BMW E30 Rear Subframe Assembly RESTORATION | BMW E30 325i Sport Restoration E4 S1

Рет қаралды 1,469,648

5 жыл бұрын

In episode 4 of the BMW E30 325i Sport restoration, I restore the rear subframe along with a few things attached to it.
This one really put me to the test. Not only the project in hand but filming it also. Apologises for the dark shots every now and again. It started with battling the old rusty parts off. Lots of tapping and prying was involved. And once it was all off, it was still a nightmare to get apart. I had to get help from friends on several occasions during the process.
Once everything was apart and degreased, I set about pushing the bearing and bushes out. This was stressful, even with a press. Once out, I blasted all of the pieces I was going to restore even the nuts and bolts. The subframe itself and the control arms were given to a friend to take to work and blast using professional blasters. Made my life a lot easier considering I couldn't fit the subframe into my homemade cabinet.
Once everything was free from rust and paint I polished the nuts, bolts and other small pieces and started the long process of zinc electroplating them. This would take me around three days in total, on, off plating when I had time. Whilst I was waiting for things to plate and dry, I realized I had forgotten about the sway bar and quickly de-rusted it with the Onyx 320. I then masked everything ready for paint.
Firstly a coat of etching was added, then high-build primer. That was then sanded back with 500/600 grit sanding pads and Quarts Deep Black (The deepest black I know of) was added. Finally, Quartz lacquer to seal everything in, and make them shine. Once eve had dried it was time to carefully press in the new bushes and bearings. This was achieved by doing the opposite of the removal.
Everything was then put back where it came from restored or new and the restoration was complete. As I said in the video with the car being just a shell, no differential in and fresh springs, shocks, bushings, drop links etc... It will take some time for everything to settle down to the correct ride height.
Thanks for watching and be sure to subscribe with the bell on to be notified of the next episode!
If you would like to send me something to restore, tools to use or anything to support Restore It, please send to:
Restore It Mail Box
PO Box 50
CHATTERIS
PE16 9AZ
Subscribe for Weekly content!
Tools & equpitment used:
Quartz Lacquer - goo.gl/8PTVKM
Base Coat Paint - goo.gl/mWhufG
Rust Remover - goo.gl/13gopW
Moldex Full Face Mask - goo.gl/NNYGrv
FGL 5 Spray gun - goo.gl/Acg5rd
A.N.I. R150-T Mini Spray gun - goo.gl/cHTJS2
Colad Washable Overalls - goo.gl/3Css9E
Colad Mixing Cups - goo.gl/8DYmE8
Colad TurboMix Sticks - goo.gl/cYZfks
Colad Synthetic Paint Strainers - goo.gl/H79ZgL
Steel wire bits - geni.us/keyaD
Rotary Tool - geni.us/HGed
Concentrate Degreaser - geni.us/yUn9
Mannesmann Socket Set - geni.us/HCDZ
Thanks for watching!
- Disclaimer: I am no professional. I am completely self-taught and would appreciate any feedback, advice or constructive criticism.
I don't add music to these videos so that you can choose to listen to what you like if you would like to.
#BMW #E30 #Restoration
Become a patron to win the Items featured in these videos!
Patreon - / restoreit
PayPal Donations - restoreitchannel@gmail.com - If you would like to help towards more tools and projects.
Follow me on Social media to keep up to date with videos and giveaways.
Twitter - / restore__it
Facebook- / restoreitchannel
Instagram - @RestoreItChannel
Patreon - / restoreit
Discord - I now also have a discord server if you want to chill with like-minded people and maybe learn something new. - / discord

Пікірлер: 838

@RestoreIt 5 жыл бұрын

Finally, this one is finished. This was a really big undertaking for me as I've never done this before. I got there in the end, with a little help from my friends and smudge the boss. It was a bit rushed towards the end as you can kind of tell... *Not a lot left of those* and any other mistakes I've made :D It's been a long two weeks. I'll be taking a short break from the E30 to get some other items restored. Stay tuned for next weeks video!

@type2523 5 жыл бұрын

Restore It I love the BMW related videos !

@type2523 5 жыл бұрын

Restore It I love the BMW related videos !

@type2523 5 жыл бұрын

Restore It love the BMW videos !

@nazarp6011 5 жыл бұрын

Not the biggest BMW fan, but love your restoration videos of that car! I am very interested in the older car restorations. Maybe when you finish with BMW you can do other cars (American or Japanese).

@pekkasaarinen2902 5 жыл бұрын

The boss seemed quite typical: 'I'm just grooming myself, while you do all the work' type. 😁

@colinaskey9777 5 жыл бұрын

Doing a job like that under those circumstances is without doubt extremely difficult,it's hard enough with a car lift,but on your back on the floor makes 10 times harder,you're to be commended,the job was first rate,well worthy of my 5 ☆ rating

@mickea769 5 жыл бұрын

Just love the sound of fast hammering

@masallahsejtan3312 5 жыл бұрын

And painting 🙂

@garymucher9590 5 жыл бұрын

I do like the fact that you don't short cut the work. You media blasted everything and then used etching primer and then regular prime. And topped that off with base coat paint and clear coat. That will never give you a problem again. Thumbs Up!

@iraqafghanistanmarine6905 5 жыл бұрын

Dude, seriously, EYE PROTECTION!!! You can’t see you can’t work. I admire your tenacity and willingness to tackle big projects. I was the same way. The only way to learn is to just do it yourself. You will learn what works and what doesn’t. It is an exciting journey, especially when all the hard work pays off👍😉

@mrsafwan7223 5 жыл бұрын

From this channel I never miss a video

@sameerk3349 5 жыл бұрын

Best restoration channel

@Jake-ul5nl 5 жыл бұрын

100%

@grahamefreestone5309 5 жыл бұрын

I totally agree Sameer.. 👍

@mantaship 5 жыл бұрын

Why do I love these? I am not restoring a BMW, E30 or otherwise. But love them I do. Don't care about the length, I love the detail. Keep going...

@MRNVCDIY 5 жыл бұрын

Great job. Nice restoration

@fhunkiedude 5 жыл бұрын

Your video's help me relax so much! Thanks!!

@lukeperry1053 5 жыл бұрын

So satisfying when u lay out all the parts on the ground all organized

@shadowzedge5793 5 жыл бұрын

That was rather ingenious using the threaded rod, nut, and stack of washers to remove those bushings!! Greetings from the USA 🇺🇸

@irishwristwatch2487 5 жыл бұрын

I was just showing my grandad this series about 3 hours ago....decent timing there! That sanding activated primer looks mint too

@mgmg3561 5 жыл бұрын

Day and night, your dedication in little details. More then restoration, passion and self respect. Applause.

@pancakes427 5 жыл бұрын

I love your ingenious way of using plate steel and thread rod and washers to serve as a means to dislodge stuck items. Smart stuff.

@mohsenbeigi7068 5 жыл бұрын

It was really hard work and you have done in the perfect way, with accuracy and discipline. thank you.

@davesmith7671 5 жыл бұрын

Really enjoy watching the restoration process. I actually have a rear end to rebuild on my vw polo so this video has been really helpful in seeing what's going to be needed for me to undertake the same kind of thing you just have . Thanks for the hard work and videos

@asimkarimov6470 5 жыл бұрын

Restoration like 50% of creating something from beginning - very difficult work and a lot of money that you spending in general! So good luck men! And great thanks for your patience to taking video shoots and publishing them! Myself restoring german industrial sewing machines, I understand very well and big respect to your professionality! Greetings from Baku, Azerbaijan!

@CookRacingUK 5 жыл бұрын

Love these videos! Bring back some bad memories of the subframe... but good to see how the rear hubs aren't too hard. Great tips.

@MF-uf2qf 5 жыл бұрын

Forget yoga, this is the proper video to watch for relax (with a cup of coffee) :D

@Gilhus1985 5 жыл бұрын

Couldn't agree more :D

@WelcomeToTheMadness 5 жыл бұрын

That cat is clearly not afraid of anything. " Oh you're putting back up the sub-frame...yeah I'm not moving!"

@RestoreIt 5 жыл бұрын

She is so brave and care free. I kind of adopted her. She grew up in a loud house full of loud people.

@raytrace2432 5 жыл бұрын

This is absolutely normal behavior of cats, when they fell safe and and at home on some enviroment - to not afraid of anything and go and sit wherever their cat's soul desire. Shortly speaking, this cat is loved:-)

@sohailjaned 5 жыл бұрын

Good old fashion less talking & more action. This cars going to be sick when it's complete.

@nomoremrniceguy368 5 жыл бұрын

Forgot I'd subbed this, and when the notification came up I thought it was the lad in the US with the beemer who is equally skilled. This is art. The near silence with only ambient noise and tools etc is bliss and unfortunately too rare.

@billrice1381 4 жыл бұрын

Thank you for this. I am doing a rear axle restore on my 1987 E30 convertible and this was very helpful.

@DanteTheAbyssalBeing 5 жыл бұрын

There's nothing more pleasing than watching bearings/bushings being pushed in.

@chrise202 5 жыл бұрын

Awesome vid man. Thank you a lot for showing all the pieces in one go, that is really useful!

@grahamefreestone5309 5 жыл бұрын

Around the 14:10 mark you're using a treaded bar to remove the bushes. Slide on a ratchet spanner first. It's so much quicker. You're doing a fantastic job of everything. 👍🇬🇧

@SalandFindles 5 жыл бұрын

+Big Ben Bushings**

@grahamefreestone5309 5 жыл бұрын

@@SalandFindles ... Lol. I did type in bushings, but it looks like I'm a victim of corrective spelling. I suppose you could use the threaded bar to take bushes out as well... ;-)

@serenity6415 5 жыл бұрын

@@grahamefreestone5309 *snicker* Is that like "ribbed"? hehehe.. There are so many innuendos in tools and mechanics, and I've watched so many of these lately, that my dirty mind is on high alert now.

@grahamefreestone5309 5 жыл бұрын

@@serenity6415 .. Nothing wrong with a tool innuendo.. I'm sure there's more to come.. ;-)

@serenity6415 5 жыл бұрын

@@grahamefreestone5309 Baaahahaa.. I won't even type my response to that. I'll just behave myself and go watch him work with his 8" bench grinder.

@sheasrusticcorner1623 5 жыл бұрын

Man you just keep getting better and better!!! Thanks bro!!!!

@em1tuning797 5 жыл бұрын

Great video! I'm impressed by the quality of work performed on your rear subframe. Not many people willing to give that much time and attention when rebuilding or restoring their vehicles.

@clickireland1113 2 жыл бұрын

Tip: Great work, Thanks for the fantastic videos. Tip: Rather than 500 - 600 grit pads to prep parts after primer : I shoot sand in the cabinet at 30psi - and being light on the trigger. Being careful to not make spot delays or over-passes. Works out well. And if I have over-blasted looking afterwards in daylight (only job), I can re-prime that area, dry and prep it with grit pad. Very handy.

@AkAsCoTTii3 5 жыл бұрын

Awesome work and looks great. Can’t wait to see the finished thing

@vexedpixels 5 жыл бұрын

I'd love to see a full restomodding on the E30, cleaning it up and building it how you want!

@WelcomeToTheMadness 5 жыл бұрын

More E30 action

@nazarp6011 5 жыл бұрын

Agree. I think that the car would benefit a lot by upgrading few things. For example since he took the rear apart why not upgrade rear brakes to disk ones and maybe convert it to 5 lug nuts

@digitalrailroader 5 жыл бұрын

Nazar P. Actually the car already has rear disc brakes; what you saw being disassembled was the parking brake.

@playlistforkids 5 жыл бұрын

love this series....I did this for my E30 months ago and kinda burned out after finishing....this is a lot of work for one person. Congrats.

@RestoreIt 5 жыл бұрын

Thanks man and congrats on finishing yours.

@pgriggs2112 3 жыл бұрын

A craftsman sands the places no one sees. :)

@stevewilson6390 5 жыл бұрын

When it's completed and you are rich and famous dont ever even think of selling it . Keep it and pass it on to your future family as a legacy . They will be lucky enough to be able to see your hard work and endeavour.

@tj84vinnie 5 жыл бұрын

Work of art love it and can't wait to see more

@bothfeetin 5 жыл бұрын

8:00 those snap rings...what a pita! I tackled my rebuild last year. Great video!

@MachineInput 5 жыл бұрын

Great job again

@aitorbleda8267 5 жыл бұрын

What an ingenious way of extracting things without an extractor!!

@TDSG34 3 жыл бұрын

awesome! Love the attention to detail - satisfying to watch

@essamkhatri3978 5 жыл бұрын

Excellent restoration. Just loving your work. 👍🏼👍🏼👍🏼👍🏼👍🏼

@dzhipanutye 5 жыл бұрын

You as always is cool!!! Greetings from Russia)

@gabrielflegler8680 5 жыл бұрын

Love this series so much

@MrEyad1990 5 жыл бұрын

You did a 2 man job all by your self . It wasn't easy . I'm proud of you .

@michaeltchilds 5 жыл бұрын

You’re flipping awesome. Keep it up.

@playlistforkids 5 жыл бұрын

awesome work man, really enjoyed watching this one.

@slothgarage 5 жыл бұрын

Great video as usual! Half tempted to remove my subframe for a refurb now... decisions decisions... looking forward to your next video.

@intelinsideTV 5 жыл бұрын

Dude loving this series and all your videos! Keep it up!

@eccomanager1708 5 жыл бұрын

Whats with the dislikes? What is there to dislike? Guy isn't talking, so he can't say something wrong, he does his best to take apart part of the car he is restoring, and making it look as stock as it can be, and than puts it back together. So if you dont like the way he works, find other sites that does it better (if there is any other channel that does restoring a car this deep in process) , but i think this is great channel. Keep up the great work :)

@CarloGonzales21 5 жыл бұрын

these vids good to watch the background while working👍🏼

@chiefpepdesign 5 жыл бұрын

Fantastic channel. Fantastic work!

@chaack70 5 жыл бұрын

Easely becoming one of my favourite channels.

@jamesexploringonline872 5 жыл бұрын

Thankyou for the positioning of the camera while you were replacing the dif and control rods ex, made it easier to see how you were going about it,, and you and the car, by the end of this project, you'll be able to say a complete restoration in the fullest of the meaning, I'm sure it will not only look good, it should feel better than new. Thanks for sharing this with us, as I said before, your showwing me better ways to go about things.

@luckys1227 5 жыл бұрын

Impressive as always!

@aldodelcorso9712 4 жыл бұрын

Great job guys !!

@michaelandino6281 5 жыл бұрын

Loved your channel already but now your restoring an e30 I love it even more!!!

@yosemitesam283 5 жыл бұрын

I love the E30, my favorite 3 series, very nice work there looks awesome

@bapruis 5 жыл бұрын

I’m wishing I did vids on my E30 Super ETA. Had it torn down the the frame and rebuilt everything. And I was lucky, it has been a California car all it’s life and zero rust...anywhere, which is almost unheard of on E30’s. Well worth the time and all the $$ later on the rebuild. Drives like a new car and with the Toyo rubbers, handles anything I throw it into. Always awesome to see these E30s resurrected in our “club.” They are too special not to give them the attention they love.

@fz9052 2 жыл бұрын

Your technique removing the hub flanges is bloody brilliant :-) Good stuff dude!

@Zamsky39 5 жыл бұрын

Finally somebody who uses hearing protection when whacking stuff with hammer.

@yassinbenlahrech837 5 жыл бұрын

thanks for your sharing your work is very clean

@josecancello590 5 жыл бұрын

Fine job, as always.

@lemig5746 5 жыл бұрын

That was a big, great job!!

@michaelnoschese1153 5 жыл бұрын

I love watching these vids because they are very entertaining but, I also watch them to fall asleep to. Anybody else?

@craig_ramjet990 5 жыл бұрын

Sleep with your chickiebaby, not your laptop.

@maxmontesanto 4 жыл бұрын

Amazing project!

@buzz1854 5 жыл бұрын

youre doing an awesome job man keep it up!

@SmileyDAC 5 жыл бұрын

I like Mecanic Simulator 2018 a lot but watching you do it for real is just so satisfing..

@HT-io1eg 5 жыл бұрын

Huge job! Daunting! Hats off to you!

@RestoreIt 5 жыл бұрын

Thank you! It was indeed.

@simoncl5482 5 жыл бұрын

nice video it's so satisfying to see the final result

@Lordosvk 4 жыл бұрын

My OCD is blessing. Very nice work.

@jamesexploringonline872 5 жыл бұрын

Can't help but to admire you... not just your looks, your abilities in lining up the IRS on your own.. seems you had it well worked out. I have a vy ls1 Commodore, you guys call them vxr8 Vauxhall, looking at your setup it seems similar to myne, I need replace the main Bush's and wheel bearings. You have shown me an ideal way to remove the lower control arm Bush's with the threaded rod washes and nuts, mad as idea, thanks for that one Steve. Well I guess I'll leave you be for a bit lol But all the same, thanks and take care.

@wizz4392 5 жыл бұрын

again pretty awesome video thanks!

@seeman7390 5 жыл бұрын

Love ur videos of E30 ❤️

@mrsafwan7223 5 жыл бұрын

Oh the same jack he restored in previous video cool bro keep it up

@michele55555 3 жыл бұрын

complimenti 👏🏻, quanta passione!

@briangreen6602 5 жыл бұрын

Lot of work to everything yourself , including all the de-rusting and painting - well done on a great result.

@lumazzoni 4 жыл бұрын

This is what I call proper job 👍👍👍👍👍👍

@iivaridark6850 5 жыл бұрын

A few years ago I did that for on MB w124 - went through it completely, the body too... It really was a tough job and took almost 2 years, basically in a yard shed. But positive is the result was so good that there was nothing rust-related under the car for many years and it was wonderful to drive. Old bushings deteriorate from inside out and lose their rigidity long before showing external damage. And, yes, you can do better work on coatings than the factory has done. Takes only time and effort.

@type2523 5 жыл бұрын

I love your BMW related videos !

@Rich77UK 5 жыл бұрын

I love the disc/drum setup. Stops the cooling/contracting disc loosening the handbrake. My 92 vauxhall Senator had similar but the drum outer acted as disc with suoer wide calipers.

@RIOHOTRIO 5 жыл бұрын

SUPER !!! Great job !!!

@hakanyasar8718 5 жыл бұрын

Great work!! Awesome!!

@mitarb7780 5 жыл бұрын

Men you are amazing. This is a very good job. Congratulations. Mitar

@BigConv 5 жыл бұрын

After many a circlip removal on Aircraft Wheels, I found a way of making it slightly easier, if you twist the pliers and your hand one way you can sort of lever the circlip out of place! Hopefully this could help. Love the videos too, keep them coming!

@LeonardoCostaUSA 5 жыл бұрын

awesome job man!! you are crazy.. love the boss inspection ha ha ha!!!

@lordvengerx 5 жыл бұрын

Omg yes I have been waiting and it releases on a Friday to :D

@jimleon7894 5 жыл бұрын

Bloody amazing!

@theblind3899 5 жыл бұрын

Your videos are great my brother...!!

@tigezzitos 5 жыл бұрын

the truth that I admire, the work you do in the restoration of the BMW, beautiful work, you won a supcristor of Argentina, I envy you in a healthy way the things you do, very good congratulations!

@staric4863 4 жыл бұрын

Nice resto. I like the way you work.

@ph7ss564 5 жыл бұрын

Nice video bro.. As always😍😍😍

@RIchardDavidson007 4 жыл бұрын

Why do I love to see the video speed up so fast. Cool video, and learning a lot from the master.

@enriquelopez9124 4 жыл бұрын

Awesome job restoring the E30, I have an E34, 535i I am thinking of doing, you have given me a lot of good information on how to restore the 535i, it,s alpine white with light blue interior.