BMW E46 Rear brake overhaul and dust cover replacment

Рет қаралды 33,802

Brady True Zero

3 жыл бұрын

In this video i replace the rear wheel bearing, rear dust sheild, rear brake pads and the handbrake shoes.

Пікірлер: 38

@davidg.9942 Ай бұрын

learnt something new today,,, mine is rwd so it is bit different, all goes to the drive axle vs trailing arm on yours, had to watch over and over again one part because I got stupid for a moment 😂😂😂

@bigbill74scots 3 жыл бұрын

Pain in the arse job mate. Respect for explaining it so well.

@bradytruezero8739 3 жыл бұрын

Yes it’s a nightmare haha and thank you 👍

@chrish1890 2 жыл бұрын

Really good mate, shows me the parts I missed for getting my garage to do the job. Keep up the good work.

@bradytruezero8739 2 жыл бұрын

Thank you for the kind words 🙏

@jamesfawcett442 Жыл бұрын

Got all this to do in the next few weeks. Good vid thanks

@torquesteer2657 2 жыл бұрын

Well done! We must have done ours at the same time! I spent about a day and half getting mine done in the end. Rounded a couple of driveshaft bolts going into the diff when taking out the driveshaft but managed to knock a smaller socket on to loosen them. Then trying to get the outer race off the hub with the bearing splitter. What a bleedin faff! Still i love working on my cars as a hobby but this nearly finished my back off 😭 Good job mate 👍🏻

@bradytruezero8739 2 жыл бұрын

Haha it’s a pig of a job and thanks man 👍

@rogerhill3984 3 жыл бұрын

Excellent, and no music, perfect

@bradytruezero8739 3 жыл бұрын

Thank you 🙏

@jocalibusohump 2 жыл бұрын

Nice one..My e46 330d on going job.handbrake backing plate broken bearing gone.

@Savage_K 2 жыл бұрын

After all that work u used the old rusty bults and that tired calliper. Thanks for the video doe

@bradytruezero8739 2 жыл бұрын

It is a shame but they where still in working order and as it’s a budget build I’m only replacing parts that are broken or to be upgraded 😊

@philhart3878 3 жыл бұрын

A VERY fine smear of copper on the BACK of the pad will stop any potential brake squeal. (Only if the pad doesn’t have a special coating already)

@philhart3878 3 жыл бұрын

Pull the handbrake up a couple of times to position the shoes before doing the ratchet adjustment.

@neodiy 2 жыл бұрын

spray phosphoric acid on those rusted parts it will be gone and cleaned nicely

@SuperFlash990 2 жыл бұрын

Awesome video. Thanks for the knowledge! I was curious about replacing a dust shield. Would I have to bleed the breaks if I were to replace the dust shield?

@bradytruezero8739 2 жыл бұрын

Thank you 🙏 and no need to bleed the brakes when changing the dust shield 👍

@SuperFlash990 2 жыл бұрын

@@bradytruezero8739 Thank you!!!

@user-ly4uq1ho4h 3 жыл бұрын

Is it a bad idea instead of removing the hub so the dust plate can come off, to cut the dust plate just enough so it can slide out from the side and do the same thing to the new dust shield?

@bradytruezero8739 3 жыл бұрын

That is one way of doing it, the downside to that is where you cut will need to be sprey Ed to prevent rust, my car needed the bearing replacing so done the both the same time 😊

@user-ly4uq1ho4h 3 жыл бұрын

@@bradytruezero8739 Thank you for taking your time to answer my question. You've earned a new sub

@bradytruezero8739 3 жыл бұрын

@@user-ly4uq1ho4h no problem and thank you 🙏

@dinoleonida5486 Жыл бұрын

What kit did you use for this?

@bradytruezero8739 Жыл бұрын

It was a kit from ebay 👍

@veritasaequitas9875 7 ай бұрын

1:17 Where's the rotor?? How did you get the rotor off with the calliper in place???? Were you driving around with no rear brakes? What's that all about?

@bradytruezero8739 7 ай бұрын

The rota was removed before and the caliper put on so it wasn’t dangling

@veritasaequitas9875 7 ай бұрын

@@bradytruezero8739 Ok. Great video man. Covers all the important bits. Like how to do it!!! Where did you get that puller kit and slide hammer?

@bradytruezero8739 7 ай бұрын

@@veritasaequitas9875 thanks man appreciate it and eBay years ago 👍