BMW R1250 GSA | Want more comfort? How To Install Wunderlich Bar Risers

Рет қаралды 30,607

GearTorque

3 жыл бұрын

Get a better riding position.

Пікірлер: 34

@etmbcrew 3 жыл бұрын

just give an update on the risers... I went for a ride after this vlog was made.. WOW the risers have made ridding more enjoyable.. and it was outstanding before

@gokusupersaiya8067 3 жыл бұрын

what is your height? my height 174 cm .

@etmbcrew 3 жыл бұрын

my height is 180cm

@TheSilmarallion Жыл бұрын

@@gokusupersaiya8067 I am 175 and they are great. I fitted a set on my bike and really it feels like I am on a light dritbike. Elbows nice and bent shoulders relaxed. Also pain in shoulder gone.

@jackielewis996 3 жыл бұрын

Good top tip xx

@GearTorque 3 жыл бұрын

Glad you liked it

@100Thesniper 2 жыл бұрын

i have just fitted a set of these, one draw back for me i can no longer use a tank bag as the bars down now do a full turn, maybe it’s because the adventure tank is higher

@Antizou 2 жыл бұрын

Thanks a lot for the great video ! Just one question could you tell me what’s your height ? and which version of the risers you installed, Wunderlich Ergo+ 38mm (38mm rise and 27mm pull-back) ? Thanks a lot

@michaelnewman5 2 жыл бұрын

much more comfortable happy days but I had to move my cables to the outside of the folks to stop them from being damaged.

@user-kp7mu7iu9h 17 күн бұрын

Спасибо, очень понятно.

@guydarby705 2 жыл бұрын

HI would be rising my bars up and back affecting my tank bag when turning my handlebars

@robertoperetto1321 3 жыл бұрын

Great

@GearTorque 3 жыл бұрын

glad you liked it. thanks for watching. 👍

@ericstephenson3607 3 жыл бұрын

Just going to ask the same question about the cables.

@thegirlinleather3543 3 жыл бұрын

Why didn’t you use a torque wrench? I NEED to know how to use one...as long as I don’t break a nail 😘

@DimitrisNiktos 2 ай бұрын

The brake cable, turning the steering wheel all the way to the left in the lock position is not a problem? There is a solution; Thanks!

@jarosawskrzypek1373 2 жыл бұрын

Which torx is needed for this job?

@scottmathisen9698 2 жыл бұрын

Great video...thank you. Do you have the Wunderlich part number available? Thank You

@etmbcrew 2 жыл бұрын

Hi sorry no.. these we're bought from nippy Norman's

@spangoz1000 2 жыл бұрын

You should have moved the bars from lock to lock, to check for cable clearance 🙄. I know they say the standard cable length is fine, but for safety you should have checked 😉

@GearTorque 2 жыл бұрын

Hi Steve. Thanks for the comment. You are totally right. Unfortunately I forgot to put that in the video. Appreciate the feedback. Ride safe buddy.

@brents1643 11 ай бұрын

You cant get these in the US?

@NorthernBiker-t9h Жыл бұрын

I noticed that there is a gap between the upper and lower clamp (at the bottom bolt) Mine is like this too -is it normal to have gap between the two clamps when fully tightened?

@blademeng5368 Жыл бұрын

Yes, the upper one should be tight to the bar, and the lower clamp should have 3mm gap :) this is what introduction book tells.

@cozydram1 3 жыл бұрын

how was your cables were they impeded at all?

@GearTorque 3 жыл бұрын

Hi Phil. Sorry for the delayed reply. Happy to report there are no problems with the cables. Everything works as it should. 👍

@mobeyond 2 жыл бұрын

is your front break tubes and cables been stretched by front fork ?

@michaelnewman5 2 жыл бұрын

mine did and I had to move them to the outside of the folks so as not to damage them ok now.

@GearTorque 2 жыл бұрын

hi jie su. we’ve done this on this bike and a 2017 gsa and haven’t needed to move the cables on either bike. hope that helps. thanks for the comment 👍