Wunderlich bar riser install BMW R1250GS

Рет қаралды 19,843

Күн бұрын

Nippy Normans kindly sent me the Wunderlich bar risers, to do a video install.
Cost approx £99 and have German Type approval.
Consider bar risers if you can't get a comfortable riding position, having changed seat height, bar, peg positions first.
NOTE I AM NOT A QUALIFIED MOTORCYCLE ENGINEER, ALWAYS CONSULT A QUALIFIED PERSON IF UNSURE.
Nippy Normans Wunderlich bar risers
www.nippynormans.com/r1200gs-...
Wunderlich website
www.wunderlich.de/shop/en/wun...
It will take you 10 minutes.
Very nice quality. All cables remain.
If you have already put them on your BMW, please leave comments as to how you got on with them. Better? Worse? Height etc for potential purchaser's.
00:00-00:31 Introduction
00:31-00:45 tools required
00:45-01:25 what's in the box
01:25-03:03 removing handlebars
03:03-08:25 Installation
08:25-10:02 Final bits / checking bars etc
Further info of handlebar position :
How to position your handlebars properly - Brake Magazine
• How to position your h...

Пікірлер: 62

@brianrundle9219 2 ай бұрын

Clear and concise instructions without any annoying music. Spot on!! Many thanks

@martin9756 Жыл бұрын

Your videos, presentation and attention to detail are superb. So pleased I found you on KZfaq as you gave me the final 'nudge' I needed to decide to buy a GSA. Already specked out, placing the order in the New Year for a March delivery. Intend to do my own 1st Service and then first tour to family in Lisbon in April. Please keep up with the videos and commentary - so good. 👍👍

@gsd32i Жыл бұрын

Thanks Martin , loving the GS . I have just ordered an sc project titanium exhaust and will do a video on that when I get it . I ordered one because I could 😂. Thanks for the comment and taking time to post it 👍

@markg1291 4 ай бұрын

Just installed the bar risers on my 2022 R1250 GS and the installation was a dream. Thanks for the video. Very helpful

@gsd32i 4 ай бұрын

Glad it helped

@maciejmaciej1718 Жыл бұрын

I've just followed your instructions and I've successfully installed my bar riser. It would be just worth mentioning that if you drop your handlebar too low, it will hit a tank when you take a sharp turn. Cables may also be stretched too much. It happened to me and I had to raise a handlebar a bit. Also, I used only 45 torx bit, You mentioned number 40 was needed as well but all screws are rather 45? Best, M

@brianhill3603 Жыл бұрын

I'm suprised NM sending you bar risers for free to review given they aren't exactly a new product, for what it's worth the Ebay ones at a third of the price do exactly the same job.😎

@gsd32i Жыл бұрын

Brian they just wanted me to fit them as some riders have had issues. Everyone has a choice ref budget.Ride safe 😁

@hrmacdonald4471 Жыл бұрын

Nice install...why did you feel risers were necessary. I like the idea of torquing to company specs. I want to buy a smaller torque wrench and wondering what one you are using. Thanks again for all the great videos & content.

@gsd32i Жыл бұрын

Thanks. Nippy Normans just wanted me to do an install video and this will end up(I suspect) on their site, so they sent me them FOC. I would consider using risers if I were going to do some off road stuff as the standard bars for me, bring me too far over the front of the bike making it uncomfortable . The standard bar set up is great for me as I do road riding mostly. I am Mr Average size but taller riders etc may need risers. I will try the risers on and off the road in the next few weeks and see what I think overall and whether I go back to standard config. 🤪

@tomaszsydney7730 Жыл бұрын

Cześć możesz podać gdzie wkładam śruby dłuższe a gdzie krótsze śrubyJakim momentem Nm dokręcasz śruby?Pozdrawiam.

@praveennair5588 Жыл бұрын

Hi , Thanks for the video 😊. Just checking Is it necessary to reroute the clutch cables for raising the handle bars. I saw it in few videos. I have done the same way you did for my r1200r.

@gsd32i Жыл бұрын

Hi . I didn’t have to route anything . Not sure if 1250 cables are routed same as 1200r though .

@praveennair5588 Жыл бұрын

@@gsd32i Thanks for your prompt response.

@terenceokeeffesmotorcyclestuff Жыл бұрын

Cheers 🍻. What was the removal/replacement of the cable tie achieving again? Was there a cable relocation?

@gsd32i Жыл бұрын

To be honest I was following Wunderlichs destructions! ref cable tie so can't give a definitive answer to that one. No cable relocation needed.

@TheDervMan Жыл бұрын

Will you do a follow up vid of how they changed the riding position/comfort?

@garysmythe9545 Жыл бұрын

Yep would appreciate advice on improvements

@gsd32i Жыл бұрын

I will try and do one this week if I get time, wife has a long list for me!

@anthonyrobinson782 2 ай бұрын

Followed your instructions and raised my bars, great instructions but can I ask why you took the old zip tie off just to put another on

@gsd32i 2 ай бұрын

Not sure TBH 🙈, glad the instructions helped.

@niall5181 Жыл бұрын

Get vlog as usual..can I ask are they standard mirrors on your GS cheers

@gsd32i Жыл бұрын

719 mirrors

@Rezaroth Жыл бұрын

Thank you for the video. I watched it and bought the risers after that. But when I installed it I saw that when I turn the bars to the far right the clutch line becomes stretched. Could you please tell us if you have the same think on your bike? Mine is a GSA 2021 model. Thanks

@gsd32i Жыл бұрын

Hi, although the cable was pulled slightly, it wasn't a problem at full lock. I don't know if the GSA has an issue as mine is just the GS🙈

@Rezaroth Жыл бұрын

@@gsd32i Thank you for the reply. Mine is a bit concerning. Only the cluch hose though.

@clintlewis1719 Жыл бұрын

I ended up having clutch hose issues. The clutch assembly was too close to switch gear. Move it out to white line on the bar to fix this issue

@gsd32i Жыл бұрын

Thanks for the input 👍

@phatlakersfan1 10 ай бұрын

Can you elaborate on that? What kind of issues and what white line? Thanks

@tomaszsydney7730 Жыл бұрын

Hi, can you specify where I put the longer screws and where the shorter screws? What torque Nm do you tighten the screws with? Regards

@gsd32i Жыл бұрын

The shorter head screw goes under the handlebars. 19 nm

@DUKim-mk8fo Жыл бұрын

If the cable tie is relocated, Can handle interference be avoided? Now I'm having interference problem turning the handle all the way. so, I am going to relocate cable tie as a test.

@gsd32i Жыл бұрын

On my 2022 GS I had no issues , is yours the GSA ?

@eesqui11 Жыл бұрын

Hi, I have a question, I have a GSA 2023 and I bought the handle risers but the left side where the cables are stretched, however I didn't even have to do anything on the right side since the cables on that side are very loose. any suggestions? thank you so much

@gsd32i Жыл бұрын

Hi . Have you tried a combination of rotating the bars and moving the angle of the clutch lever ??

@DimitrisNiktos 2 ай бұрын

The brake cable, turning the steering wheel all the way to the left in the lock position is not a problem? There is a solution; Thanks!

@gsd32i 2 ай бұрын

I didn’t have any real issue with mine . 👍

@ThePorts77 Жыл бұрын

Is there any benefit to comfort with bar risers when rising road? I am considering them as when I stand I feel hunched over (6ft). But interested on how you find them for ‘standard’ road use.

@gsd32i Жыл бұрын

Great question. I took out a GSA a few days ago and that had bar risers on and was really comfy for me at 5'9". I have had bar risers on that raise and bring the bars closers to you and I didn't find them better than without and the bike felt too different to me BUT the straight forward bar risers were brilliant and I may get some later. I guess if a friend has a bike with them fitted give them a go. Trial and error kind of .

@ThePorts77 Жыл бұрын

@@gsd32i out of interest in what way better, just riding position?

@gsd32i Жыл бұрын

@@ThePorts77 More comfortable in that relaxed riding position.It doesn't take much to change the whole fell, even rolling the bars forward or backward can have a huge change on the bikes feel/connection to the rider.

@robertosacilotto3070 3 ай бұрын

Is it possible to add this riders to BMW R1250R without disconnecting the cables from the handlebar ( they are very tight expecially that of the clutch ) ?

@gsd32i 3 ай бұрын

Apologies, but I don't know.

@desmiller4764 Жыл бұрын

Bar risers again ?

@gsd32i Жыл бұрын

Des I wasn’t 100% happy with previous video , so I did it again and deleted the first one . 🙈

@jorgenjohansson5440 Жыл бұрын

I have mounted the risers accordingly and found that the cables on the left hand side are too short. I wrote Wunderlich and they replied that they will look into it but not any time soon. I am surprised that it works on your GS, is it a 2022 GS?

@gsd32i Жыл бұрын

Hi Jorgen, yes I have the 2022 gs and the risers are fine, although on full lock the clutch cable is just starting to take up the slack, but doesn't cause me an issue. Possibly try rotating the whole switch gear/clutch unit around a bit ?

@jorgenjohansson5440 Жыл бұрын

@@gsd32i Thanks for your reply! I have sent pictures to three dealers now since I can only move the handlebar around 60% to the right then the cables are at their maximum. I have tried now two times just to be sure. Not possible on my bike without cutting/changing all wiring. I have a 2023 GSA which is practically the same as the 2022 and 2021.

@gsd32i Жыл бұрын

@@jorgenjohansson5440 Ok. Best of luck, mine is a GS not GSA. I think the GSA has longer front forks for going off road, that may be why.....but no real issue with mine. Were yours the same bar riser?or a larger one?

@jorgenjohansson5440 Жыл бұрын

@@gsd32i The very same. Wunderlich, SW-Motech and Motea have the same "up and against you" risers with exactly the same measurements and all of them say "it should work"....but as said earlier, they will check themselves

@gsd32i Жыл бұрын

@@jorgenjohansson5440 OK , Hopefully something simple. Have any friends got the same riser? Try swapping?