Great vid. You just saved me a trip to the mechanic. When you said “more torque”, I said, “ you mean leverage buddy”…then you corrected yourself. Too funny.

Why do I picture this guy wearing a velour jogging suit, white Jordans and a thick gold chain? Excellent video!

Thanks so much for this upload! Getting ready to install a performance brake kit on my TSX next weekend and was worried because I don’t have anyone to help me. This saves me a lot of pain in bleeding the brakes.

Thanks for making this instructional video on how to flush your own brakes solo! I got the same bleeder bottle years ago and I'm just now starting to do it myself instead of leaving it to mechanic shops. I have a spill-free funnel from back when I changed out the coolant, might use that to just keep the master brake cylinder reservoir topped off.

Thanks for the great video, I ordered the bottle based off this video. I have 3 cars to bleed and it will go through a lot of use!

Great video! This thing is pretty good I just used it to bleed brakes on my old landcruiser. I have to do it again as the fluid is still pretty dirty but I definitely appreciate your tutorial to make sure I don’t forget anything when I’m able to get back to it again.

Great timing. I picked this one out of all the options I saw online. It just came in. Using it this week. Your video confirms my thoughts on how to use since it didn't come with instructions. Thanks.

8:40 nice sounding motor 9:00 sirens LOL. Just bought one of these bleeder bottles, thanks for the information.

This was the most helpful video on this, thank you. That bottle is the real deal.

The Brooklyn acent takes me back to the East coast. I used to live in NJ and Brooklyn myself! Great detailed video my brother! I just bought one of these bottles, and I'm doing a TSX caliper upgrade on my Civic Si, and installing new SS Goodrige brake lines very soon. (Weekends are super packed for me)

Just ordered one of those bottles. Thanks man.

NO air escapes around bleeder. But it enters through the bleeder threads when you unscrew it and depress the pedal. Much better to have a pump on top of the brake fluid reservoir with constant pressure. That way NO air can enter the brake system, since the pressure in the system only forces it out, never in.

Great video. Succinct and informative. One tip, brake fluid is very caustic. You wanna put towels down to cover everything around the master cylinder and clean up your caliper wheel area from any drips as well. You dont want even a drop finding its way onto a seal or belt or rotor.

You just convinced me this the one I need not the pump bleeder. Thanks 😊

Really great video.. I purchased 5/16 OD 3/16th ID clear tubing at the hardware store. 10 cent a ft for 4ft,, I drilled a 5/16th hole in a Gatorade bottle cap and a small air hole in the cap Then I pour fluid into the bottle approx. 2 inches , slide the hose thru the hole down to the bottom of the bottle, I then put a tie strap under the cap around the tubing so it cant pull out,, I also apply a small amount of silicone Brake grease around the base of the bleeder screw to stop air entering the system. Cost with out fluid less than a buck.. This video he did is awesome, im just tossing in some extra ideas...

Great video, going to do mine soon. Thanks!

The fluid was definitely dirty based on the dark color. Good video. I have done this with a Gatorade bottle.

There is a Box Bleeder (6 point) made just for the job for about $10. It comes in SAE 5/16 - 3/8 and 8 - 10 metric, and is thin wall and deeply offset.. Alternatively, the next best wrench would be a flare nut wrench, but calipers frequently do not have enough room around the bleed nipple for this.If a person is doing any serious brake work a pair of box bleeders is a must-have.

thanks for all ur video. u help to keep us away from all those Stealership.... keep good work bro

I may need to replace my brake calipers, your video just convinced me to buy this bottle instead of the cheapo 5 dollar ones on Amazon. Cheers.

Solid video, looks like a fresh brake job, If you did not pull guide pins and clean and re-lube, you might consider it in the future. Many (bad) shops even skip doing, that and it only takes 5 minutes a corner. It is super easy and should be done every time a caliper is taken off

Can I do it like this with any car/truck with ABS Brake system?

Cheers Bruv this video helped me a great deal, and I like you little bottle with the magnit on, I wish I could get one in England... Good day fella

Was trying to figure out how to use this bottle and what makes it different from a regular bottle. I guess the difference is that you don't have to keep opening and closing the bleeder valve every time you press the brakes, you can just leave it open the whole time?

Good work Thanks

That fluid looks good compared to what I see at my shop. Many of the cars I see look like used diesel oil.

good video, I like the bottle.. I going to buy one, thanks for the info..

Nice video and thanks for this!. I was thinking Can I do it on my 2016 MDX but with the tires on and not lifted up?.

interesting, how your bleed sequence is different from my first gen mdx. I just looked at my manual.

Thanks for the video!!

Canarsie in the house. Nice job.

arent you supposed to start bleeding furthest away from the master cylinder? Rear passenger --> rear driver side --> front passenger --> driver side

Great job, young man. Keep doing what you do.Can you come to Dallas ,Tx.. and do my brake lines .again great job.

I'm going to make me one of those.

A squirt of WD-40 down the bleeder screw will greatly reduce the torque needed to break it loose, without braking the screw off; I admit I snapped a few off...

Gracias, Loco!

Bro, can I do it same procedure. I have crv 17 touring ABS braking system? Thanks

Does it matter where bottle located? Higher or lower than bleeder screw? Also some videos close the master when doing, does it matter?

when you start, best to suction out as much fluid as you can, then top off before you start bleeding, may as well get the most old stuff out as possible. Also put block under pedal so master cylinder will not travel into area it never has before, and possibly pick up internal grime that never was touched before. 1 quart should be more than enough, but not if you bleed too much at each corner. I think the system might hold 20-24 ounces. Also if you are doing a real through flush, consider pushing caliper piston in with bleeder open as a starting point, that will evacuate a lot more fluid from caliper piston, but there are risks involved in that method.

bro, you want to know how tight that thing is? that thing is TIGHT!

Had to leave a like for a fellow NY'er, great video.

This works for 2017 Acura MXD also?

this was your first brake flush? not that dirty, but its pretty dirty!!!

That accent...Sopranos all the way!!! Expected to see Tony.

Your brake fluid looks new

Did u do all this while the car is running?

Just rear brakes and no front brakes need to do?

Very informative. I just bought an Acura 2014. Im going to follow ur video and tune my car. Thank You

Did you notice a difference with the brakes? I need to do my truck. I've noticed the brakes are a little soft when things heat up. Thanks for the video. Do you start the car when you pump the brakes?

will this work on motorcycles? I want to do a flush and fill on my bike. did you pump the brakes before putting the tube on the bleeder valve? because as soon as you opened the valve the fluid came out into the tube. that's why im asking. or is that how it is when you open it once the tube is on?thanks!

Thanks for your video! I just have one question. Would you mind sharing where you place the floor jack?

You are a pro now my brother and you can charge for your services on this and any other honda, nissan, lexus whatever? you have proven yourself worthy

thanks

THANKS, WHY WOULD U TALK ABOUT A TOOL & NOT LEAVE THE LINK TO THE ONE MAN BLEEDER TOOL? BEST, G E.

Do you even need to step on the pedal ? Seems like this method is called “gravity bleed” without pumping the brakes .

The start says to use an open end wrench, the procedure shows using the box end. Looking at the caliper assembly of the first wheel, the guide pin boots are dirty, the abutment springs (stainless glides) look like they're distorted, not seated and have never been changed. Not service those items is why most brake pads and rotors become damaged

But if the cap is not screwed back on tight when pumping brakes doesn't this push up the brake fluid to be pushed up over the top of the reservoir ,or does it not

Nice bottle the problem that the hose and bottle not clear to see bubbles

Hello, I know you replied on 1 of the question from the viewer stating you used almost 2 of the 12 oz bottle to bleed your brake system but does it mean these 2 bottles of new brake fluid would be enough to stay in the brake system after flushed out the old fluid from all 4 calipers? I want to make sure i have prepare enough brake fluids before I start the this project on my 2014 MDX instead of running out to get more in the middle of the job. Thank you!

Do you release the emergency/ hand brake before you start bleeding ?

The next Tyre and every Weel? Hä?

How many bottles of brake fluid do you recommend to have before starting this job? And you can’t use brake fluid that’s been opened before right?

İts really improve brake performance of the car.

BUSHWICK in the house. Que pasa ? Bro

Did you pump the peddle without screwing tight the reservoir cap back on tight

You want to have the bottle higher than the bleeder but below the master cylinder.

this is fucking great, the accent puts it over the top hahahah

Very good video I have Acura Tsx 2010 I will probably do mine as well after watching this and I might probably go with Prestone instead of Honda's brake fluid

Aaaaaaanddd action starts at 06.00

I appreciate the video. I actually made a very similar video to this one. I still think you did a great job though. I like watching automotive related videos.

This guy 🫣

good video. where can i order that bottle?

How much bottle did u use?

Does car in america use DOT 3 ?? DOT 3 is 20 years old!

واو

y(^O^)y南無阿彌陀佛爸>NamoAmitabha88>南无阿弥陀佛爸>ナモ阿弥陀お父さん y(^O^)y

During the bleeding process, when you're hitting the brakes a few times, do you have the car on? or off?

But "protecting yourself with rubbers" leads to having less pleasurable feeling! Um...what are we talking about here? Brake bleeding or using cond... Anyways, thanks for the video!

That brake fluid looks like someone with bad kidneys 😆. One thing I like do is read the comments on vids I watch. Saw several comments about wear gloves when handling brake fluid, as it can be absorbed thru your skin and eventually can damage your kids. I recond wearing gloves when handling any auto fluid. Got job bro👍. Shout out to BK

Hey tough guy you eva herd of a funnel

empty reservoir all the way

15$??????🤣🤣🤣

15 bucks for that bottle? Are you kidding? I could put something together like that for a buck and a half, and work just as well!

Disaster.

Talk to much an take to long to start stop watching at 2 mins