BMW 3 series E90 E91 2.0L N47D20C injector leak (copper seal) full repair video #BMW #N47 #injector www.gofundme.com/f/33s7b-yout...
Пікірлер: 97
@johnconnor5134 жыл бұрын
Excellent video. Almost therapeutic to watch. Thank you for sharing
@MustangMotors4 жыл бұрын
junaid hussein thank you
@alexandru15453 жыл бұрын
Outstanding and very Explicit video, WELL DONE GUYS, FALL DEEP INTO THE VIDEO,✌👏👍
@Xfacehack5 жыл бұрын
I guess this applies to all n57 and n47 engines? Did the car run fine before?
@erkanuyar70965 жыл бұрын
Perfeckt
@des27015 жыл бұрын
Did you use loctite on the injector bolts, or copper grease? Great video BTW. 👍
@MustangMotors5 жыл бұрын
Hi it’s a copper grease, thank you
@theeroom4 жыл бұрын
Dam messy, Excellent video! Thank you so much! , what error code did that throw up? How does the copper seal get damaged?? 🤔🤔
@MustangMotors4 жыл бұрын
theeroom hi didn’t checked the codes, due to engine pressure or if new copper are not replaced in service.
@melito21172 жыл бұрын
@@MustangMotors possible that this is the reason it goes into limp mode when hot?
@MustangMotors2 жыл бұрын
@@melito2117 have you checked your injectors? or this is a very common problem abs ring on the rear wheels kzfaq.info/get/bejne/rbx9ksygtLWpe30.html
@darrenhudson36784 жыл бұрын
Hey great video, I have the same car and noticed the nut your removing at 4.50 has a small bit of oil showing, would this be a bad injector or an O ring gone? thanks
@MustangMotors4 жыл бұрын
Darren Hudson hi it’s due to bad copper O ring and fuel leak from the injector leak off test at the start of the video.
@peterbentham4705 Жыл бұрын
Do you need to code them in as I need 4x injectors
@MyJarrus5 жыл бұрын
after changing the seal you do need to crank the car for a long time to release the air until it fires up
@MustangMotors5 жыл бұрын
Jarrus Killa yes you do, you may try prime fuel by ignition on/off
@aqifrajaa13634 жыл бұрын
Guys i have replaced my leaking injectors and the coper washer and put it all back together properly and its still leaking... i have cleaned the injector and the hole but still leaking any help guys ????
@racerboi934 жыл бұрын
What size thread is the connection for the removal tool? I've found a tool but it has to be m14
@MustangMotors4 жыл бұрын
Hayden Andrews hi as long as you can screw the injector puller into the injector will do the job, you are replacing it anyway! Should be m14
@waterfordMARTIN5 жыл бұрын
How did u clean all tha area..mine looks terrible dirty too. Same problem on first injector as in your video
@MustangMotors5 жыл бұрын
waterford Martin I used lots of brake cleaner and blow air is the way forward
@waterfordMARTIN5 жыл бұрын
@@MustangMotors ok thanks..will that be a problem if some of that rubish fall down to cylinder when cleaning? Or u put something in while injectors was out?
@MustangMotors5 жыл бұрын
You can put a price of cloth or tissue paper, if it falls into cylinder you can use vacuum cleaner to get it out :)
@Grimm666Jow2 жыл бұрын
Thank you sir for this video. Helped me very much. I just hope they dont break when i remove them in future. Did you use new screws for a clamp and did you use thread sealer ?
@MustangMotors2 жыл бұрын
Hi hope it was successful no used same clamp and new seal
@Giancarlo-ol2mu Жыл бұрын
This engine is all wet in oil. The video shows that the injectors have worn copper seals. Hopefully, before reassembling everything, the injectors have been cleaned with ultrasound but above all a calibration for each individual injector.
@jackbarnes23022 жыл бұрын
Hi what did you use to clean the injector seat? Also did you put anything on the injector before refitting it? Thanks
@MustangMotors2 жыл бұрын
Hi just you can use tool like this www.amazon.co.uk/Injection-Nozzle-Injector-Manhole-Cleaning/dp/B0989Y7Q54/ref=asc_df_B0989Y7Q54/?tag=googshopuk-21&linkCode=df0&hvadid=534924970221&hvpos=&hvnetw=g&hvrand=471513948192361880&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9073540&hvtargid=pla-1442065331001&psc=1 I changed the injector copper seal before refitting.
@jackbarnes23022 жыл бұрын
Thanks 👍
@serhiobc4 жыл бұрын
Can you please include the type of Injector puller you used in the description. What is the part number of the Injector?
@MustangMotors4 жыл бұрын
dreamchaser I used something like this www.amazon.co.uk/DiLiBee-Injector-Extractor-Injection-Injectors/dp/B07WNVD45Y
@tobyexe12843 жыл бұрын
Hi what is the the part number for the blots please or the specs i cant seem to find them great video by the way
@MustangMotors3 жыл бұрын
Hi please try this website www.realoem.com/bmw/enUS/select If you need help I can help look it up for you
@kapna40484 жыл бұрын
Hi, how did you clean injectors area?
@MustangMotors4 жыл бұрын
Kapna4 I cleaned with brake cleaner www.amazon.co.uk/Polygard-12200-Brake-Clutch-Cleaner/dp/B004WODOEE
@denischis82013 жыл бұрын
Hi mate, I have a bmw 320d 2011, if the car starts it starts quite hard and after it starts well, I have the engine on, it takes out cases that drown you, the car pulls very well, what problem can it have?
@MustangMotors3 жыл бұрын
Hi possibly a glow plug or module. Try to Get scanned for trouble codes.
@oCaptainKorma4 жыл бұрын
Hi my car has this issue, I get oil around the injectors on the head, I soaked and removed all oil after driving to work and back pools of oil have returned
@MustangMotors4 жыл бұрын
Ronak Vaghela you should clean and start the engine and investigate the oil leak or is it fuel leak? Then fix your concern
@Wiseman-ej1bd22 күн бұрын
Ten silnik srał olejem na te wtryskiwacze?
@nightstalker19943 жыл бұрын
My 118d is doing the same thing, is it also common to have whitish smoke coming from the same area?
@MustangMotors3 жыл бұрын
Hi it seem too, your fuel injector copper seal needs replacement soon.
@nightstalker19943 жыл бұрын
@@MustangMotors thank you, also great video, very informative.
@yuriromanov40965 жыл бұрын
Hi. How did u remove old seals. Thanks for video
@MustangMotors5 жыл бұрын
Jurij Romanov 10:46 -11:46 :) thank you
@yuriromanov40965 жыл бұрын
A removed injectors without seals. old seals is stuck inside how can remove them. Thank you
@MustangMotors5 жыл бұрын
Normally you can use a long thin metal (pick tool) to pry or move the copper seal. Or try using small amount of lubricant.
@yuriromanov40965 жыл бұрын
Thank you
@winnerwinner34163 жыл бұрын
I have diesel leak front injector 1, is the problem the injector itself or is it the injector ring? Thanks in advance for replying.
@MustangMotors3 жыл бұрын
hi its the injector copper seal
@winnerwinner34163 жыл бұрын
@@MustangMotors thank you
@GeorgeAusters4 жыл бұрын
Why would you only replace 2 seals?
@MustangMotors4 жыл бұрын
George Austers hi the other injectors are ok
@scottcorke79444 жыл бұрын
If you replace the injector does it require coding?
@MustangMotors4 жыл бұрын
scott corke hi yes you do.
@PaulAntonescu4 жыл бұрын
So you torqued 8Nm and afterwards 26Nm?
@MustangMotors4 жыл бұрын
Paul ANTONESCU yes that’s right for injector clamps
@PaulAntonescu4 жыл бұрын
@@MustangMotors thanks
@theprodistini25904 жыл бұрын
hello, i was hoping you could help me out. I have a 2015 328d and last night it threw a code saying "Injector #1 At Max learning" Code P02CD Car runs and drives fine, doesnt hesitate or anything, Gas mileage is the same. and theres no fuel leaking or abnormal noises coming from engine or injector rail. Im wondering what you think i should do
@MustangMotors4 жыл бұрын
javier chavers hi there, you should clear the fault code and test drive and check if the fault code appears back! www.obd-codes.com/p02cd
@theprodistini25904 жыл бұрын
Mustang Motors I did that last night and it came back within 20 minutes :(
@theprodistini25904 жыл бұрын
On way to get two cans of seafoam to add to the quarter tank I have. Gonna run it close to empty and see if it clears up from the seafoam
@MustangMotors4 жыл бұрын
javier chavers good luck, if it does work, the next thing to check is the leak off test on fuel injectors
@theprodistini25904 жыл бұрын
Mustang Motors when doing a leak off test, is a perfect result 0 fuel leak? Or should there always be a steady small stream of diesel that comes out of each? I saw your video and noticed two didn’t seem to leak any. But the others did.
@RomoRacing4184 жыл бұрын
When this happens does the car run into limpmode?
@MustangMotors4 жыл бұрын
xXshitloadsXx maybe depends upon how seriously the injector copper seal is damaged
@mohammedshoibkhan4 жыл бұрын
Where did you order the seals from.
@MustangMotors4 жыл бұрын
Shoib Khan I got it from BMW
@QuattroBajeena3 жыл бұрын
Im gad mine never looked like that. Had a small leak on 1.
@nedas44173 жыл бұрын
Did it affect engine work?
@QuattroBajeena3 жыл бұрын
@@nedas4417 just a knocking sound and small oil leak, the engine bay cover the foam was soaked in oil, had a bad smell when heaters was on. New pollen filter. New O ring on the injector, Engine cover was removed till i sorted out the soot stain. After that car was fine. 2015 - present day.
@rusiskas4 жыл бұрын
Can you do this for my bmw and how much it could cost?
@MustangMotors4 жыл бұрын
Darius Vilčinskas hi where are you from?
@rusiskas4 жыл бұрын
Mustang Motors UK Spalding Lincolnshire. You mate?
@MustangMotors4 жыл бұрын
Darius Vilčinskas Folkestone Kent
@ashy10422 жыл бұрын
@54V44 жыл бұрын
I have Diesel leaking (at injector #1) at the back of the engine and also gas leaking. I've replaced the seal and cleaned everything up nice and tidy and after a bit over a day (40 miles driven aprox.) the problem is back as it was. I don't know what else I can do. Here is a link to a video showing the problem. kzfaq.info/get/bejne/p92Ih8uqvta-dI0.html Slacky power, fumes in the cabin, very bad fuel milage, These are the symptoms. At times I get the P0402 code (EGR related) but that wasn't the case when it was working fine + I had the inlet manifold, throttle body and egr cleaned recently with swirl flaps delete. Any suggestions, please? Thank you!!!
@MustangMotors4 жыл бұрын
hi I have seen your video, the injector 1 is the front of engine. Anyway the best thing to do is remove the panel above the engine for the cabin filter and see the injector clamps are tight to specification and the injector return pipe are secured. Clean and start the engine to check is the way forward for the fuel leaks.
@54V44 жыл бұрын
@@MustangMotors Kind thanks for your comment. I did use the correct specifications when putting things back together (torque wrench, etc), and ended up replacing once more the return pipe (tube) that was leaking (again). I cleaned up the diesel and seems fine now. I can smell diesel in the cabin but I'm assuming that will eventually evaporate at some point. Will check back after tomorrow's commute. Thx again and stay legendary! :)
@adrianogambuto23294 жыл бұрын
Rumore delle punterie, sono rovinati i martelletti, causa olio errato
@MustangMotors4 жыл бұрын
Adriano Gambuto yes that’s correct Tappet noises, hammers are damaged, due to incorrect oil
@NHEFF093 жыл бұрын
mine makes that ticking noise
@MustangMotors3 жыл бұрын
I guess you have checked under the engine cover! If it’s not injector leaking. Does the ticking noise changes on higher or lower engine revs
@NHEFF093 жыл бұрын
@@MustangMotors it did leak from the the little rubber hose the thing that clips onto the injector under the cover and foam sound proofing, but fixed that. it knocks when cold and under load at about 1500 revs to about 2500revs.
@MustangMotors3 жыл бұрын
@@NHEFF09 hi does the knocking sound come from the bottom of the engine?
@NHEFF093 жыл бұрын
@@MustangMotors no im sure its from the top.im thinking its injector
@NHEFF093 жыл бұрын
@@MustangMotors hi just to confirm i replaced injector number 4 knocking has gone for the moment. will test it tomorrow again as it will be a cold morning.
@HardCoreMore4 ай бұрын
Why did you show us engine start from the cabin??? 🤦♂ That was so anticlimatic