BMW R75 CAFE RACER 2.0 BUILD EPISODE 7 / VELOCITY STACKS, CONTROLS, MOTOGADGET SWITCHES, MIRROR

Рет қаралды 27,013

Күн бұрын

This week we make a velocity stack for the Dellorto Carbs. Then we mount all the controls (Mirror, Motogadget Switches, Clutch lever, Brake master and Brake lines.
Motogadget Switches
cognitomoto.com/search?type=p...
Biltwell Grips
cognitomoto.com/products/bilt...
Clutch Lever
cognitomoto.com/products/clut...
Mirror
cognitomoto.com/collections/n...
Mirror Mount
cognitomoto.com/collections/n...
Clutch Cable
cognitomoto.com/collections/n...
Cable Lever Nipple Holder 8mm
cognitomoto.com/collections/n...
Clutch Adjuster
cognitomoto.com/collections/n...
Brake lines
cognitomoto.com/products/gsx-...
0:00 Velocity Stacks
2:05 Tag
3:15 Right Handle Bar
5:44 Clutch Lever
8:27 Motogadget Switches
9:38 Motogadget Mirror
11:40 Clutch Cable
12:25 Brake Lines
13:25 Chat

Пікірлер: 24

@jamesrwight401 3 жыл бұрын

Devin: the cleanest bike builder...as referenced by his continued attire of button down shirts, and anything but garage gear lol. Bravo.

@kimjon3774 Жыл бұрын

Beautiful engineering and video production. Thank you for posting this content

@Thewatson77 3 жыл бұрын

Super sharp looking so far. I agree with you about the mirror ; sucks that it can’t go underneath. It just doesn’t look right up top

@gregzastawny8440 3 жыл бұрын

Just wow, im impressive!

@crazy1pi Жыл бұрын

Nice series

@mrbookends 3 жыл бұрын

Immediately thumb's up but haven't watched the video yet - got to be engaged in my work conference call and THEN I'll knock this bad boy out!

@loganbrown2117 3 жыл бұрын

So you can just make your own air filters like that? It’s really that simplistic? My life is all a lie wow. Great craftsmanship throughout the whole video!

@kabeemer 3 жыл бұрын

Clean build, BTW, wonder why you are not working on a RE650, I would like to see an Enfield similar to your XS650 credentials.

@JMVENTURES1523 2 жыл бұрын

Where did you get that throttle assembly?

@devincalhoun3792 Жыл бұрын

What I’d love to know, as I’m new to rebuilding motorcycles (just started mine about 6 months ago….2013 Moto Guzzi v7 Racer), is with regards to aftermarket switches like these in the vid. I’ve come to learn these are referred to as “momentary contact switches” so my question is are there OEM switches/buttons on my v7 Racer (or any bike I guess) that cannot be replaced by these aftermarket switches? Lights and starter button are what come to mind as the current OEM switch turns them on until I turn them off, so they are not momentary. Or am I being too literal in my understanding of a momentary contact switch? Thanks in advance for any help……and loved this video.

@CognitoMotoTV Жыл бұрын

Correct. To run these momentary switches you really need an m-unit

@davidmuir6849 2 жыл бұрын

Hi Super clip Im looking at fitting the same grips on my re gt650 did you just bin the bar end weights completely ? Regards Dave from Scotland

@CognitoMotoTV 2 жыл бұрын

They are pieces of plastic in the end of the bars. They are not really weighted ends.

@davidmuir6849 2 жыл бұрын

@@CognitoMotoTV Thanks Ill bin the weights and fit the gt grips Cheers Dave

@nerfhringnun2098 Жыл бұрын

what combination switch are you using

@aaronpadilla3541 3 ай бұрын

Is necessary the M button ? For the switch's? I want to install just the switchs!!!!!

@CognitoMotoTV 3 ай бұрын

You dont need the m-button. We did not use it here. You do need the m-unit because these are momentary switches.

@Mike-up4uf 3 жыл бұрын

Which brembo unit is the front master?

@CognitoMotoTV 3 жыл бұрын

This is actually from a Thruxton R. The R6 has a brembo as well.

@Mike-up4uf 3 жыл бұрын

Nice!!! So is The adjustable clutch lever and perch also from a Thruxton?

@sanderziugov 3 жыл бұрын

Why didn't you turn the stacks instead? A lot less effort and setup. Great stuff tho.

@CognitoMotoTV 3 жыл бұрын

Since it was just two the setup and fixturing to do it on the lathe would take more time than just doing it on the mill. When it goes to production it will be turned on the lathe.

@sanderziugov 3 жыл бұрын

@@CognitoMotoTV fair enough. I'm running the lathe most of the time, therefore when ever I see something that can be turned, I'll turn it.. I'm also doing bike stuff, you can check out my instagram, if you like: allthings_zed