I was about 45 seconds and one more Z axis crash away from throwing my BL Touch against a wall, with my printer attached. No matter what info or reddit thread I found, nothing helped, then this video fixed EVERYTHING. THANK YOU SO MUCH!!!

This is the video I needed 3 months ago when I first got my B1 and got stuck with the lack of info fitting and setting up the sensor. Thank you!

Thank you so much!! I was struggling to get my BL touch to work (bed is warped). All the instructions and the software update I needed. you Sir are a star.

Great job, just another awesome video which is telling me it was the right decision for me to pick a biqu b1.

Dude, you are amazing. I really LOVE your attention to details. Thank you.

Thanks for the awesome video! After many attempts I finally got the ABL to work as it should!

Thank you a lot, finally got my Biqu B1 working with 3D Touch. Your guide worked like a charm!

This is great, and you do a class act on the various mods, with attention to detail. Being an absolute 3D printer beginner, I did a lot in terms of reviewing and researching the past week, as I am looking at buying this as my first 3D printer, over the Anet ET4 Pro, and definitely over the Creality Ender versions, I was also looking at. Now, I only need to buy some thingamabobs, doohickies (not the kiss and leave marks type), and lots of watchamcallits, also with lots of wiring, bolts, washers and nuts (maybe I am the nut), and a new metal shop with electrical hand tools. Then, I can mod this Biqu B1, before I level it and print my first, (what do you old timer 3D printer Types call it,) slice! This is all because, you had me at adding the BL Touch auto bed leveling thingee, on the end of your previous video on the B B1. Allow me to add my own conclusion; ................. Phew, I Am Now Exhausted just thinking about it, after I sat and watched the whole video! Wait, don't I need to print some parts, with different filaments for these mods to work, before I even think on doing this mod stuff, before I even bought the darn thing? Checks your links, and Groanz!

After watching this video I have to say that even though my printer is more heavily modded than yours, the fact that your mods look so professional made me want to start taking a lot of things apart and starting some mods from scratch. Your work looks really good and really detailed. Your 3d printer still looks clean after mods and that is not so common. Congratulations and thank you because you made me realize that a 3d printer doesn't have to look like a borg from star trek just because it has upgrades.

hey man!! thanks for that amazing video. greetings from Guatemala

Great Video... Exactly what I needed.. Thank You!!

Amazing what you can do with the right tools. Nice.

Very nice presentation!!!

Really great explanation. Thank you a lot.

Thank you so much for this great Video. It helps me to installed my 3D Touch in a few Minutes. ;) :)

Fantastic video. Thank you for taking the time to make and upload it. You should hit the manufacturer for some of the purple metal dye and anodise the parts you made, or am I getting a little OCD?

Thanks for the awesome video!

Great tutorial!! It looks like this is only true tutorial on how to instal and use bltouch on biqu b1. Thanks.

thx bro, u r really great

Thanks much appreciated.

Those are some good mods. I like the drag chains and the Love-joy style couplings for the Z axis screws. Do you have a link for those parts by chance? I also felt it was strange that the Z axis screws have no upper support bushing/bearing.

GREAT VIDEO !!! I installed the BLTOUCH on the stock BIQU B1 using the stock bracket provided with the printer. I can do the APL fine and then I can save it to the machine, but when I put the head at the HOME position it goes to the front left corner and not to the center. Marlin firmware is v2.06 AUG 24 2020 and screen firmware is NIGTREETECH_TFT35_B1_V3.0. Is there a need to update the firmware? If so, which one for BLTOUCH and stock bracket? Many thanks.

Thank you so much!!! You solved my bltouch issues! Loved your other mods as well! Can you please tell me where can I get the stl for the extruder knob at 8:00? Can you also tell me more about that filament sensor? All the best!

Probe offset would be nice to know for the bltouch mount

tnx it works nice

Great video. Can you provide the firmware.bin for the touchscreen and motherboard. Would really appreciate it

great video! What chain files are you usung?

thanks its very cool modifications , I Can't find Z-Axis Motor mod STL files . its very important .

Top usei aqui pois a cama ficava pra fora do bltouch

Thanks. Great guide. The only issue I am having is I have the all black version and the board is the SKR 2 rather than the SKR 1.4, so the provided firmware in the link does not work. I have the BL Touch installed and functioning with one exception. With the z axis stop disabled, my printer doesn't know to use the BL Touch to home the z axis. I am not familiar with the process of compiling the software myself to enable this. Does anyone know of anywhere I can find precompiled firmware for the BL Touch that works with the Biqu B1 SKR 2 board?

You so amazing

Good job, but did it stay anything from the original Biqu B1 printer??

do you have a firmware for skr 2 on biqu b1? I can't use my bltouch :(

Where did you get the BL touch mounting bracket??? I’ve been looking everywhere and can’t find them.

Im getting an issue, after I instaled the update, my printer freezes when I enter on the tf card, do you have the tft firmware to match with the software?

Are the steps similar for the micro probe?

my BLtocuh works now but it´s not probing the whole bed. is there a posibility to set the bed dimensions ?

Is the software here updated ? i have no ideea just got a biqu b1 and a BL touch :)), stock firmware does not have that setting

How I can uninstall the BIQU B1 - BL Touch enabled Firmware (Marlin v2.0.7)?

Hello fella, Im going to buy the b1 my first printer. I only want to add the bl touch, i Just need to make your steps or i Will need to change code on merlin?

Hey great video, I just installed the firmware,but I don’t know how to get to the screen at 5:33 in the video hopefully you can help me get to that. Thank you!!

Where i can get the dual z axis part?

This was a really cool video, but these modifications seem WAY too advanced for a beginner, as well as needing quite a bit of machinery or tools for most of these. For a beginner, would you say that you can find these parts pre-cut or pre-made anywhere for the B1? Or would it be easier for a beginner to upgrade the ender 3 v2? Trying to weigh my options before really getting into 3D printing, but I don't want to limit myself because I don't have a band saw, drills, crimpers, etc... Thanks!

Do you fool around with ender3 max. If yes how u like it. Run across ur channel and must say I like it. Sub up. Keep up great videos. From ur West Virginia hillbilly buddy stay safe

great video! My Biqu B1 does not have the z probe wizard selection on it. Not sure how to get this working. Anyone else have this problem?

will the bl touch work without downloading the firmware?

getting an error when I compile - Marlin\src\gcode\motion\G2_G3.cpp:157:7: error: 'MM_PER_ARC_SEGMENT' was not declared in this scope 157 | MM_PER_ARC_SEGMENT

I just bought the B1 SE Plus, I haven't yet received it but I'm just looking for upgrades for it. Not Many to be found it seems, it has auto bed leveling already installed as far as I know.., hopefully the organization and cooling mods many work

Any chance you could share the uncompiled configuration.h and configuration_adv.h files?

Did you purchase the drag chains and print the mounts? Could link to the exact chains you purchased?

I wish you a good day. Please help, I have the same printer and some languages are missing. How do I install the languages? Thank you in advance for your help.

after updating the firmware the printer says "NO PRINTER ATTACHED! can someone help me?

Why was the firmware modified?

Ugh. The lack of a SKR2.0 firmware that I can do this to is absolutely killing me :(

Brilliant commercial :P

Hi, I tried to flash the firmware of my B1, because I installed a BL Touch and this was not supported from the installed firmware. Unfortunately the printer gives this message out: "System loading, please wait" and nothing happens. Do you habe any idea how I can fix it? I wrote a request to Biqu, but they never answered. I have a Bigtreetech SKR 2 as mainboard and a BTT B1 TFT35 v3.0. Thank you in advance.

Can't finde the link to the firmware for BL toutch

👍

I have tried numerous ways to get it to install., but it prints in the air. It auto home's to the left-hand bottom corner by manufacturer default, so I can get a true Z offset. I may have a newer version of the printer as it it is all black. Mother Board is the SKV V2, with Marlin bugfix-2.0-7.2.x installed from the factory. Any help would be greatly appreciated.

Does the firmware work with the Skr2 board on the Biqu B1

Firmware flashing is definitely not working for me. It instead leaves me with a printer not detected message.

Can you put together a free energy device like a flywheel 12v generator that will generate enough power to power up a rv or a motorhome? If you will I be eternally grateful and if you won't blessings up on you anyways

oh my god! countersink the hole before cutting the thread please...

First