time. So I changed it to thumbs up where it belongs. Sorry. :D
@BigDog50001 3 жыл бұрын
It happens sometimes, thanks for fixing it lol!
@b4w104 2 жыл бұрын
hmmm funny every Honda Ive worked on are so rusty cant even finf them barely
@coburn_karma 2 жыл бұрын
3:41 OUCH!!!!!!!😖😖😖😖😖😖😖😖
@BigDog50001 2 жыл бұрын
Yep.
@christopherminelli7593 4 жыл бұрын
Did you say you don't need to replace the screws? Why are they there, and why does the service manual not mention they are optional? Any idea?
@BigDog50001 4 жыл бұрын
They are there to hold the rotor during assembly, mostly for when they build the vehicle. Unfortunately, there are many things service manuals do not tell you. Other vehicle manufacturers use clips to hold the rotors in place and some don't use anything at all, even at the factory.
@christopherminelli7593 4 жыл бұрын
@@BigDog50001 Good to know, thank you!
@Jez2008UK 3 жыл бұрын
@@BigDog50001 So are you relying on the whole assembly keeping those rotors in place, sandwiched between pads, and held in place by a wheel and its wheel nuts?
@MAGA_USA 2 жыл бұрын
@@BigDog50001 Agree.
@ThePythonPit 3 жыл бұрын
I had a God awful seized screw. I bruised my hand something back with the hammer. It happens.
@jtsbasscovers4171 2 жыл бұрын
I hammered for hours and hours. Eventually tried drilling them out but my drill wasn’t powerful enough. I’m currently at a loss. On blaster, hammering, nothing works.
@Kevin-sy8uf Жыл бұрын
Damn, what did you get them out?
@dj5752 9 ай бұрын
Sorry. Shake and Brake
@jondoe6926 3 жыл бұрын
Yeah I don't get it. Half the people say it works, half the people say it doesn't do squat. Fuck it i'm just going to drill bit them out. No consensus on these things.
@victorrobinson7839 2 жыл бұрын
Number 3 what??
@BigDog50001 2 жыл бұрын
Those are tip sizes of cross-head (Phillips) screwdrivers, #1, #2, #3.....
@starguard4122 2 жыл бұрын
I was always under the impression that these screws were only put in place to hold the rotors on during time on the assembly line. Other than that, they serve no other purpose
@BigDog50001 2 жыл бұрын
They also help the same way when doing brake jobs. I always put them back (or replace them if damaged) on any Honda I work on.
@BigDog50001 4 жыл бұрын
Be sure to subscribe for more tool and car repair videos! kzfaq.info twitter.com/BigDog50001 instagram.com/bigdog50001/ Disclosure: This channel earns a small commission using some of these links - at no additional cost to you. The Big Dog 50001 Automotive Channel Store can be found here: www.amazon.com/shop/bigdog50001automotive
@masterofnone7846 Жыл бұрын
Heat around real quick!!Call it a day!Then leave it out!
@isrealcox1049 4 жыл бұрын
Man!! You are definitely the Man.. I mean ..forgive me Sir!! What I came to report is what your say is absolutely TRUE! So where can I go to find this vessel? Waiting Sir!...🙏🏿👊🏿👍🏿
Кушать Хочу
Рет қаралды 6 МЛН
Ultimate Handyman
Рет қаралды 15 МЛН
Garage 54
Рет қаралды 4,4 МЛН
EyeOnAiman
Рет қаралды 16 М.
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 4,4 МЛН
Vintage Engine Repairs
Рет қаралды 504 М.
CVR POV
Рет қаралды 854 М.