I've always been a bosch fan. All my battery tools are bosch. i bought one a while ago and it was weird at first but i'm getting use to it. Very nice and i found it vary useful with my work.

Finally, someone that demonstrates torque!

You have a good eye for good products

Awesome screwdriver

Nice review!

Im sadly reporting that the electronic clutch (torque limiter) is so high that even the lowest setting will damage any electronics, computer cases and even plastic household appliances. This tool is useful for carpenters and alike only

thanks for your reviews . you pay attention to details that others do not . plz add link for buyers . thanks

I am still deciding between this and Black and Decker KC4815. Tough one

Buying this after watch this video thanks !!

is this better than bosch ixo iii screwdriver?

thumbs up for this review

This has been posted in lazada as an introductory price of 1,111 in the lazada 11/11-12/12 sale,. Regular price is 2,999 as of today dated December 1 2017.. Hope that this will be discounted again for the 12/12 sale..

You can install a 4 inch hex extension adapter and used it as a regular screw driver . The bits used are standard, milwaukee, makita, ryobi, dewalt, kobalt, hitachi, ridgid , craftsman, porter cable, black and decker, harbor freight tools all adaptable , brushless? amp hours, ?charging time,?

Hi, is this 3,6 V? and the new Dremel go exact the same but 4V? Thank you.

I'm planning to buy this one. I hope Ace Hardware here in Bacolod has this available

Can you review Cloudware's Cloudpad Titan or Cloudpad Classic? I'd really like to see some recommendations for tablets under 5k :)

Thanks for the review! What is that clicking sound when you were using it manually (around 2:00 mark)? Is it a torque clutch or something?

It's cool but do they have an extended version? The bits seem kinda stubby and short for deeper pockets

I badly needed this..

can you replace its internal battery? like in some cellphones you could open to replace battery.

Are the bits magnetic?

Where did you bought it? and the price of course... 😒

its only for straight operation it will fail if you try with some attachments like universal joint 45degree you dont have any way to press down the driver thats why it need a button to run it

Good day sir, is the lowest torque setting safe enough for use in circuit boards or pcb's?

Hi, where did you order it from?

I use this Bosch/Dremel Go screwdriver. Fast and powerful tool. But: 1. Torque is bad. Hard and not controlled. It turns around in our palm at the end of tightening the screw, therefore dangerous. 2. We can’t use this tool during tightening and removing small screws by pressing the tool to run. The act of pressing may be softer. 3. Drill bits get away after drilling and we are obliged to remove by our hands... What can we do to soften the torque?

you did not mention the price.

i bought the new bosch go 2 but they dont include the charger also they dont reply what adapter should i use to charge it ... XD

Didn't show torque adj.

Available in Lazada

If I don't win this from your raffle. I am buying one from Lazada as soon as they have stocks.

reverse? is removal of screw supported?

where you buy? this?

I want 1 :)

no wonder your voice sounds familiar

I want one

Sometimes I think the thing is too powerful. Even at the lowest torque setting it manages to strip the screwhead if you don't stop pressing.

Minus well get the Dremal go-01 it’s the same like this same design for a cheaper price Bosch is good but on amazon show a difference in price for the same tool and same function just different name because of marketing

Unbelievable that no major manufacturer has seen the glaringly obvious sense in doing away with the need for a switch to operate the tool - until now.

tear down please....

It would be better if they include a led

I just bought it for 39,99 Dollar from Gearbest.

Bad driver... the motor has no brake, making it difficult to control. The switch is often accidentally pressed.

I bought one, and I hate it. This thing is a real piece of crap. Nothing to hold the bit in, so get the tape out. Almost impossible to use except in a completely practiced repetitive task, but still not worth picking up to use ever. I really tried, with total frustration each and every time I tried. Bosch has gotten so bad in their designs over the last 10-15 years that I will never buy another Bosch tool as long as I live.... and I used to buy nothing but bosch.