I deleted my 2002 R1150R 3 yrs ago and had no issues at all. 4000 canadian for a new one and about 1100 can for a rebuild with a very long wait. It stops perfectly. You have to maintain the circuit board for the lights and brake lights. Its well worth the effort.
@PappaKostaАй бұрын
I cut out and sealed this one up from the elements and everything worked perfectly.
@gpzturbo9584 Жыл бұрын
This method also works on the K1200RS. By separating & retaining the electronic module, the lights do work. Cheers.
@briankrahnert7218 Жыл бұрын
Nice. Snap, same colour as mine. In process of crap rider anti lock control removal.👍😊
@glennd36182 жыл бұрын
Great video. I have a 2002 R1150RT that I am about ready to perform ABS removal on, being that my model is identical to yours, 1. could you please confirm that your have had no issues with the speedo and brake lites working, also 2) did your servos just stop working altogether (that is what mine did, no other symptoms)? Thank you!!!
@PappaKosta2 жыл бұрын
My servos gave out when I was coming to a stop. All my lights and spedo work. ABS warning light is on, removed bulb. Replaced all lines with galfer stainless.
@glennd36182 жыл бұрын
@@PappaKosta Good to hear your lights and speedo work... thanks for the quick reply, now a lot less nervous about this!
@carguybd2 жыл бұрын
Just a word of caution having done this- an 1150RT is an old bike, and as long as you have things apart, I highly, highly recommend you replace your brake hoses as well. I found out the hard way, my front brakes absolutely locking up in a corner and causing three cars to narrowly avoid me as I fought valiantly to keep the bike upright, that hoses deteriorate from the inside. Did the increased pressure from the new system act as the catalyst to this event? I dunno. I nearly lost my life due to this oversight. Whether the lockup under power, which seizes your engine, toasted my drivetrain? I will find that out in upcoming months.
@PappaKosta2 жыл бұрын
They are all galfer now.
@theswede12763 жыл бұрын
Thanks for the vid seemed like that job was pretty involved
@PappaKosta2 жыл бұрын
It kind of is, but it's more time consuming than difficult.
@kevinmcdonald64462 жыл бұрын
I have a 1997 R1100R. Is the electrical part of this the same for my bike as it is for yours? What I'm asking is will my brake and tail lights still work? Thank you, and thanks for the video.
@PappaKosta2 жыл бұрын
No problem, can you send a pic of your brake controller box? I'm 99% sure they're different.
@kevinmcdonald64462 жыл бұрын
@@PappaKosta Will do. Thank you.
@richardlewin3611 Жыл бұрын
I don’t understand the situation described by the person below who nearly got themselves killed. Is that bad riding or the bike? I ride other bikes and have ridden loads without any ABS and never locked the front up in a bend. Pappa- do you think you could describe in detail what it was exactly you did with the electric unit you removed from the ABS module? That would be amazing thank you.
@Kowzorz2 ай бұрын
I think it's less a problem with the ABS and more with the specific stock rubber brake hoses. It's common for people to advise changing them to steel braided because they fail.
@ambianceguitare2 жыл бұрын
HELLO WHERE DID YOU FIND THE SMALL U-FORM TUBE TO CONNECT THE FRONT PIPES?
@61fordf2504x411 ай бұрын
You just make them with some brake line and a flaring tool.
@j.w.11826 ай бұрын
I replaced it with a new set of brakelines custom made
@christianf83472 жыл бұрын
Bon,cette opération semble très efficace,mais sans parole, et en englisch. ...J'avoue qu'elle ne m'aura pas été très utile à regarder. 😩
@andrewcmarino3 жыл бұрын
I have a 2004 R1150R with failed ABS. I did exactly the same bypass with front brake and servo unit. Breaks work well without the servo. However I have no brake light or speedometer? Any suggestions, I'm at the end of my witt's.
@PappaKosta3 жыл бұрын
Did you reuse the module on the side of the abs unit?
@andrewcmarino3 жыл бұрын
@@PappaKosta yes and sealed it well.
@lancastermick3 жыл бұрын
Try reading this ... hope it helps... www.ukgser.com/forums/showthread.php/232002-Simple-NO-COST-servo-removal-of-1150-IABS-system
@andrewcmarino2 жыл бұрын
@@PappaKosta the electronics were done since the speedo quit working before removal.
@sharpnr445 Жыл бұрын
@@andrewcmarino Andrew did you figure this out?
@christianl7487 Жыл бұрын
Bonjour Le feu stop fonctionne apres avoir couper les fils electrique de la centrale ???? , bientot en France le controle techinique pour les motos va etre obligatoire , sans ABS je doute qu,elle passe le controle .
@PappaKosta Жыл бұрын
J'ai utilisé le boîtier de commande afin de conserver la fonctionnalité du feu
@PappaKosta Жыл бұрын
Une partie de la boîte est divisée en deux
@priusman12342 жыл бұрын
where can i buy that U pipe in front
@PappaKosta2 жыл бұрын
I had to order it from the UK, I don't remember but it was called an "abs bypass fitting" I believe.
@mikeham5465 Жыл бұрын
All that just to get to the abs part geez o weez
@PappaKosta Жыл бұрын
Yes, I wanted to show all of it so people would kinda know what they are getting into.
@albrighttopover2 жыл бұрын
Geht doch!
@gmcjetpilot Жыл бұрын
You are on drugs working that fast.... Ha ha. My ABS is still working on my 2004 R1150RT. I just replaced the brake lines, pads, bleed and flushed.