BMW 2004-2010 X3 Transfer Case Actuator & Fluid Replacement DIY (BMW E83 X3, 2004-2014 X5, 08-14 X6)

Рет қаралды 190,907

Күн бұрын

►No matter how well the xDrive system was designed, the BMW X3 transfer case actuators do fail and will need to be serviced or replaced.
There are a few BMW X3 transfer case symptoms you might notice when it begins to fail. One of the first and most glaringly obvious signs is if you've noticed the 4x4, ABS, brake, or all three symbols illuminate on your dash; this could be a sign that your transfer case actuator gears are starting to fail. Another symptom that's less obvious is that you may also hear a clicking noise when putting the transmission in gear.
In this video, Mike Hidalgo doesn't just replace the transfer case actuator gears, he begins by replacing the transfer case fluid. We recommend using only BMW transfer case fluid (DTF1) which you can find here: www.fcpeuro.com/products/bmw-...
After this job is complete, you're going to want to have the BMW X3 transfer case reset. The adaptation values will need to be reset with a laptop running BMW ISTA, or by bringing it to a dealer/shop that can do this for you.
Read this DIY on our blog: blog.fcpeuro.com/how-to-repai...
Shop Parts Used In This Video Here:
www.fcpeuro.com/products/bmw-...
These Parts Will Fit The Following Vehicles:
BMW X3
2004 BMW X3
2006 BMW X3
2007 BMW X3
2008 BMW X3
2009 BMW X3
2010 BMW X3
BMW X5
2004 BMW X5 3.0i
2004 BMW X5 4.4i
2004 BMW X5 4.8is
2005 BMW X5
2006 BMW X5
2007 BMW X5
2008 BMW X5
2009 BMW X5
2010 BMW X5
2011 BMW X5 xDrive35d
2011 BMW X5 M
2012 BMW X5 M
2012 BMW X5 xDrive35d
2013 BMW X5 M
2013 BMW X5 xDrive35d
BMW X6
2008 BMW X6
2009 BMW X6
2010 BMW X6
2010 BMW X6 M
2010 BMW X6 xDrive35i
2010 BMW X6 xDrive50i
2011 BMW X6 ActiveHybrid
2011 BMW X6 M
2012 BMW X6 M
2013 BMW X6 M
2014 BMW X6 M
Index:
Intro 00:00
Drain the transfer case and expose the actuator 2:50
Remove the transfer case actuator assembly 6:04
Disassemble the transfer case actuator 7:35
Reassemble the actuator 11:30
Reinstall the transfer case actuator 18:00
Refill the transfer case with fluid 19:45
Refit the transmission crossmember 20:50
SUBSCRIBE: hubs.ly/H0cDnfN0
Get free parts from FCP Euro:
www.fcpeuro.com/page/lifetime...
Follow FCP Euro on:
/ fcpeuro
/ fcpeuro
/ fcpeuro
www.fcpeuro.com/

Пікірлер: 185

@carlos-kx4sn 3 жыл бұрын

You nailed this video with all the details man. Well done video

@peculiarliving9474 Жыл бұрын

I just want to say thanks for such a thorough and well produced DIY. Very helpful.

@fcpeuro Жыл бұрын

Glad it was helpful!

@JG-gf9ho Жыл бұрын

Couple of similar videos about Actuator replacement in KZfaq. This one is the best.

@cruzfernandez4554 2 жыл бұрын

Very appreciated and worthy time watching the video. Thank you

@waynesalekin6773 3 жыл бұрын

Amazing video. Great job. Thank you very much!

@jbrown8059 3 жыл бұрын

Man you are the best, my bmwx3 2008 having same issue but i have useless mechanics in New Zealand..you explain it better than bmw people

@fcpeuro 3 жыл бұрын

We'll let Mike know you enjoyed it!

@ssdtrain1 3 жыл бұрын

GREAT JOB BRO !!!! AWESOME INSTRUCTIONS

@bobmathew3380 3 жыл бұрын

Great explanations and video!!!!

@nicholasnagy2848 11 ай бұрын

Outstanding instructional. I would give this video 100 thumbs up if I could.

@qollinsqollo2293 3 жыл бұрын

very very well elaborated and explained , thank you

@fcpeuro 3 жыл бұрын

You're welcome, Qollins!

@studiosupremechannel3517 4 жыл бұрын

Excellent baby!!!! Thank you for the video :)

@fcpeuro 4 жыл бұрын

You're welcome Studio Supreme. We got you bb 👶.

@martymeyer4125 3 жыл бұрын

Well done!

@2limecrew159 3 жыл бұрын

I just did this and saved a buttload of duckets baby! Gracias yo!

@anthonythurman3043 3 жыл бұрын

About to do this on my daughters x5..thanks for the thorough..lesson

@fcpeuro 3 жыл бұрын

You're welcome, Anthony!

@anthonythurman3043 3 жыл бұрын

Was able to do it..week before last..easy peasy

@ronaldslager1714 2 жыл бұрын

@@anthonythurman3043 any chance you are in NJ ???

@fazeleino8078 2 жыл бұрын

Thanks for this video thanks again

@xiayu27 3 жыл бұрын

18:52 you missed a baby for the baby counter! Excellent video. Thanks so much for sharing your expertise! Do you absolutely have to remove the 18mm cross member bolt to remove the actuator motor? EDIT: Finished the job already and the answer to my question is NO. Just have to lower the transfer case after removing the 4 cross member bolts to get access to the actuator screws.

@jorgerea939 2 ай бұрын

Awesome video, I have an X5, I appreciate it

@purplethumb5585 2 жыл бұрын

Great help thank you very much for sharing

@fcpeuro 2 жыл бұрын

Happy to be of help!

@Gerlingsbulldogges 25 күн бұрын

Found new favorite channel 🎉❤🎉

@fcpeuro 8 күн бұрын

💙

@adlaihampton1321 2 жыл бұрын

Great video, video will help me wit mine very good instrctor

@arnaudekko 11 ай бұрын

Hello, c'est la meilleure vidéo sur ce sujet, merci de France 🇲🇫, tres beau tee-shirt également 👍

@MrBliviu607 Жыл бұрын

Thank you ! 😊👍🏼

@2k20jordyn_pr6 3 жыл бұрын

Saved my life!!

@fcpeuro 3 жыл бұрын

glad it was helpful!

@bluechipautowerks 3 жыл бұрын

Easy, baby! Great video.

@fcpeuro 2 жыл бұрын

Boom baby!

@chrisp.5272 2 жыл бұрын

I definitely need to replace my fluid, 40,000+ miles. I also need an ECU repair, it’s temperature sensitive and starting it 2-3 times in the winter really sucks.

@mra4107 3 жыл бұрын

What are your thoughts about using the URO brand brass gear instead of the plastic one again? Greater longevity?

@vaem3872 3 жыл бұрын

Gracias, me ayudo mucho

@quong1 3 ай бұрын

hi mike love your work and appreciate all your expert advice and demonstrations. i have a serious question...i had my auto mechanic change the auto transmission filter change and gasket... he filled cold and did not check fill at correct temperature 2 weeks ago...and now at idle the automatic transmission is about to blow up and make horrible loud sound.... but once i get going i dont have any gear change issues.. but it sounds like a grating sound 2006 bmw x3 and now i dont know what to do...thanks mike

@erfanpalatin 3 жыл бұрын

Hi FCP EU, thank you for the in depth video, this helped my a lot. Just a question out of curiousity, i see people sell metallic version of the actuator gear , would that be a good idea to put on your car ?

@blackterminal 2 жыл бұрын

@@SuncoastCreate they should make a solid steel one

@creativemt4065 10 ай бұрын

Hi! Great Video. Hey, Do you know where the fuse is located? I change a brand-new transfer case (actuator motor) and still I have the lights coming up on my dashboard. Thank you!

@921aa Жыл бұрын

What stops the plastic gear from coming out while the worm gear is still in place? It would seem the only reason to take the motor out is to make it easier to clean the worm gear. Perhaps dremel tool with a small grinder would be better than breaking the casting.

@caseyjones7638 3 жыл бұрын

currently have an x5 e70 with these 4 lights on the dash with a d36a f~can message vehicles done 89000 miles could this be the cause thanks and great video

@jeanibiuna 3 жыл бұрын

Is it necessary to reset the service interval after a tranfer case fluid change? On this e83?

@luisg2665 3 жыл бұрын

What's the oil i should be buying? How bad it is if i don't reset it with a computer after?

@olymes808 2 жыл бұрын

Did I just hear you say you can replace the part for 500 bucks 🤯 I found the same part for 90 bucks… but great video.

@rockbottom7044 Жыл бұрын

What do you think of Valvoline transfercase fluid?

@Resq28 2 жыл бұрын

Great great video. Thank you. Ordering the new parts now. Can the vehicle be driven to the shop or will it have to be towed for the reset? Thank you.

@fcpeuro 2 жыл бұрын

That will all depend on how far gone your plastic gear is. If you have a loud clicking coming from it, we would suggest getting the vehicle towed. This X3 had just started to fail (audibly) so it was still in ok shape to drive into the shop for filming.

@Resq28 2 жыл бұрын

@@fcpeuro excellent. Thank you.

@fernandoquiros6387 Жыл бұрын

Amazing video, excellent teaching, thanks, just I want to ask a question. What are the failure symptoms when the Transfer Case Actuator is failing? In my BMW X5, 2008, there is a noise in the gear or transfer box and sometimes it just goes very slowly, without force or it turns off.

@sscummings Жыл бұрын

he just told you smh

@michaelbrown2112 3 жыл бұрын

Fantastic video! Those front Connecticut plates irritate the heck out me tho 😆

@gfdaemonio 4 ай бұрын

Do the new gear spin freely? Mine does now. It feels tight. The worm gear might strip it.

@JayBHooks 3 жыл бұрын

Thanks for the video! I notice that all of the DIY transfer case actuator repair videos and forums I've seen only apply to X3 models up to 2010. I have a 2011 and the transfer case is causing me problems. Will I find the same parts in the actuator? Gears etc? Did BMW change the transfer case design from 2011 on?

@mr2_mike 3 жыл бұрын

Typically just: 2004-2007 BMW X5 E53 2004-2010 BMW X3 E83

@arjaye8783 Жыл бұрын

Jay Hooks did you find any informational videos on 2011 X3 models? I'm curious to know.

@deangiorgi9889 Жыл бұрын

I have a question. How do you know which way to put the sensor in? I put it in what I thought was right but I still have the dash lights on for AWD and abs brake. Any help would be much appreciated.

@Alexjimb0 3 жыл бұрын

Lmfao the "sike" I almost thought u were me lmfao I talk to bolts all the time

@fcpeuro 3 жыл бұрын

Sometimes they listen... sometimes they dont.

@zdenekmasek7671 10 ай бұрын

You dont need to reset oil adaption after?

@cesarc.salazar4631 2 жыл бұрын

Does it also work the same for a 2011 BMW X3 F25

@Strickdaddy59 3 жыл бұрын

Thanks for the video. I am really struggling to get the 18mm through bolt out of the cross member. The exhaust piping is in the way and I cannot get anything in there. I've also tried an 18mm wrench and just cannot get enough leverage. Any tips?

@blackterminal 2 жыл бұрын

Someone else just skipped that and was ok

@Samuel-is4wl 8 ай бұрын

You really don’t need to take it out.

@motorpsychohead 2 жыл бұрын

I bought the car a year ago and I changed the gear, new fluid and the car ran fine. Now a year later the abs, 4x4 and tpms lights are on. ABS would apply every time I brake and the car hesitates like it's gonna stall then seconds after the tpms light comes on, that's when DSC system is disable ! The car runs fine after but without DSC and ABS, 4x4 and tpms lights come on. I changed to new 4 abs sensors but no fix. I have to take the abs fuse out to stop the abs to act up. Now I am just driving with bunch of lights on the dash, no abs and don't know if 4x4 still work or not! I also changed to the new actuator !

@2004skylinegtrr34 3 жыл бұрын

I did mine, but my gear was actually good. Still the light comes on for it. But i have an 2008 X5 4.8i

@donnye454 3 жыл бұрын

I don’t see 2013 X5 XDrive 35i on the list. Different than other 2013 X5s?

@allstar98134 Жыл бұрын

First off; thank you so much for the information; I was able to but the new gear for $11 on Amazon; spent an hour removing and replacing it with little difficulty; Here is what’s odd though; at first the warning lights were off, but came back on the next day; I pulled it out again; I believe that I did everything right; but I suspect that the actuator motor is having trouble turning the gear in the transfer case. Because after driving twice, the new gear is already damaged. Any suggestions on what to do next? Thank you for any suggestions.

@fcpeuro Жыл бұрын

Hi All-Star, it sounds like you may have an issue with the motor or the case itself. More diagnosis will be needed in order to determine the issue. You may want to consider resetting the adaptations if youhaven'tt already.

@e24kgold Жыл бұрын

@@fcpeuro How do you reset adaptations?

@ve2430 Жыл бұрын

Does this apply to the e46 xi models?

@rockbottom1014 Жыл бұрын

I just replaced the actuator and all three lights are still on. Should they eventually shut off in their own?

@othmanelahrach1247 2 жыл бұрын

Hi, i did open it and that plastic part was like new. I replaced it since i already opened everything just in case. I believe the fault maybe from the electric motor. How can i test it with 12 battery vault, there is 7 pin.

@DAMCARTER1 2 жыл бұрын

I bought a 2007 BMW X5 E70. I have it for 1 year 2 months. I recently noticed there isn’t a front drive shaft . I want to install one but I saw a few videos where people were having issues with the length. Can I use a later model drive shaft? Which one will you recommend?

@fcpeuro 2 жыл бұрын

Hi Daaka, we would recommend finding an original replacement part. Using your VIN you should be able to source the correct part number for it.

@manuchargaprindashvili8036 Жыл бұрын

transfer case gut

@weerawat4864 3 жыл бұрын

Does this work with 2011 X5 3.0d?

@simplelangperorock 3 жыл бұрын

9:48 lmao. that got me.

@fcpeuro 3 жыл бұрын

whooooopsy

@guillermomulgrave7330 2 жыл бұрын

Question(My 2007 x3): My transfer case was changed to a used one and it removed the ABS/Brake/4x4 lights from being on. Now I hear a scratching sound from the back that was NEVER present before. Do you have a professional opinion what could be happening or what could be checked?

@fcpeuro 2 жыл бұрын

Hi Guillermo, the best thing to do is start with the easiest, which would be to check the heat shields. There is a good chance one was bent out of the way and is touching something while driving. Otherwise, a more deep inspection will be needed to ensure everything was secured properly, fluids were topped off, and of course that the replacement case is healthy. Crossing our fingers it is just a shield!

@manuchargaprindashvili8036 Жыл бұрын

bmwx3 e83 2008. 3.0 si. I have the same problem. When I turn the steering wheel to the right, brake da 4/4 lights up. Do you know what's wrong? Diagnostics does not write to the angle sensor.

@Samuel-is4wl 8 ай бұрын

I just did this but my I’m having issues with my rear tires. Is there something else I need to do?

@patrioty3k Жыл бұрын

Will this work for 2010 X5?

@Illogic10 4 ай бұрын

@fcpeuro Does it matter if you use the old sensor? I’ve heard if it’s in good shape use the old sensor?

@fcpeuro 4 ай бұрын

If you had no issues with any of your sensors prior to the repair, you can continue to use them.

@MoCityT3xAZBaby 2 жыл бұрын

Do u have to reprogram it after installing?

@gemmavanrooyen1668 2 жыл бұрын

I would also like to know this. Replaced by car now shifting loudly and shuddering on breaking. When I turn of XD shifting is fine, but obviously power is low and it's not a solution. Getting a code re calibration of the TC. Do we need certain software to reset?

@rockbottom7044 Жыл бұрын

How do you know you have a bad actuator?

@quartznation9499 3 жыл бұрын

I was hearing the actuator clicking after turning off the car.. Before I had chance to replace the gear my x3 went into limp mode.. So I replaced the gear but now what do I do about resetting the limp mode? Or will it reset itself? Or should i push to mechanic? Please help thanks Cleared all codes generic code reader.. Cleaned 4 speed sensors..spark plugs. camshaft/crankshaft sensors, maf and checked all fluids.. Disconnected battery for 3 days.. I'm scared to turn ignition and see the Christmas lights.. It's not even thanksgiving yet

@fcpeuro 3 жыл бұрын

You may need a more powerful scanner to clear all the codes (transmission).

@quartznation9499 3 жыл бұрын

While waiting for the actuator to arrive, I took the battery out of the car and kept it on a trickle charger so after 3 days and I replaced the actuator reattached the battery and the limp mode went away yay

@gdivision951 3 жыл бұрын

@@fcpeuro great content and instruction video ! 👌 Question, regarding that adapation, is it just resetting all fault codes from car's ECU or it sth else, would you be able to explain that to me ? Thx 😁

@bethells86 Ай бұрын

Lacking any good closeups

@scott2495 2 жыл бұрын

Wow it amazes me some of the noob questions that get asked in the comments section when he literally goes through EVERYTHING to do the job at hand

@theagam97 3 жыл бұрын

This also works for E90 325xi (drive), right?

@fcpeuro 3 жыл бұрын

Similar process, yes!

@fernandoruano1000 3 ай бұрын

Can you help? I changed the whole transfer case gear in my car, but the lights are still turning on.

@maximrabah2169 9 ай бұрын

PLEASE HELP OR ADVISE : I have problem with my e46 325i /2001 1-Battery light is on 2-transmission faulty light is on 3- I hear a bang when switching from reverse to drive 4-instrument cluster does mot show which gear the car is on P,R N Or D When I start the car and see this sign faulty transmission , the car can drive on reverse and other gears except for first gear. If I start the car and sign does not show on dashboard, the car only drives on first gear 35 Km speed max. Took it to many mechanics and nobody could fix it. First guy said he fixed alternator and reprogrammed ECM , The second told me to check and change Positon switch which I did today and still problem not fixed .Now they are saying its the alternator which the first guy fixed. I checked the battery its giving 12.4 V and when car started and I hit Benzin pedal it goes up to 13.9-14 Volt .

@JMlivePR 2 жыл бұрын

I take out the transfer case but the gear are good. What's the another possible issue ?

@fcpeuro 2 жыл бұрын

Hi J&M, it will all depend on what exactly you are experiencing. If you have already performed this service, we would advise checking the rest of the driveline for any possible failures. Starting with a fluid service on all the components first and going from there!

@johnvargas997 2 жыл бұрын

I have an 2011 bmw x5 N55. Is it same procedure for my vehicle? Thank you in advance.

@fcpeuro 2 жыл бұрын

Hi John, while the idea _may_ be the same, your model specifically uses a different actuator motor than the X3 in this video.

@glenglene8473 Жыл бұрын

what symptom if the plastic gear worn out? does the vehicle hesitate when accelerating?

@fcpeuro Жыл бұрын

Hi Glen, you will often see error lights on the dash, have a code stored in the ECU, and in some cases will hear a clicking coming from the transfer case.

@Kapu5-15 2 жыл бұрын

Are you guys are located in CT

@fcpeuro 2 жыл бұрын

Hi Ariel, we are located in Milford CT!

@fasbird1000 3 жыл бұрын

Can u give a specification about the kit plastic if I need to buying from the dealer?

@fcpeuro 3 жыл бұрын

What information were you looking in to?

@fasbird1000 3 жыл бұрын

thnx already done (transfer servo acutator ..motor gear box kit plastic replacement) thanx

@5818lopser 2 жыл бұрын

Are transfer cases compatibles from 2006 to 2007 on x3?

@fcpeuro 2 жыл бұрын

E83 units should be interchangeable from their 6 year run😎

@waynesalekin6773 3 жыл бұрын

Will an OBD reader for a BMW clear the codes and reset the adaptation values?

@mcplutt 2 жыл бұрын

The icarsoft BMM 2.0 or 3.0 will probably do just that.

@bradleymoyer5236 2 жыл бұрын

Wait wait wait why didn’t you reset the values? Doesn’t it do major damage if you don’t ?

@fcpeuro 2 жыл бұрын

Hi Bradley, good question! As Mike mentioned in this video, the vehicle just started showing signs, so it continued to drive fine after the repair. On a highly affected vehicle, it would certainly be critical to reset the values. If you have the tools to do so, you can also do it, needing it or not.

@angelmedina541 Жыл бұрын

I'm sorry, I replaced the actuator but the 4x4 warning light on the dashboard is still on and the 4x4 doesn't work, what could be the problem?

@fcpeuro Жыл бұрын

Hi Angel, you will want to scan the vehicle for codes and diagnose further. It is possible your vehicle has a deeper issue than just the actuator gear!

@ronaldslager1714 2 жыл бұрын

Hey.. I have a BMW X5 2006 3.0 . Mechanics did a scan and still are clueless! Codes say 227 & 228 ( o2 bank 2 control deviation and o2 bank 1 control deviation.. ) Also I have 4x4 DSC Inactive light on suddenly! and I hear grinding noise underneath at hard stops like down a hill...(NO Abs lights on) I assume Transfer Case Motor or Gear ??? Or oil ???...It feels like brake locks on when I stop down a hill.. What could it be??? Also... My check engine light has Always been on for 3 years ( Map Thermostat code) but every mechanic told me not to bother replacing that part... Recently The car has trouble starting every morning and when low on fuel. !! Cranks but No start for at least 5 cranks... *Maybe Fuel pump Relay?? *Fuel pressure regulator?? *Fuel filter?? *Fuel Injectors ?? They cant figure it out!!! Seems the Fuel Pump is working.. I Went to over 20 car shops in 3 weeks and am really frustrated :( What could it be ??? They cant figure it out !!!

@blackterminal 2 жыл бұрын

Fuel filter then pump in that order . Try that

@samuelthomas9637 8 ай бұрын

I just did this. After about a week my wheels are locking up. Does anyone know what the issue is?

@calvinhenshaw2147 2 жыл бұрын

what was the name of the software that was needed on the laptop ???

@fcpeuro 2 жыл бұрын

Hi Calvin, that would be BMW ISTA software.

@josealfredovalles435 3 жыл бұрын

We’re do you fine the parts for vmw 2005

@fcpeuro 3 жыл бұрын

To find the oarts for your vehicle, you'll want to enter your year make and model intot he site!

@TheMartin139 2 жыл бұрын

Hi, does anyone know what size are the copper washers for the tranfer case

@1057811 2 жыл бұрын

18 X 22 X 1.5 mm I hope this message isn’t too late

@TheMartin139 2 жыл бұрын

@@1057811 thank you!

@bartbixler3278 2 жыл бұрын

Look at those Chops..

@jaro324 3 жыл бұрын

Trzeba jeszcze zrobić adaptacje po OBD.

@gdivision951 3 жыл бұрын

Jaro, w jaki sposób ją przeprowadzić ? Mam OBD Carly II gen. Będę wdzięczny za info :)

@jaro324 3 жыл бұрын

@@gdivision951 nie pomogę bo robił mi to warsztat

@gdivision951 3 жыл бұрын

@@jaro324 rozumiem- pozdr

@jaro324 3 жыл бұрын

@@gdivision951 Również ✌️

@SunilKumar-mm8bx Жыл бұрын

My problem 55c3 error code

@saistylezwigartistry1616 2 жыл бұрын

Is it possible to do this at home without a car lift? Or do you need it that high

@fcpeuro 2 жыл бұрын

You can certainly do this job at home, the main thing is to have the vehicle level for proper filling of the transfer case fluid!

@saistylezwigartistry1616 2 жыл бұрын

@@fcpeuro my transfer case was just flushed and gasket replaced 6 months ago. Can I just replace my actuator

@surreaLinnovatioN Жыл бұрын

Watching @9:51, mentally moves on to buying the part and skips to @18:00

@moonsapling Жыл бұрын

Is this a permanent fix?

@fcpeuro Жыл бұрын

This fix will be good for another 100k or so, however the fluid should be changed way before that!

@rogereprest Жыл бұрын

I just figured out that that Micheal is really the lead singer from the Baby's

@fcpeuro Жыл бұрын

😂😂😂😂

@9PieceStraight8Balls 3 жыл бұрын

Can I just buy the whole Bosch actuator shift motor from eBay for $90 and replace it instead of going through these steps?

@Sulser007 2 жыл бұрын

I also just bought a new actuator for $100 Instead of opening it up I will just change it... Now the $100 Question... Is this one going to last???

@delta3eight 2 жыл бұрын

100 dollars for that gear? I’ve seen them for barely 15 dollars

@simplelangperorock 3 жыл бұрын

it must be nicer if you have a camera from above your head. thx

@coolraul71 3 жыл бұрын

How the hell is this well designed if its made of Plastic?!?

@bengazetti4143 3 жыл бұрын

what are the signs when Actuator goes bad ?

@2004skylinegtrr34 3 жыл бұрын

You get the 4x4 and brake light on the dashboard

@Sulser007 2 жыл бұрын

XMAS Tree lights up in the Dash... lol

@user-fu7qt8oz6r 4 жыл бұрын

Почему она ржавая???

@tubbycustard8866 3 жыл бұрын

this is a nightmare if you only have floor jacks my neck hurts

@fcpeuro 3 жыл бұрын

Gotta use a neck brace next time Tubby Custard! Did you get it done?

@tubbycustard8866 3 жыл бұрын

@@fcpeuro got it done couple weeks ago! unfortunately my 4x4 and brake light comes on the dashboard still... back to the drawing board

@blackterminal 2 жыл бұрын

@@tubbycustard8866 light on before or after fix?

@tubbycustard8866 2 жыл бұрын

@@blackterminal after the fix, however that BMW ended up totaled after a deer decided to run in front of it lmao

@blackterminal 2 жыл бұрын

@@tubbycustard8866 oh no. Sorry to hear that

@blackterminal 2 жыл бұрын

Can you get a metal gear?

@fcpeuro 2 жыл бұрын

There are some outside aftermarket options for a metal gear replacement.

@mcplutt 2 жыл бұрын

yes, a brass gear

@blackterminal 2 жыл бұрын

I think the dealer would give you grief for doing the fluid yourself. What if you just don’t reset the computer?

@fcpeuro 2 жыл бұрын

If you are doing the fluid at a normal service interval, with no issues or codes then you can typically just change the fluid and go. On this specific X3 we worked on, there was a code for issues with the t-case, for which we had to reset adaptation values.