No video
Blank black Screen fix HP 23 Envy AIO PC corrupt bios repair Arduino flash
Рет қаралды 58,976
Күн бұрын
@shaydjohnson5725 4 жыл бұрын
This comment is for the folks watching in hopes of finding a clue as to what's up and how to fix their machine and is not intended as a bash or derogatory comment at the video's creator. At 1:08, you say you should have assumed it wasn't the inverter. Actually, you should have known that much earlier. There was no hard drive LED activity showing a drive booting, no beeping during the POST, and no keyboard lights showing or even callable by pressing Num Lock, Caps Lock, etc.. If it was a simple matter of a bad inverter, the rest of the machine would function as usual. Nice work on the BIOS recovery by the way.
@michaelshrader5139 4 жыл бұрын
Same model computer, but with i7 processor... turns on fully maybe 10% of the time and works correctly. But if the power goes out or you shut it down by accident, it can take hours of turning it on/off before the HP logo will finally appear and Windows 10 then boots up. I'm figuring the board has gone flakey (checked all connectors pulled and replaced memory etc), seen it happen on other AiO computers by Dell, Lenovo, Pick-Ur-Poisen! They just don't make 'em like they used to. On the hunt for a good working take-out motherboard now or will recycle it if I get tired of searching. Personally, I have 2 Lenovo A730 AiO computers with 27" Quad HD Touchscreens and love these things (both are used/parts only computers I rebuilt, off Ebay for less than $200 each after acquiring needed replacement parts). Regards!
@OthmanAlikhan 6 жыл бұрын
Thanks for making the video despite the jittery camera and video quality. It was very useful. I am in a similar situation where my BIOS ROM is corrupt and need to re-write its contents. I really appreciate the effort you went to put this video up =)
@kennethpappas 5 жыл бұрын
hi buddy. i get a light where i plug in the power cord but at the switch i get no light. any advice as to where might be the problem?
@abnad2827 2 жыл бұрын
👍 👍 👍 Good vidéo Please I'm looking for bios to my hp envy 23 recline k110 ef, the screen is black after power on. I think the bios is corrupted. Thanks in advance for helping me.
@chacomputer1 6 жыл бұрын
just wanted you to know I thought you did a very good job on fixing the HP I really enjoyed your video
@buddygreer8482 4 жыл бұрын
Great vid! Looks similar to what I am experiencing. I have blank screen, no beep codes, and usb ports don't work. I think I need to do this even if it the motherboard is bad, so I can grab the windows product key stored in the bios. Were you able to recover the windows key? If so, how? Thanks again. Cheers!
@bigslick 4 жыл бұрын
No, you cant recover the Windows key from a corrupt bios, this data is corrupt by definition.
@vanveenster 7 жыл бұрын
Congrats and thanks for linking to my site :D!
@castellon69 4 жыл бұрын
It worked, thanks. excellent video. Gracias.
@ilyasjaweed1286 3 жыл бұрын
Hi, I recently experienced the same problem. Is there any other way to get it fix as im not good @ IT stuff. When u said issue command I didn’t got it how to give commands in linux. I got exactly same issue. Power on only fan and dvd turns on. No keyboard lights, no boot up.
@chudzoskruo 6 жыл бұрын
If I understand well bios battery need to be removed before process? as you did mention at the end you need to give it back. And if I may know how did you find out and was so sure it is bios problem? I think there could be tons of failures which can lead to black screen, or am I wrong somewhere?
@jangnahal6701 5 жыл бұрын
From where i can get new BIOS for this motherboard
@29sigus 6 жыл бұрын
So I have an envy 23, I turn on my Hp computer than the screen lights BOOM the screen stays black for the rest of time, I’m commenting this mid video so could you answer my question so I can go back on my computer, Thank you.
@alfatech8604 2 жыл бұрын
How did you make the arduino able to flash
@IAmYakYakTV 4 жыл бұрын
Good sh*t bro...ill be following this to fix mine. What Aduini board do u suggest if not for the one ur using?
@brian-bi9qz 2 жыл бұрын
Hai , can I know my all in one hp pc can do this ?
@DaveAH01 6 жыл бұрын
Using the exact same Arduino board, and the same HP ENVY 23, I'm getting the following error message: Error cannot synchronize protocol- check communications and reset device? *Note, when I try to use the 5V output from the board, I lose connectivity to the Arduino, but if I use the 3.3V, the board shows up (but then shows me that error). Any suggestions?
@nazifkhan8252 7 ай бұрын
Can u say jumper connection???
@zbbo1676 5 жыл бұрын
how do you know bios problem? there are tons of devices can cause the black screen.
@spiiido 5 жыл бұрын
Hi, is anyone there who can tell me how to connect the arduino to the pin's on the motherboard of the computer? What is the correct wiring? Wich Pin of Arduino Board has to be connected to with pin on the compters motherboard to get it work?
@konsul2006 6 жыл бұрын
Eevblog2 needs your help :) - Dumpster-dive-pc like this, with a black screen issue.
@bigslick 6 жыл бұрын
very cool. Yeah, I used to watch Dave's videos a long time ago, probably around 2008-2009. He does an awesome job.
@rogerbryan444 6 жыл бұрын
Hello sir, can you help me use the exact same Arduino board to save my dell xps 2710? Very good video. I would be grateful if you help me save my xps 2710 black screen. thank you in advance
@bigslick 6 жыл бұрын
Hi, thanks for the kind words, but unfortunately I have no experience with trying this procedure on a Dell. I would hazard a guess that if your mainboard has the same header that you see in this video, then I see no reason why the general process would be any different (of course, using your correct bios for your Dell). But if your mainboard has a different (or missing) header, then you may have search around for another solution.
@mbelsky 4 жыл бұрын
Hey Bigslick. I am trying to repair an HP Envy 23-o014 - all-in-one that wont boot after a failed bios update. It goes to the HP screen and then eventually says "Press the esc key for startup menu". I have tried guessing at CMOS reset pins, removing CMOS battery, booting from USB to reflash (cant because cant even get to boot menu). I wanted to try your reflash method and have the arduino and all parts, but I cannot figure out which pins are which. My PC does not have a seperate labelled ROM recovery section. I am uessing I need to use the 8 pins that are near the CMOS battery, but they are not labelled beyonf numbers 1-8. Do you know if I am correct that I need to use theses PINs? I cannot find any documentation on the motherboard to figure out which pins are which. The only info on the board that I see is DAONZDMB6E0 REV:E and Model: NZD The board I have is pictured here: www.newegg.com/p/1JW-000M-00HB3 If you are at all inclined to help, it would be very much appreciated, either here or via email. errorhelp at gm@il dot c0m
@mbelsky 4 жыл бұрын
In the end I was able to fix it using the following: amazon.com/gp/product/B07R5LPTYM/ This one has better reviews mostly regarding build quility, so I'd get this one if not in a huge rush: amazon.com/gp/product/B07SHSL9X9/ I just couldn't wait the extra week or so.
@sheilakhan5748 7 жыл бұрын
Thank you for this video. How do you confirm that the Arduino is being picked up by the Ubuntu laptop? Also, I noticed you didn't use a Raspberry Pi as specified in the website/post by Marcus.... is using the laptop an easier/better way?
@bigslick 7 жыл бұрын
1) The Raspberry Pi is WAY WAY overthinking the situation and unnecessary device for fixing your HP pc. All a Raspberry Pi is...is a cheap underpowered Linux computer. If you already own another PC, just run Linux from that. Since I had an old laptop and a spare HD, I just installed Linux on it. You could do the same with any older PC, desktop or laptop, but a laptop is convenient because you can easily carry it to the HP you need to fix. 2) When you start issuing the commands from " ls -l dev/ttyACM0 " and down in my list from the NOTES section above..., if the Arduino has not been recognized by Linux yet, you would get an error message on the command line from Linux. Be advised that this is a VERY geeky project. It will be difficult for anyone without basic Linux experience, or someone who had never worked with other command line interfaces, such as MS-DOS or vintage computers (such as a C64, TI-99/4A, or other early computers that required command-line control to accomplish a task).
@stoneschanify 7 жыл бұрын
Thanks. Thats exactly what I thought. It just makes it more work having to install and prep a Rpi. I have a thinkpad running ubuntu mate but some of your commands are giving an error. I just rebooted the laptop and will report back shortly. I would appreciate any help you could provide. Thanks.
@stoneschanify 7 жыл бұрын
Here's the first command that throws an error. When I run as sudo I get a seperate error which Ill post as well. Thanks for all your help in advance: anthony@anthony-thinkpad:~/frser-duino$ make u2 && make flash-u2 make clean make[1]: Entering directory '/home/anthony/frser-duino' rm -f frser-duino.bin rm -f frser-duino.out rm: cannot remove 'frser-duino.out': Permission denied Makefile:74: recipe for target 'clean' failed make[1]: *** [clean] Error 1 make[1]: Leaving directory '/home/anthony/frser-duino' Makefile:86: recipe for target 'u2' failed make: *** [u2] Error 2 anthony@anthony-thinkpad:~/frser-duino$
@stoneschanify 7 жыл бұрын
When ran as SUDO: anthony@anthony-thinkpad:~/frser-duino$ sudo make u2 && make flash-u2 [sudo] password for anthony: make clean make[1]: Entering directory '/home/anthony/frser-duino' rm -f frser-duino.bin rm -f frser-duino.out rm -f frser-duino.hex rm -f frser-duino.s rm -f *.o make[1]: Leaving directory '/home/anthony/frser-duino' DFLAGS= FRBAUD=115200 make all make[1]: Entering directory '/home/anthony/frser-duino' avr-gcc -mmcu=atmega328p -DBAUD=115200 -Os -fno-inline-small-functions -fno-tree-switch-conversion -frename-registers -g -Wall -W -pipe -flto -fwhole-program -std=gnu99 -Ilibfrser -std=gnu99 -I. -o frser-duino.out main.c uart.c spihw.c libfrser/frser.c libfrser/udelay.c libfrser/spilib.c libfrser/spihw_avrspi.c avr-size frser-duino.out text data bss dec hex filename 1426 0 1036 2462 99e frser-duino.out make[1]: Leaving directory '/home/anthony/frser-duino' BLBAUD=115200 SERIAL_DEV=/dev/ttyACM0 make program make[1]: Entering directory '/home/anthony/frser-duino' avr-objcopy -j .text -j .data -O ihex frser-duino.out frser-duino.hex avr-objcopy:frser-duino.hex: Permission denied Makefile:56: recipe for target 'frser-duino.hex' failed make[1]: *** [frser-duino.hex] Error 1 make[1]: Leaving directory '/home/anthony/frser-duino' Makefile:90: recipe for target 'flash-u2' failed make: *** [flash-u2] Error 2
@stoneschanify 7 жыл бұрын
Another thing, when I plug everything up to the ROM pins on the HP envy and finally plug the Arduino into the USB for power the LED on the motherboard lights up for a split second and then shuts off... any idea whats causing this also? Do you have to use a separate wall power to power the Arduino or would USB be suffice? I followed your way as you suggested instead of doing all of the RPi stuff.
@bigslick 7 жыл бұрын
The 2nd product link that I provided is for a power pack that powers the Arduino, so yes... the Arduino needs a separate power pack. It is NOT usb powered.
@philipfinlaw2298 6 жыл бұрын
I have an HP that is also showing a blank screen but when I turn on the power button I hear it booting up, even getting the windows startup sounds. If it's truly booting up but not displaying video, then BIOS would not be the issue correct?
@bigslick 6 жыл бұрын
If you are sure that windows is booting, then the bios is fine as far as I can think... so you probably have a hardware problem. Check the lcd inverter board -- a cheap option to try and easy to replace.
@stoneschanify 7 жыл бұрын
I'm up to this part. Everything is connected... and I can see the Arduino is connected using ls -l /dev/ttyACM0 however I get the following when trying to read/save the old ROM: anthony@anthony-thinkpad:~$ sudo flashrom -p serprog:dev=/dev/ttyACM0:115200 -r OLD.ROM flashrom v0.9.9-r1954 on Linux 4.10.0-19-generic (i686) flashrom is free software, get the source code at flashrom.org Calibrating delay loop... delay loop is unreliable, trying to continue OK. Error: cannot synchronize protocol - check communications and reset device? Error: Programmer initialization failed. Could you help me out with this part? Thanks.
@stoneschanify 7 жыл бұрын
Bigslick, any idea what this error means? Calibrating delay loop... delay loop is unreliable, trying to continue OK. serprog: Programmer name is "frser-duino" serprog: requested mapping AT45CS1282 is incompatible: 0x1080000 bytes at 0xfef80000. No EEPROM/flash device found. Note: flashrom can never write if the flash chip isn't found automatically. anthony@anthony-thinkpad:~$ I went ahead and connected a wall power supply to the Arduino. This is where I'm stuck now. Seems like I am getting closer so any help is appreciated.
@stoneschanify 7 жыл бұрын
Never mind. For anyone else getting the above here... play with your jumper cables... Seems like i had to remove mine completely.
@leo25pz 7 жыл бұрын
What I would of had done is look for the latest bios update and install it to the flash drive. Remove the cmos battery first and let it sit for 2 whole minutes, then put cmos battery back and boot to bios select boot manager or boot order and select usb key first in boot order and it will flash the bios at next bootup. If the computer does not boot then I would attempt to use a jumper.
@bigslick 7 жыл бұрын
That does not work with this problem, which is why the video exists in the first place. In other words, the failsafe bios recovery is corrupted. Thus, the need for remote flashing.
@joelzapanta6932 7 жыл бұрын
I had the same problem.
@IAmYakYakTV 4 жыл бұрын
your 2nd amazon link is broke.
@bigslick 4 жыл бұрын
fixed
@raytrimble5013 5 жыл бұрын
Crap two of the links are no longer good.
@MrPureblaque100 6 жыл бұрын
Do you do repairs and can I ship
@bigslick 6 жыл бұрын
thanks for asking, but I only fix this kind of stuff for myself, not as a business.
@bobbauvian7700 5 жыл бұрын
I just bought 1 for $20 from the pawn shop too. lol.
@carlossamir5499 5 жыл бұрын
You should take the bios out of the motherboard erase the old file you get the new file reprogram the chip than put it back to the motherboard this is not the professional way use Eprom programmer 5.5 🤞😎
@bigslick 5 жыл бұрын
asinine.
Wondershare Recoverit Data Recovery
Рет қаралды 1,2 МЛН
Tech Argon
Рет қаралды 1,9 МЛН
It's Binh (Been) Repaired & Everything Reviewed
Рет қаралды 38 М.