I am very impressed, I was worried about my motorcycle when I heard the same noise, it makes sense and it seems so easy thank you very much my friend I really appreciate it you saved me a lot of money
@joeybobbie1 Жыл бұрын
Thank You for Posting this. It Very good Information. This isn’t the Noise I’m hearing in my 2006 R1200GS. But at least I know what that Noise is if I hear it. New Subscriber from Texas. I look forward to your other Videos. Thanks again for Posting this. If all of us GS Owners can Post things other Riders need to know, we will all be better off.👍❤️
@davidschoenoff42624 ай бұрын
thank you , iv got the noise , it comes and goes , and I dont feel the vibration at all the bike rides fine , but it gets more pronounced , and it does sound like its spinning and sometimes it sound like something is also spinning and gets caught and then spit out I thought maybe its the clutch disk maybe breaking up , which isn't making sense to me , but a piece of textile on that narrow shaft and when you shook it around I can hear sound like sormthing hitting a sheetmetal piece something like what that shaft was more of a rattling rather then the thud of a piston or timing chain , thank you , as soon as I head that noise you made with that worn shaft , it was the same rattle almost like a snare drum sincerely David G Schoenoff. DavGoFarMototrSports. Manhattan Beach California
@briansmobile19 ай бұрын
Thanks for your help seeing what this noise is. I have driveshaft spline noise on front section from failed sleeve/boot. And also the textile/rod noise.
@briansmobile19 ай бұрын
82k miles. Confirmed. Clutch rod $75 worn back 4mm and textile $11 is leather-like. Primary noise/concern wasn't driveline splines or U-joints. It was the gearbox oil past due.
@christianriccombeni45282 жыл бұрын
Hola, mi nombre es christian, soy de argentina, y viendo tu video, entendi por donde viene el sonido del clutch. Muchas gracias, ya estaba volviendome loco el sonido del taca taca clutch. Abrazo grande desde argentina. Mi moto es una bmw gs 1200 adventure año 2009.
@GreaseAndGravel Жыл бұрын
I am glad I found your channel! Thanks for the info!
@TheClintmeister4 жыл бұрын
2005 GS, had the noise, but louder. It locked up on a ride. I suspect the input shaft bearing dumped its contents into the trans.
@motonest86333 жыл бұрын
might be
@Heavywall702 жыл бұрын
Yup That’s the noise!
@claywbaker2 жыл бұрын
If I want to replace my clutch rod, would these be the right steps? 1) Remove rear wheel, 2) remove shock absorber, 3) remove clutch rod housing, 4) pull the clutch rod out, 5) insert new clutch rod with new textile, 6) reassemble everything. I have a 2005 R1200GS. I have replaced the pushrods (all were out of spec), both cam chain tensioners (springs were soft), and adjusted the valve lash. The only noise I still hear is the transmission as you described in this video.
@motonest86332 жыл бұрын
Yes you are correct!
@irfaninamdar50713 жыл бұрын
My bike same sound now I found sound thanks for the info.
@motonest86333 жыл бұрын
Glad to help
@BB-cl2qh10 ай бұрын
I am in great urgency to know exactly what I need to do to be able to remove the clutch rod because it is stuck?? Hope to hear back soon!
@AytekSahin3 жыл бұрын
I was looking for this, thank you for sharing 🏍
@motonest86333 жыл бұрын
Thank you, :) I follow your advice and a took a moment to reply at comments
@yamahattr250011 ай бұрын
Changed the rod & the textile bearing with new oem parts. Easy fix, just took out the rear suspension. Noise is still the same, unfortunately...
@MrBestvirginia2 жыл бұрын
The little felt or "textile material" actually serves another purpose: on the 1150s but also the 1200s where the clutch slave can go bad when you don't put your bike in neutral (e.g. at traffic lights), the bearing will be bad over time. Then brake fluid MIGHT leak towards the clutch and not only destroy the clutch surface but also eat away the grease of the splines. Eventually, you will end up with stripped-out splines (when all the grease is gone). The felt is to somewhat stop the brake fluid (I know: for the 1200s it's hydraulic fluid)
@rodneyemmerich88284 жыл бұрын
Great video 👍👍
@motonest86333 жыл бұрын
thx
@stevenpailloux6988 Жыл бұрын
Good morning, Thank you for this video and these details. Having the same noise on my 2004 R1200 GS, can we disassemble this part without disassembling the clutch because I tried by removing the receiver but the part does not come ... THANKS. Steven.
@yjkim6065 Жыл бұрын
Great Information!! I had a same noise problem in 2014 r1200gs Liquid Cooled 67,000km. Is the same reason on this of clutch rod textile material ? I had changed the clutch plate and pressure plate yesterday, but this noise is still alive.
@Tattytyres4 жыл бұрын
Great video very professional. Can i ask you a question? I have a 2007 bmw r1200gsa 40,000miles on bike, i changed engine oil and i found small brass looking particles in old engine oil, would you know which component could be wearing in engine , thank you
@motonest86333 жыл бұрын
It can be a lot of things, I would suggest to use a magnetic drain screw at the oil bath. in this way the small metal particles will not travel trough you engine. But nevertheless there is an oil filter as well who suppose to do the job
@Kolhozneg2 жыл бұрын
Rattling noise is coming from the damper of gearbox input shaft
@btxpres991211 күн бұрын
How do you fix it?
@TheRogermursick3 жыл бұрын
would my R1200c have a similar noise. I'm hearing a 'new' buzz, vibration, that I've never heard before and can not locate it. It's not bad but different. I've owned this bike for 19 years and no her 'normal' sounds. And thanks for posting the video.
@motonest86333 жыл бұрын
I've done a clutch change at a r1200c years ago. I general is the same principle. The problem at that motorcycle it was the clutch actuator cylinder. They (BMW) use to recomand Dot4 as a clutch fluid but in time it looks that dot4 is damaging the cylinder and the clutch fluid it goes on clutch plate and disk. At the upcoming models BMW used mineral oil.
@motonorge11723 жыл бұрын
Hello, must that felt stand heat? Could it be anything replacing it
@BreabanMarius6 ай бұрын
Hello! I have a 2004 BMW R1200GS motorcycle, and I have an issue with the clutch. Specifically, on warmer days when I ride in the city and beyond, as the engine heats up more, I can no longer shift the gearbox into neutral. It's as if it doesn't find neutral anymore and feels like something is snagging. Also, during that time, when I fully pull the clutch lever, I feel like the clutch doesn't disengage completely, and the motorcycle tends to pick up speed. Could you give me an idea of what might be defective or what I should do?
@motonest86335 ай бұрын
Marius schimba uleiul in cutie, Castrol sintrax full sintetic . Vezi daca mai face desi eu cred ca nu . Cutile alea sunt destul de bune deci sansa sa fie defecta e cam mica
@BreabanMarius5 ай бұрын
Multumesc! Am sa incerc si revin. @@motonest8633
@mau65able2 жыл бұрын
Thanks a lot for video. Please, where i can get this book you show?
@motonest86332 жыл бұрын
Hi is the Haynes manual but I think you can get it online in a pdf format
@ardeiutzu2 жыл бұрын
Hello :) Except that rod noise that I think all of us has it I wanted to ask you where did you get throttle body protectors, plastic protector over the throttle body? Thank you, Andrei
@motonest86332 жыл бұрын
Salut Andrei , de la wunderlich dar le-am facut eu o adaptare sa se potriveasca la fix , ca nu pusca perfect
@ardeiutzu2 жыл бұрын
@@motonest8633 Da, ulterior le am găsit pe un site din Ro, tot wubderlich dar apar ca fiind compatibile cu modelul k25 2004-2012. Hmmm
@motonest86332 жыл бұрын
@@ardeiutzu dupa ce le cumperi o sa vezi ca nu se potrivesc perfect , plasticul ala nu sta perfect. Eu l-am modelat pas cu pas folosind un pistol cu aer cald. acum e la fix
@ardeiutzu2 жыл бұрын
@@motonest8633 Salutare, revin la zgomotul de ambreiaj. Am schimbat tija+banda textila si nu este nici un fel de imbunatatire, ba din contra. Acum pot spune ca se aude destul de tare si in mers la un mers normal, pana in 3000rpm. Zgomotul tinde sa devina destul de metalic in mers... Ma poti ajuta cu o lista de piese ce trebuie schimbate? multumesc, Andrei
@motonest86332 жыл бұрын
@@ardeiutzu IN cazul in care ambreiajul tau este foarte uzat si ai uzura si la placa de presiune atunci trebuie sa schimbi si placa ca sa scapi de zgomot . Practic trebuie schimbat tot kitul .
@user-vm3bg8kl2c2 жыл бұрын
R1200gs 2004 Rear Disc Talk Price
@jeroenliegeois49533 жыл бұрын
i have a 2006 R1200S, with a similar rattling noise. can i assume these engine are the same?
@motonest86333 жыл бұрын
Yep
@elverdaderoamordedios74953 жыл бұрын
Hello friend, I am writing to you from Chile. Ask: can I only remove the bmw1200gs clutch push rod or does it affect the disc? it's just to check your status
@rubengomezocana59742 жыл бұрын
Puedes, sin ningún problema. Es muy sencillo, desmontando amortiguador y el piston actuador del embrague. No afecta al disco.
@christianriccombeni45282 жыл бұрын
Actualmente mi moto tiene kms 161.000
@fleetwarrior75 Жыл бұрын
My 1150 makes this noise
@hb3yyr4 жыл бұрын
No no no
@mikkei35322 жыл бұрын
Quality of materials BMW is made of is poor - for example steel - compare to Honda - this cluch Push rod in honda is made from Hi-carbon steel and it never wore....... not like in this bike...... This is real change between BMW and Japan bike - quality of steeel and hiprecision of part ( CLUE : bmw is crap)
@tomthompson7400 Жыл бұрын
its not reflected in resale values ,,, just saying ,,, hondas are half the price of bms