Complete DCC install using a Nixtrainz Decoder Buddy Mini, Scale Sound Systems speakers, A TCS WOWSteam decoder and a TCS KA4 Keep Alive.
Пікірлер: 18
@gwmccoy3 жыл бұрын
I think this needs to be said: Between your "everything included" tutorials, J.T.'s speakers, and Nick Santos' decoder buddies, I have learned about some products and techniques that enabled me to attempt and successfully complete DCC Sound installations that I would not have attempted not that long ago. Thank you very much for these, Larry...keep 'em coming!
@usacitizen10002 жыл бұрын
I've got one of these BLI engines in the Erie roadname with the square tender. I would like to convert it into a C&O engine with a vandy tender ,...and that sound system.
@usacitizen10002 жыл бұрын
I just watched some of your videos that were posted in MRH forum. I am impressed with you presentation, CAMERA work, and knowledge. I plan on revisiting with I hopefully get to experimenting a little this winter after the lower level of my new layout becomes operational. My location in northern FL should present real good weather for this experimentation to take place on my carport work bench just outside the train shed. While all the northern's get snowed in, I will be enjoying our nice cool weather.,...and hopefully learning about DCC/sound installs in my fleet of larger steam engines. Brian
@markmatteo24176 ай бұрын
I've had 2 of these short out in a couple of days. They're a few years old a couple of 4-8-4 T1's. I didn't have a whole lot of hours on them. Are these known to have a lot of problems? It kinda seems like it. Thanks
@hartmutlorentzen96593 жыл бұрын
Grand video, mais beaucoup de travail et quelques risques. Merci
@paulpietrowski19403 жыл бұрын
I've learned a lot after this one, and definitely need a smoke and a drink lol. Keep it going , great job...
@kylestevens69253 жыл бұрын
Another great video man, i really need to work on my greenbrier someday and learn this stuff. Thanks for sharing.
@parker.craig232 ай бұрын
7:38 excuse me what model of calipers are these?
@SoloContracting2 ай бұрын
www.shars.com/aventor-8-ip67-electronic-caliper
@eXtremeFX2010 Жыл бұрын
I have almost the exact same style locomotive from Bachmann except its a 2-10-0 HOWEVER...I am having trouble getting the front face boiler off to swap out the light for an LED. If I am not careful could break its delicate build.... QUESTION: Does ESU have a true NON-LED Light Mode for Light 0?
@SoloContracting Жыл бұрын
When you go to program the decoder, don't check the led mode box for the lighting function. Remember to put a resistor in or you'll need to remove the shell, to fix the light.
@eXtremeFX2010 Жыл бұрын
@@SoloContracting Thanks so much for the reminder... I had actually thought about as well. My other Bachmann Steamer DCC conversion I dropped in SoundTraxx TSUNAMI2 TSU-BH2 and had absolutely no issues with LEDs or forward headlams..Headlamp... the decoder made adjustments. The only reason I didn't go with it here, ESU had the correct Sound file for 2-10-0 where as TSU-BH2 did Not have an exact match but just a close enough match.
@gmpullman2 жыл бұрын
See that screw that holds "PCB02" to the frame? It is the way the right drivers convey the current to the PC board. I've had a few BLI locos where there has been slight corrosion there along with the coating material BLI uses to "blacken" the frame. My suggestion to anyone having a BLI steam loco disassembled this far is to make sure that threaded boss is filed clean and there is no corrosion on the screw and the solder "eye" of the PC board is making good contact here. A tiny dab of No-Ox-Ide might be good, too.
@markmatteo24176 ай бұрын
Is that a standard JST plug on the tender ?
@SoloContracting6 ай бұрын
It is the factory jst connector. These can be had through sources such as Digikey. It would need to be measured to get the correct one. You can do that by measuring the distance from the center of one pin to the center of another.
@markmatteo24176 ай бұрын
Mine one wire pulled out. Not sure how to fix it. Is it worth just hardwiring it?@@SoloContracting
@SoloContracting6 ай бұрын
They can be repaired with the right crimper. You can also pull out the old wire from the connector and replace it with this part from Digi-key. 455-3076-ND
@karlmuller18543 жыл бұрын
Hi, I don`t quite understand what you where trying to accomplish with this build. I just did a BLI 4-8-4 with Loksuond 5. I used the 32mm speakers in the tender but build 15mm speaker enclosures with .5mm styrene. Used a Seuthe 100 (with cables) for smoke in the boiler, that things smokes up a storm. I kept the full weight in the boiler. The engine is so loud I could call together the neighborhood with it.