BMW front axle replacement

Рет қаралды 23,630

Күн бұрын

Please support the channel by becoming a Patreon / bigwillcarcare
Disclaimer
This video is for reference only always refer to manufacturer instructions, advice and proper service manual for actual directions specifications and safe practices when working with tools and equipment. Due to uncontrollable factors Big Will's Car Care is NOT Liable for any misuse or improper usage of Products, Information, Mechanical Equipment, Electrical Equipment, Hand Tools,Power Tools, Ramps, Jacks, Jack Stands, Cleaners, Grease, property damage, injuries, loss or damage that may result from any inappropriate and or improper use of this video and tools

Пікірлер: 20

@E-Sangiovanni 3 жыл бұрын

Great video! I specially liked that you took your time to explain things/steps slowly without crazy music, etc. Thanks for sharing.

@BIGWILLSCARCARE 3 жыл бұрын

Thanks for watching. Please Subscribe if you haven't already. Thanks

@jaquanandrews33 2 жыл бұрын

@@BIGWILLSCARCARE is 9h

@joelane4670 5 ай бұрын

It’s easier to torc that axle bolt when the wheel is on the ground..but really nice video..

@VassiliySmith 2 жыл бұрын

1) Why not make it when wheel on the ground, when try the nut 36mm back out? 2) When you separate control arm, why not to tap from the top of the ball joint? 3) Why exactly do you use rubber mallet for release back of axle?

@BIGWILLSCARCARE 2 жыл бұрын

@Vassiliy Smith There are a few ways it can be done. In this instance was not able to remove the axle nut while wheel was on the ground or to hit the ball joint from the top and i use a rubber mallet more for comfort and controll. My videos are geared towards using hand and common tools the average person have at their disposal which Is why I try to avoid using power tools and air tools. Thanks for watching please Like and Subscribe if you haven't already

@waynetomlison7735 2 жыл бұрын

great job

@BIGWILLSCARCARE 2 жыл бұрын

@Wayne Tomlinson Thanks for watching please Like and Subscribe if you haven't already

@arthur1920 3 ай бұрын

Do you need a DEEP 36 mm socket or will a regular 36 mm 12 pt be enough?

@BIGWILLSCARCARE 3 ай бұрын

Deep socket is best but if the regular socket sits all the way on the nut with the driver it should be fine. Thanks for watching please Like, Share and Subscribe if you haven't already

@craigmclean5868 3 жыл бұрын

Great video! I'm working on my sons 2008 BMW 535xi right now and I'm have a hell of a time getting the cv axle all the way in and seated. Where did you hit it at?

@BIGWILLSCARCARE 3 жыл бұрын

@craig mcLean I just signed it up as straight as possible, twist it and use the axle shaft itself along with the flexibility of the boot to tap it in just make sure not to pull it too far away from the boot or it will separate

@craigmclean5868 3 жыл бұрын

@@BIGWILLSCARCARE thank you. I ended up getting it in by straighting and compressing it then hitting pretty hard. All seems well but I hope i didn't hurt it getting it in.

@24-Paparotzy-IDTR Жыл бұрын

Getting the Axle out on my 08 535XI is kicking my ARCE! I'm just trying to replace the oil pan gasket!

@danielmarjanovic9957 3 жыл бұрын

Is this the same process for a 2014 bmw 750li? My passenger side boot is leaking and making popping sounds when turning.. do I replace the whole axle or just boot

@BIGWILLSCARCARE 3 жыл бұрын

It's not recommended to drive on a bad CV axle. However the procedure should be similar

@BIGWILLSCARCARE 3 жыл бұрын

Thanks for watching please Subscribe if you haven't already

@dflex4180 3 жыл бұрын

Too late to replace the boot once its clicking u need to replace the whole axel