CAV DPA Build Part 2 Max Fuel Setting & Pump Guts

Рет қаралды 164,635

7 жыл бұрын

Part 2 Rebuilding a diesel injection pump. It can be intimidating, but these CAV DPA rotary injection pumps are very doable with a good kit and some good video instruction. In this video I assemble the heart of the injection pump and the lift pump and explain the max fuel setting.
This is where I got all the parts for this pump rebuild → amzn.to/2rJhqmd
Connect with me socially on these social media spaces
Facebook → briansmobile1
Instagram → briansmobile1
Twitter → briansmobile1
Drop me a postcard or send me a license plate from where you are! You may see it in a video!
briansmobile1
P.O. Box 282
Cedar Valley, UT
84013
Disclaimer:
DO YOUR HOMEWORK before making a decision based on information you find on KZfaq here, or anywhere else when it comes to your car or your safety. Failure to follow this counsel could result in a Darwin Award. While this video is educational, it's up to you to fully understand the topics discussed here or seek advice from professionals familiar with your situation mm kay?
Always wear your personal protection equipment- if anyone asks, tell them your mom dresses you funny and you like it that way.
Please use & apply this information solely at your own risk.
Due to factors beyond the control of briansmobile1 and the general lack of “common sense” in tort law and in this world generally, I cannot guarantee against improper use or unauthorized modifications of this information.
briansmobile1 assumes no liability for injury or property damage incurred as a result of the presentation of this information contained in this here video or any of the other briansmobile1 videos.
briansmobile1 recommends safe practices including the use of personal protective equipment such as eye protection, hearing protection, gloves, guards, shields, and respiratory protective devices when working on vehicles and or with tools seen or implied in this video.
Due to factors beyond the control of briansmobile1, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result.
Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility and to be used at the discretion of the end user/viewer and not briansmobile1.
I am an Amazon affiliate.
And a Prime member and general Amazon nut.

Пікірлер: 65

@johnshere4922 5 жыл бұрын

Hi Brian. Went I uses to rebuild pumps , the pump plunger was check by reversing pressure on number 1 injector pipe union and apply 20 bars and measure the roller with a micrometer. PLEASE NOTE IF MORE THAN 20 BARS PRESSURE APPLIED YOU WILL BEND ROLLER CAMS ADJUSTERS. Spill timing is also done the same way by setting the letter to the circlip grove in the window. Your video is good and minor adjustment can be done on the vehicle on the throttle arm.

@ElementofKindness 4 жыл бұрын

OMG! You sent me into a bit of a panic! After doing battle with my CAV pump for nine days straight, I finally got it working. Then I see you putting a ball in the head locating bolt at the advance. First thing I thought was, "Oh crap! I don't remember seeing any ball!" I ran out in the dark with a flashlight and a magnet, and poked around. Finding nothing, I removed the locating bolt to check on it. Fortunately, mine doesn't have that ball arrangement! 😂😅

@Aint1S 5 жыл бұрын

My tractor has sat all winter, I think either the priming mode spring has indeed gone out or the metering valve is stuck like Chuck! Holy smokes, you may have saved my summer with this one... Week stream on the injectors and it's not pumping high pressure fuel as it should. Gaskets and seals, I'm going in!

@michaelherbert8213 7 жыл бұрын

With all do respect heres some feedback from a long time subscriber.........I miss the car and truck repair videos. I've noticed that you don't make too many of those videos lately. I still love the channel content though but would love to see more of the old school briansmobile1.

@briansmobile1 7 жыл бұрын

Thank you so much for that feedback. I need that. There are so many reasons why I'm doing what I'm doing, but half of it is carrying too much stress, not getting enough sleep, and escaping to things the push and interest me rather than doing what works. You've been there for me, I need to be there for you.

@syazwanwan4338 5 жыл бұрын

thanks broo, good video

@robertmintz63 4 жыл бұрын

Very informative, thanks for the explanation of the amount of fuel, rollers & pistons, but a little to fast , especially at the 4.40 time . You did not show any alignment views through the window .

@jarmokoljonen552 5 жыл бұрын

Hello! Very good video! I opened my regulator valve for cleaning (5:10) and noticed that both springs (2 and 5) were missing. Any idea how strong those are? And where to "lend" them? Usual pen-spring-lending not gonna work? 😂 Cheers from Finland!

@andregross_official 4 жыл бұрын

hey there, nice vid. thanks for sharing your knowledge. one question regarding engine rpm: if id like to raise egine rpm, how do i align the governor springs in the linkage? for example, 2200rpm eqals hole 2 in control arm and hole 2 in linkage - how to set it for say 3000rpm?

@maniekmechanik 5 жыл бұрын

Great explanation video Thanks for it It is great help im a mechanic but dont have much access to do pumps or so but im interested in what way the pumps are build and how they work Thumbs up 👍👍👍

@thelaststarfighter 6 жыл бұрын

Do you think if the return side of the injection pump was clogged with debris it would cause the engine to shutoff? I have an issue where the engine starts and dies. Found debris in the return pipe when i removed it. Injection p ump was just rebuilt. Low pressure pump is good. Shutdown solenoid is good and circuit was load tested.

@andregross_official 6 жыл бұрын

Hi Brian, is it possible to convert a non solenoid pump to a solenoid controlled pump and can you tell me which parts i need to do so? Thanks!

@enriqueorihuela8717 Жыл бұрын

Interesant thank you

@markthompson1134 4 жыл бұрын

I have stripped this pump and the pump rotor the pump then came apart and the rotor adjusting cage came apart from the shaft is their a proper way for this cage to align up

@Farseer1995 Жыл бұрын

Hey, I believe my boost compensator is failing on one of these pumps, as I don't think the pump is upkeping with the demand when on higher revs (when the rubo kicks in, technically). Is membrane replacement possible without any additional adjusting? Or does the pump have to be adjusted after the boost compensator was messed with?

@jdickson242 4 жыл бұрын

Hi I'm rebuilding an old Universal/UTB 550 tractor at the moment. Done a complete engine overhaul. The only thing I haven't touched is the pump but I feel its a good time to service it. I've always been scared off rebuilding the pump. Do you think this is something a moderately skilled DIYer can do?

@JacksonCabalerro 16 күн бұрын

Hi from France! Nice vid ! My tractro doesn't start, I think pump doesn't feed injectors enough, do you adjusting to max can solve the prblem and help start ? Thanks

@giles-df9yu 10 ай бұрын

For years case tractor used the same perkins engine.. same bore and stroke same cam, for the four cylinder. The went all the way up to 95 horse power. All the did was change that setting. Smaller 45 horse tractors had the ability to produce 95 horse power. This was when they were David browns and switched over to case.

@durametalroofing997 3 жыл бұрын

Hi, Is this mostly to seal leaks . My pump needs some internal parts such as cam. Tractor stalls easily and no start when hot. or does it need a bench test after installing new cam etc. to calibrate it. I may be on the wrong video . Correct me on this, Seems like replacing seals is more of diy project vs replacing major internal parts. Thanks.

@irishguy200007 Жыл бұрын

If the ball is missing in the bolt, will this make a difference in working pressure?

@stevenscherrer1076 2 жыл бұрын

If that ball inside that bolt falls out what will it do to the engine if it’s ran? Mine has currently been lost, now I’m worried about running my machine.

@irishguy200007 Жыл бұрын

Do these have to be spunge quickly in order to get them to prime?

@nikutb6798 6 ай бұрын

how will we check the rotor and camshaft?

@robhummel4379 5 жыл бұрын

nice fidget grab

@killerbanjo Жыл бұрын

Hey mate, do you know the thread and pitch of the bolts at 05:26?

@robertmintz63 4 жыл бұрын

In your assembly at time 1:47- 1:57 what is that part you are saying must hang over just a touch, ? l have not taken my pump apart , l have only turned the fuel plate, with the pump still on the tractor ! Since I don’t know exactly how it is supposed to be , l would not know if what l saw was correct or wrong !!

@thomasschwaemmle6943 2 жыл бұрын

Its posible more fuel setting at 3 cylinder mwm engine?

@geraldsanford2411 7 жыл бұрын

i have a serious dilema am working on a 1996 FORD F150 4.9 L6 need a picture of the bottom of the underhood fuse box showing pin placement and wire coloring about half the wires in my fuseblock literally fell out the bottom of the fuseblock can anyone please help me and thanks the fusebox is numbered 1 to 69 on thye bottom of the fusebox

@JimCoupeTQ Жыл бұрын

Hi! That small spring at the bottom that you talked about at the intake of fuel. You said it will be stuck in priming mode and it wont run. But isnt priming mode making it run as h*ll? Yester day i pushed down my primimg button on my DPA and the engine went crazy and ran away. I cant get it to stop normally anymore? Its like the pump is stuck in max fuel setting??

@briansmobile1 Жыл бұрын

What time stamp in the video? Priming mode is to purge air and flood the rotor with fuel.

@mikealdag7309 3 жыл бұрын

Great video , thank you

@robertmintz63 4 жыл бұрын

I watched this vid about 10 times before l got the fact that you were stating the min/max fuel setting correctly at the 30 sec point & the 45 sec point & l have used it to try and get some more power out of my 4BT Cummins 390 1990 . Some time ago l was having trouble ,& a tractor mech said it was my inj pump , he had a shop rebuild it , & when l got it back it was real short on power ! They jacked around fir 3 days and finally gave the pump full advance, but the power level still low !!, IT was a dirty in line fuel filter one of those little ones , 3/8 fuel line . YOUR vid has shown me how to add more fuel , but things still are not right , hardly no smoke , even at max fuel . How could they have messed up my pump???? I wish l knew how to get hold of you , l don’t want to give my e-mail address to the world. The part that you put on at 1:40 with the 2 -12point bolts , ? Is it possible to install it incorrectly??

@xxturbowesxx 4 жыл бұрын

I have this injector pump on my Perkins Diesel in my boat and am dumbfounded how to adjust the governor max speed setting. Mine has a hydraulic governor and I can't find anything. The mechanical one is well documented but I've reached a dead end.

@dean-gm1lg 3 жыл бұрын

There's useuely a pressure sensitive valve that dumps fuel pump body fuel pressure which in turn alters the fuel pumping element /s load setting

@irishguy200007 Жыл бұрын

Is it ok to set it to maximium

@HorizonFarming 3 жыл бұрын

I just adjusted this fuelpump on my John Deere 2040. Now it is quicc and have some blacc smoke

@ketilmomrak-haugan3495 3 жыл бұрын

Was that a cav pump like this?

@HorizonFarming 3 жыл бұрын

@@ketilmomrak-haugan3495 Yes, yes it was

@ketilmomrak-haugan3495 3 жыл бұрын

@@HorizonFarming did you set it to max?

@HorizonFarming 3 жыл бұрын

@@ketilmomrak-haugan3495 Yeah, i set it to Max. But theres a lot of black smoke coming from it when i floor it. It's probably best to set it to max, and then adjust it off a little.

@ketilmomrak-haugan3495 3 жыл бұрын

@@HorizonFarming yeah OK, i want some black smoke so thats good😏😏

@bruceevennett4363 4 жыл бұрын

Does that increase hp if you change injectors?

@MF175mp 3 жыл бұрын

Not much unless the old are really gone

@lisa-anne5279 5 жыл бұрын

Lol "Angel like reflexes"

@robertmintz63 4 жыл бұрын

Well you did not let us know how you sky track works after you put it all back together

@robertmintz63 4 жыл бұрын

At 2:00 you use an impact ,, what is the specified torque of those -2- bolts , & how much torque does your impact give? What brand & size are you using?

@johnpike9612 2 жыл бұрын

Wheres part 3?

@briansmobile1 6 жыл бұрын

This is where I got all the parts for this pump rebuild → amzn.to/2rJhqmd

@webslinger2011 7 жыл бұрын

Parts are very expensive. Also, water destroys it as well. Had cases where it got very rusty.

@briansmobile1 7 жыл бұрын

The parts all included for this were $85, but water hadn't gotten to it too bad. Are you outside the US?

@webslinger2011 7 жыл бұрын

briansmobile1 Spent 2 1/2 years working in Australia. There's still an awful lot of stuff to learn on diesels but now I'm working on building electric motors.

@briansmobile1 7 жыл бұрын

I figured you might be. My parents are in New South Whales.

@webslinger2011 7 жыл бұрын

Almost had a job there. Chose to work in Darwin instead. Unfortunately it didn't work out. Workshop closed down after 2 years. Drove 10,000 kms from Darwin to Albany and then to Adelaide.