Stop saying "SIZE MATTERS"

Рет қаралды 294,563

Күн бұрын

A portion of this video was sponsored by Klarna
Get Klarna here: www.klarna.com/bitwit
_______________________________________
The new DAN Case A4 H2O builds upon the original, keeping a tiny footprint, but with extended hardware support for 240mm AIOs, triple slot GPUs and more. I assembled a high-end build inside of the new case to put it through its paces.
:+:+:TIME STAMPS:+:+:
00:00 - Old DAN Case vs. New DAN Case
5:02 - External Close-up Look
8:04 - Commence Build!
8:34 - AIO Installation
11:00 - Motherboard Mounting
14:09 - PSU & Wiring
18:57 - Cable Management Woes
20:37 - The GPU Dilemma
24:18 - GPU, At Last!
28:11 - Wrapping Up the Build
29:34 - First Boot! Maybe.
30:08 - DERP!
31:44 - Gaming Demo! System Performance + Temps
36:51 - Noise Test
37:21 - Final Thoughts
:+:+:STORE - BITWIT.TECH:+:+:
Our merch is extremely not awful:
:+:+:FOLLOW ME:+:+:
Twitch (I stream 3x/week): / wrkhrs3
WRKHRS3 Discord Invite Link: / discord
Instagram (Behind-the-scenes content): @bitwitkyle
Twitter (Personal updates, etc.): / bitwitkyle
MUSIC CREDITS
Epidemic Sound - www.epidemicsound.com

Пікірлер: 733

@sffbuilds5242 2 жыл бұрын

To be fair, a better-planned component selection would have made this a super clean build.

@DAN_Cases 2 жыл бұрын

True, useing a AIO with tubes come out the side of the pump, removing the bottom panel for cable management and do not route the 24pin through the same hole like the tube would do the trick :)

@kasper_429 2 жыл бұрын

You must be new here, lmao.

@Subdubbin 2 жыл бұрын

Not sure why he would use that AIO unless it was a sponsor agreement thing. Idk.

@PabzRoz 2 жыл бұрын

this case sucks

@kasper_429 2 жыл бұрын

@@Subdubbin Probably because it's the only one he had laying around that wasn't in a build, and he wanted to get this video out quickly, so he didn't tear down anything. Just my guess.

@JaredBusch 2 жыл бұрын

slick looking case! for me, the real trick with the cables is getting PSU's with sleeved cables. they're so much more flexible. to eat up cable length I create "S" shapes so that I can take as much or as little cable as needed while trying to reach pins and ports. with the AIO tubes, I usually twist the radiator (or pump) so that when installed, the tubes make a sort of cork screw shape, this allows the tubes to coil as you button everything up. it also forces the tubes one direction or another depending on your configuration, helpful for keeping tubes from pushing and putting too much pressure on the RAM sticks. ...and that concludes Jared's tech tips, goodnight everyone! lol

@RanenPo 2 жыл бұрын

Are you planning to pre-order the case, Jared? Also, any idea if it'll be available for pre-order in Canada?

@vux1236 2 жыл бұрын

Imma send this video to my girlfriend, thanks Kyle!

@xyner8834 2 жыл бұрын

Lmao

@PB24C 2 жыл бұрын

Lmfaaaooo

@DJCherry 2 жыл бұрын

Same lmao 😂

@davidbergman1719 2 жыл бұрын

What a legend

@rogosumania2574 2 жыл бұрын

i am going to send this to my non existent girlfriend

@brandonvictor4160 2 жыл бұрын

AIO with tubes that come straight off the face of the pump are kind of a no-no for a large majority of SFF builds. They just needlessly make things more complex than they have to be

@ensiel4738 2 жыл бұрын

What AIO was he using btw?

@Sarge-R1 Жыл бұрын

@@ensiel4738 Fractal Design Celsius S24 BKO

@DAN_Cases 2 жыл бұрын

Thank you for this build log video :) Some hints: - You can remove the bottom plate for much easier cable rounting on SFX-L - Route the 24pin over the bottom - Better use a AIO where the tubes comes out of the side not the top - Route the AIO tubes visualized in the manual

@ahoymateeez 2 жыл бұрын

Manual? Real men don't read manuals! xD

@SamNalty 2 жыл бұрын

Haven't you said before you had basically nothing to do with the creation of this case?

@techfreak244 2 жыл бұрын

@@ahoymateeezman-u-al? I never heard of such a word

@bralis2 2 жыл бұрын

@@techfreak244 Yap ... everyone means here a "womanual"

@techfreak244 2 жыл бұрын

@@bralis2 God I love when people get my sarcasm/humor

@drewmangan8542 2 жыл бұрын

I always recommend tuning your GPU and CPU voltages/clock speed. I have a mild OC on my 3090FE with a decent undervolt, and I have a -30 offset on my Ryzen 9 5900x which results in a sustained higher clockspeed, though this isn't OC'd. Doing SFF is always a bit more of a challenge, but it's well worth it if you like having desk space.

@futangclan 2 жыл бұрын

i have a -30 offset on my 5600x and an undervolted 3080 ftw3 in my nr200, temps are great.

@kyoudaiken 2 жыл бұрын

Any guide to undervolt Ampere? I am interested to push higher clocks with lower voltage. I am watercooling a 3090 STRIX OC with EKWB's Quantum Vector blocks, also the active backplate version. Temps are insanely low, but I want to push more performance cause it runs into the 480W power wall.

@Deqrypted 2 жыл бұрын

why blur out the “Radeon” Logo on your wall mounted pc ? just curious tbh

@NoGoodNoob 2 жыл бұрын

New GPU under NDA?

@milkonbean 2 жыл бұрын

Was thinking the same

@Adam1984_ 2 жыл бұрын

There's also blurring on the MSI logos on a couple X570 mobo boxes in the sponsor segment. Not sure why those would be blurred.

@FastSloth87 2 жыл бұрын

@@NoGoodNoob No, that's the waterblock that came with the EK-Quantum Power Kit, an all AMD watercooling thing they sent to reviewers last year (and you can buy for 900 USD!).

@P2PC 2 жыл бұрын

He took an Nvidia Sponsor probably or something along those lines. One part of a sponsor agreement can be to not show, indorse or mention competition or subsequent brand products.

@curtisskaufman 2 жыл бұрын

Thank you buddy, love your content and wanted to support the channel. Just picked up an Ensemble M desk mat. You helped me build my computer back in 2018. Keep going strong!

@chrislang7460 2 жыл бұрын

Well played. I've missed these styles of videos from you. Well played

@dylanguerrero8053 2 жыл бұрын

Glad to see you can kind of YOLO it while building in this case. Which means with some research and some custom cables you can make a pretty clean rig.

@stolenray 2 жыл бұрын

I like to do things the hard way: proceeds and builds in an A4-H2O without removing the bottom panel to help with the power cables routing....

@gypsy6211 2 жыл бұрын

I'm pushing a full loop with dual 240mm rads in an ncase M1. Someone mentioned component selection, that's Key to a clean, well fit SFF where there can be MM of clearance between equipment. Planning and research in advance is also important.

@QuantumBraced 2 жыл бұрын

4:08 I disagree, it is much bigger. If it's just going to be sitting on your desk, then the difference is not significant. But if you're going to be carrying it places (which the original A4-SFX was designed for), then it will make a big difference. You can't fit this new case in a backpack easily, it's much bulkier. The steel makes it heavier too. At this new size, there are better options imo. The NCase M1 being one, I'm glad I got mine before it got discontinued.

@mikerzisu9508 2 жыл бұрын

Cry

@dwhutto 2 жыл бұрын

Both my Formd T1 and my Ncase M1 fit into around the same backpacks, and it's due to the length more than anything. The difference between the original dan case and the c4 lengthwise is only 1mm. OG dan case is 326 and the h20 is 327. The Ncase is actually larger than the h20. Ncase is 338mm x 160.6mm x 255.5mm 12,7 L and the H20 is 244 x 140 x 326mm, 11,1L.

@Austin1990 2 жыл бұрын

Yes, that is significantly larger. But, it trades that for better compatibility. It is a great compliment to the original rather than a replacement.

@marioStortuga 2 жыл бұрын

That's what she said. (couldnt help it)

@yensteel 2 жыл бұрын

Both cases are very efficient in what they can fit. Some people like the term performance/litre as a metric. And both cases would be pretty high up there.

@tonylackie Жыл бұрын

Dude...I reminded to the beginning of this video about 4 times trying to hear the component specs! Only to find that you sprinkled it through out the build 😌

@Celician83 2 жыл бұрын

@Bitwit there is a hard setting on the Celicus coolers if you accidentally turned the cap on the pump, you switched it to quiet mode, which even with my brothers 2700x allows temps to get up to 75C

@sevezart 2 жыл бұрын

This has been a quite long awaited review. Thanks, Kyle!

@adamsteinbacher2629 2 жыл бұрын

So glad I picked the Hyte Revolt 3 for my SFF build. So easy, no riser cable, cable mgmt was simple, has practical handle that I actually use when moving around to different rooms.

@juliosalguero4638 Жыл бұрын

Same it's amazing.

@F83.M4 Жыл бұрын

This case is super easy to build in. Kyle is just an idiot who didn't spend more than 1 second thinking ab his part selection

@DontEatCream 2 жыл бұрын

SFF and "painful assembly process" goes hand in hand. After I put together my last rig in a FormDT1, I've decided that there is such a thing as "too small" and my next rig is probably gonna be in a NR200 or a Meshlicious case instead.

@slinkywizard 2 жыл бұрын

SFF doesn't have to be painful to build in, as long as you've got the right bits. I've got a Meshlicious (with 280mm EK AIO, 5800X, RTX 3070, SF750) and it was a very easy build process, far easier than this new Dan Case especially. For its size I think the Meshlicious is incredibly easy to build in, and still probably the easiest in the SFF class. I did employ the popular standoff mod (much like what Bitwit did in this vid, I used 2 x 20mm brass standoffs to raise the PCIE riser bracket for clearance for all my cabling through the middle of the case) which greatly improved my cable mgmt and getting a super clean end result. Highly recommended!

@grumpywolfgaming 2 жыл бұрын

Meshlicious is an amazing case, I'm using it with a 5900x and 2080ti and runs great.

@WW-tz6bg 2 жыл бұрын

NR200 is amazing.

@BlueLink56 2 жыл бұрын

Love the new case and the pricing is great for me. Thanks for doing a build video to show what I can put in the case.

@Aodan 2 жыл бұрын

Feels like they are moving closer to a slightly smaller NR200. I'm glad that I waited as I have a 3900x and wanted to go AIR in the NR200P, but may go with this instead as I have the same AIO already in an H200 case.

@seku_- 2 жыл бұрын

Why is the gpu blurred?

@gandalf6700 2 жыл бұрын

my best guess is Lyle Glued a picture of something nasty on it :) ´

@harold18427lol 2 жыл бұрын

"Not safe for work" XD

@tylermoore5659 2 жыл бұрын

Probably a branding issue

@swizzler8053 2 жыл бұрын

It's a 3090 TI.

@Bitwit 2 жыл бұрын

It was a request from the sponsoring brand. Probably too much hardware porn.

@jacobbrown8561 Жыл бұрын

Ty ty ty for THIS VIDEO. Can't wait to buy the bigger "Version 2". Thanks for (1)Side by side v1/v2 comparison (2)Pointing out 2x LONG rubber front/rear pads. (Better vibration dampening "?") (3)AIO/tubing sizings/Stand Offs $130 - $165 depends on GPU is fair! No price gouging. Unlike everyone 1.5 years ago.

@F83.M4 Жыл бұрын

There's no "bigger" version coming as there would be no point. This case already does it all without any compromise

@j.wandinger2944 2 жыл бұрын

Nice Case! Definitely an my top list. A little bit of research about the supported hardware would have solved all his problems.

@TheSlowpC 2 жыл бұрын

We need micro ATX cases !!!! Who’s going to make a new design supporting MATX and be small still.

@commanderoof4578 2 жыл бұрын

Well maybe at some point we could see an MATX with all the power delivery onboard as that would remove the power-supply size from the equation as their would be one Or at the very least onboard 12v to everything else with a gumbrick 12v only PSU

@JaredBusch 2 жыл бұрын

SAMA IM01 😉

@triliner254 2 жыл бұрын

I feel like a good matx case is redundant because matx motherboards are made to fill the cheaper end. There aren't much good matx boards.

@King_Jab 2 жыл бұрын

I think the price sounds a lot better. You can get an NR200p for $100-$120 so I see the cost difference for this as paying for it to be smaller.

@alanmacoisdealbhaigh 2 жыл бұрын

The blur on the RADEON badge on your water block at the start has me like O.o

@Techno-Tanuki 2 жыл бұрын

With modular power supplies, for ITX builds I normally connect the cable first then plug it into the PSU after managing the cable… but that might just be me.

@purplecrayon7281 2 жыл бұрын

Once you lay the PSU, there is no space for you to maneuver to access the connectors, even less so if the power cables are thick.

@jackbui2944 2 жыл бұрын

I do the same thing. It's easier to plug all the power cables into the motherboards before attaching it to the psu.

@nicholaseales 2 жыл бұрын

I'm done with riser cable cases, so for now my Ncase M1 is the ultimate SFF case with a normal config.

@CoalitionGaming 2 жыл бұрын

Doesn't that Fractal AIO have standard fittings? I suppose you could have changed the hoses out to something more manageable, but I suppose that also introduces other issues. Nice little build still!

@briangudiel9558 2 жыл бұрын

That wallmounted pc is badass! Also why s the logo of that ekwb waterblock for the radeon rx6800 and 6800xt and 6900xt blurred? and Nice Itx pc

@P2PC 2 жыл бұрын

He took an Nvidia sponsor probably, hence why competitors Such as Radeon weren’t mentioned and in this case blurred as part of an agreement for the sponsor. Only RTX products are shown too… seems fishy to me.

@wristonfroze6169 2 жыл бұрын

@@P2PC that’s normal if he’s sponsored, people sponsored by Samsung don’t touch or use iPhones in public at least because they’re not allowed to

@P2PC 2 жыл бұрын

@Casual Scum Pretty much. What were you expecting me to say?

@P2PC 2 жыл бұрын

@@wristonfroze6169 As if I didn’t already know that?

@wristonfroze6169 2 жыл бұрын

@@P2PC responded to the wrong person

@ghstbstr 2 жыл бұрын

That's a nice little pc so is mine... NZXT H1 case, Gigabyte X570 i Aorus Pro wifi, AMD Ryzen 3700X, Asus TUF RTX 3080 10gb, GSkill Trident Z 16gb 3200mhz cl14, WD 500gb blue sn550 m.2 nvme(boot and drivers), WD 4tb blue nand ssd(games), and a 120mm aio, 650w psu, gen4 riser cable(recall replacement) these last three came with the H1. My thermals... cpu 28c-32c idle, 46c-54c gaming and gpu 41c-55c idle, 60c-68c gaming.

@joshuaholliday1617 2 жыл бұрын

Kyle the kraken x53 aio has side mounted hoses on its AIO that are adjustable and would work perfect for this case

@katsumi656 2 жыл бұрын

Thanks, Dominic Cooper!

@BenyaminLorit 2 жыл бұрын

A disclaimer for first time small PC builders who happened into this video or doing research. A lot of the headache when building small PC's can be alleviated when you connect stuff first before mounting or screwing them. In big cases, you can just get away with sticking all the parts in and then connecting them later on but it's often the reverse when building small PC's. If you put parts in first before connecting your stuff, you'll find yourself squeezing your hands into uncomfortably tight crevices or be forced to remove stuff you've already screwed. So yeah, pre-route your cables and connect what needs to be connected before you mount and screw things into position.

@Killswitch1411 2 жыл бұрын

basically don't watch this as a how to build in this case.. Its how not too. Optimum Tech did it well.

@wilsyang 2 жыл бұрын

Isn't this case review supposed to release when pre-orders go live on February 9th.

@MiddleofKnowhere 2 жыл бұрын

Why was the Radeon GPU blurred out on the Wall-mounted PC?

@tomb3782 2 жыл бұрын

Man, look at the dust ring on the original Dan case. Dan 2.0 looks nice man. I wish it came in other colors though.

@Sproutt 8 ай бұрын

I dig the wall mounted 😂

@techjgboy8878 2 жыл бұрын

Love the video and the build

@Joe-wk9ow 2 жыл бұрын

One thing I would say would be great is custom cables. not for show but for optimal length.

@JexessXIII 2 жыл бұрын

Kyle, this video made me feel better about what I did this week. I built a PC for a customer at work and made a bet with a coworker that I would be able to get it to post on first try. I didn't. I found out during troubleshooting that the original issue was that I didn't push the GPU all the way in. Also found out that the Intel CPU was a KF series requiring the discrete card. I panicked when I pulled the card and the onboard graphics didn't work.

@psphacker57 2 жыл бұрын

God that RGB build in the background still looks beautiful

@Croaker369 2 жыл бұрын

Please leave your captions on a little bit longer so they can be read in full.

@MarioP495 2 жыл бұрын

You gotta get some right angle adapters or something for those cables on the wall mounted PC

@PadawanPreacher 2 жыл бұрын

I was waiting on the Barnacules "ladies..." at the end of that intro lol

@VolcanoPenguin 2 жыл бұрын

That add was top notch 👌

@joseph_p 2 жыл бұрын

It’s honestly a fair bit bigger, but if you need the performance, or want to keep your build quiet it is definitely worth the size increase.

@jakobfindlay4136 2 жыл бұрын

i loved the style of the dan case so much i tried to make my own but bigger never finished the cad :/

@lumi_arcs 2 жыл бұрын

19:54 pro tip. remove the AIO Bracket and pull it up a it. Hoses should be long enough to do that. then you would not have the problem with the power cable pass-through?

@Techno-Tanuki 2 жыл бұрын

I miss my small formfactor system. Sadly the tu150 was suffocating my 3080 and fans wouldn’t fit under it. Even super slim ones.

@christopherkirbo529 2 жыл бұрын

The price is pretty good for the quality shown in this video. I really like that they threw in a triple slot, and I love SFF PC's but I wish there was an in-between sized case. SFF is often too small, and mid towers are considerably bigger. I want an SFF+ that supports two 240mm/280mm radiators and fans so you can watercool the 12900K (once a good mobo supports it) and a 3090/4090 or a 6900xt.

@lanon3277 2 жыл бұрын

It's called an M-ATX (micro-atx). You may also be interested in the NR200p.

@christopherkirbo529 2 жыл бұрын

@@lanon3277 Wow, thanks! I've known about these but never even thought to consider one because I cannot stand the way the Micro ATX Mobos look, but with the size I'm looking for I might just consider going with a no glass case.

@VanityVazKez2534 Жыл бұрын

lmao that sponsored skit was pretty smooth.

@Ladue52 7 ай бұрын

If you would have used 90 degree adjustable hoses it would have made the build 20x more clean looking, but still very helpful in helping me find parts for my A4 that I will be getting.

@Big-Critic 2 жыл бұрын

Why is the GPU on your wall mounted PC blurred out?

@Clutch_Gameplays 2 жыл бұрын

Hey Kyle, why was the Radeon logo blurred out?

@oleg_aka_djmeg 2 жыл бұрын

Yeah definitely don't bend the tubes like that. I had my NZXT X61 tubes bent in a similar way but not that tight and one day one of the tubes just cracked and all the coolant leaked out.

@davidchillton1744 2 жыл бұрын

Or just don’t do water cooling

@oleg_aka_djmeg 2 жыл бұрын

@@davidchillton1744 that's kinda the point of the case though. there are a lot of AIOs with adjustable tubes that come out from the side of the block, it would be much preferred to use these in this case.

@kyoudaiken 2 жыл бұрын

@@davidchillton1744 I agree that good air coolers perform the same compared to even the best AiO CLCs out there, but it just won't fit inside this case. To cool a 5900X without an AiO in this case, going custom is the only way. If you got a 5950X, custom liquid cooling is mandatory.

@masonconnor7356 2 жыл бұрын

@@kyoudaiken well he probably couldnt use an air cooler cause theres no space for air to flow well in there without any cooler outright

@martythestines 2 жыл бұрын

1:30 I used to get that all the time with my mom. I'm sure that happens less with our kids since we know the struggle. I'm 32 and my 2 year old son, won't have that issue with me. I started playing online with the Dreamcast, but shortly after, the OG Xbox.... since... you know... The Dreamcast died young.... By the time our grandkids are old enough, we'll live in the "Metaverse" or the Matrix. Maybe Wreckit Ralph Land...

@khyron6 2 жыл бұрын

Looks Great, But I still have to put a custom handle on it. Great video, Thanks. :)

@tyrantdirector 2 жыл бұрын

Why did you blur the GPU in your wall build???

@homi1001 2 жыл бұрын

Why was the "Radeon" Logo in the beginning censored?

@Jraz1011 2 жыл бұрын

It looks like a swastika when spinning

@homi1001 2 жыл бұрын

@@Jraz1011 Nope that is wrong, because the card shown in the video is the special waterblock that was sendt to content creators, but only the standard air cooler would show up as sawstikas while spinning at a certain refresh rate.

@Naturalhighz 2 жыл бұрын

I mean you can still use a newer gpu with a gen 3 riser cable, you just need to set the pci port to gen 3 in the bios.

@Just_Ben_YT 2 жыл бұрын

6:50 not a placebo effect, if there's more rubber on the desk then it'll grip better

@ktyler90kt 2 жыл бұрын

150-180 U$D is VERY competitive since I bought a Lian Li Gen 4.0 PCIe riser cable from Amazon for $85. It is very HIGH quality and have tested very well with it on my 6900Xt Blue Devil [U] since December 2021👌. I'm happy with Lian Li so far.

@CimInc 2 жыл бұрын

Wish they'd made it just slightly wider, to also support 280mm rads. But looks very interesting other than that.

@satchef1 2 жыл бұрын

It would need to be 20mm wider and 42mm longer, for a total increase in volume of 2.1L. Adding 280mm compatibility would allow for four slot GPU support and/or better air cooler support. But in most typical configurations there would be a lot of dead space. The upcoming C4 supports 280mm. Tower layout seems more space-efficient for that rad size.

@arazan 2 жыл бұрын

@Bitwit why did you blur the Radeon logo at the beginning of the video?

@P2PC 2 жыл бұрын

Maybe Nvidia sponsored?? I’m not sure to be honest.

@yensteel 2 жыл бұрын

Have you considered reviewing the FormD T1 before? You might like it. It's between the size of the Dan A4 and A4 h20 and could juust fit a 240mm rad with slim fans, and could fit a 3 slot card (but you will need to make sure the AIO block isn't too tall).

@yensteel 2 жыл бұрын

@@user-op8fg3ny3j You're right, the 1.1 version is discontinued. They're accepting orders for 2.0 now. There's a sandwich and a M1 styled version. Both are the same size at 10L.

@matasa7463 2 жыл бұрын

I think undervolting will give it much better GPU performance. My GPU hits around 1905 MHz at only around 240W.

@eaaeeeea 2 жыл бұрын

This case will end my over a year long wait for a new PC, as my 3-slot 3080 just arrived. I hope it ships fast.

@literofcola6628 2 жыл бұрын

Hold up. Why is the Raedon logo on the GPU blurred out of your wall mounted PC?

@P2PC 2 жыл бұрын

My theory is that Nvidia must have sponsored the video, hence the lack of mention of Radeon or such. I may be wrong tho but thats my two cents.

@RealArexz 2 жыл бұрын

I would actually prefer the Nylon standoffs for this purpose, because you want the standoffs to break before your PCI-e cable/port.

@GR-cd2kx 2 жыл бұрын

If the rad fans are sketchy and could rub cables/hoses, can they go on the other side of the radiator so the fans pull air through the rad?

@sabasgutierrez3781 2 жыл бұрын

Hello, Quick question, how did you power your itx system on your dual system setup on the phantek 719 case?

@DaltonP386 2 жыл бұрын

I actually had a Dan case v3, but my ribbon cable took a poop so I completely left the riser cable scene.

@mm8tech370 2 жыл бұрын

kinda confused as to why the radeon logo was blurred at the beginning

@PsychoKern 2 жыл бұрын

Good things come in small packages

@keibohow69 2 жыл бұрын

You should of put the other gpu in? That would have been fun to watch. That case might be better in a vertical position.

@xenonbrawler007 2 жыл бұрын

Am I the only one that noticed the blurred out Radeon on his wall pc?

@AndyTrucker1985 2 жыл бұрын

I just built in the lian li q58 talk about an amazing well thought out small form factor case

@maubreydelrosario2712 2 жыл бұрын

miss youu man. hope youre safe there or wherever yo are.

@alexbranton5975 2 жыл бұрын

I know this is a long shot but I’ve got the same mb. I can’t build anymore until I remove the 2 brackets for the cooler however one of the screws is completely stuck. Using the right tool the other 3 came off no problem however the last screw will not budge. Any tips?

@JoeLeasure 2 жыл бұрын

Gah, no one takes this thing completely apart! I'm dying to see those panels on either side of the aio come off. Do they? I don't know!

@JoeLeasure 2 жыл бұрын

I'd love to see this case with a hybrid gpu and a 120 on the cpu. Great vid though.

@craigfoy8674 2 жыл бұрын

whats the deal with radeon being blurred out?

@SleepyRulu 2 жыл бұрын

This should give me confidence put similar hardware on my rz0b2 silverstone

@robertosalazar3476 2 жыл бұрын

Why was he blurring out the Radeon logo in the beginning from his mounted rig?

@matttran7161 2 жыл бұрын

Man the middle market is starving right now, we need sandwich style cases to come down to the $100-150 range. Right now "affordable" ITX options are the Silverstone SG13 ($60ish), the Cooler Master NR200(P)($100), a handful of AliExpress/Taobao suss options, and that's about it. I love the look of the Thorzone Mjolnir, but not the $300 price and months long wait.

@Alucard0715 2 жыл бұрын

I'm curious about the blurring of the Radeon logo on the water block of the wall mounted PC.

@P2PC 2 жыл бұрын

I’m not sure either, maybe Nvidia sponsored the video in some way, hence the lack of mention for AMD or Radeon through the video. I could be wrong though.

@ellisongreene3259 2 жыл бұрын

The intro felt like a pov real estate agent video

@joshharrow9219 2 жыл бұрын

Could have rotated the aio so the tubes come out on the opposite side instead of your psy side so more space for cable routing

@theewunandonly 2 жыл бұрын

What Radeon card was blurred out in the intro?

@Mike_Hogsheart 2 жыл бұрын

As somebody who owns an original A4 (not even the v2 with official water cooling support), I can say that I'm very happy with my case and would 100% purchase it again over the new version. I run a 120mm AIO and an ITX GPU in mine, temps are perfectly fine as is so I see no reason to compromise on the one defining feature that makes the case as awesome as it is. A 50% increase in volume is just too much, imo.

@scarkillerful Жыл бұрын

Are you ignoring that new GPUs are fucking huge and that new CPUs are pulling insane amounts of power? The whole point of the new case is to provide hardware compatibility with the latest and greatest components, and as such to not compromise on performance. With the old case however, it's compromising on performance. A 120mm AIO just isn't going to cut it anymore, and good luck finding a SFF GPU in this day and age. They don't exist for current top end hardware. It's just unrealistic. If you don't want top end hardware, fine. But a lot of other people do. A 50% volume increase is welcome ;)

@geoffrymouser7031 2 жыл бұрын

The more sff cases get released, the more I appreciate my nr200. Can fit a 280 rad to cool my 5900x with plenty of room for my 3070. To me, the price difference isn't worth the

@ghstbstr 2 жыл бұрын

I want a nr200p max but they aren't sold anymore it seems, and that sucks because I really want that case and included components. I'm not happy about that.

@heatnup6899 2 жыл бұрын

@@ghstbstrI know I’m late but just in case you see this and didn’t know they are still sold, not on cooler masters website but on Amazon and Newegg

@garforce2 2 жыл бұрын

why was the rgb logo on the wall mounted GPU blurred out? is it because this video isnt sponsored by them or that you didnt use that brand?

@hanshenrik9870 2 жыл бұрын

The struggles of SFX's 😄. Nice to see a new SFX cabinet. Still rocking the NCase M1 myself.

@iswandee1983 2 жыл бұрын

You can tell that kyle has very little exp with sff build . With proper planning , this build would have been easy and super clean. Optimum tech would have made this look like a child's play..hahah

@Killswitch1411 2 жыл бұрын

I agree, Kyle is out of his element with SFF Optimum Tech did a bit more research and planed it... Kyle just idk haha.