I'm going back and studying your old videos it's crazy to see your growth

Clever stuff , I had to give up bricklaying 15 years ago because of a bad motocross crash you’ve showed how thing have changed on sites 👍

Another super trowel.Used your pick and dip method on a splash back wall last year Charlie...obviously another great time served lad.Keep up the good work 👍

I'm Impressed with some of them clamps they look really good gonna have to purchase a few 👌

Good clamps especially the internal and top clamp, good hard hat Charlie you are definitely your own man👍

Thay look like good quality clamps love the video's man

Brilliant use of dolly’s,much easier than what l do,putting a packer top and bottom.l see the advantages,nice one

Looks good stuff.

Have you tried the Blake’s intermediates? We use them to tail the corner out from the corner profile. As on base lift or timber frame we wouldn’t be able to use the dean clamp. Wicked for roughing up the cut ups too, sack the the bolt that goes through the wall, just 2 tight f clamps keep them sterdy

That 05 clamp is bad boy

Nice video 👍 thanks 👍👌🍺

Charlie if you go on eBay and type 4x external Line holder clips for profile they should come up for 50mm profile.. I had a few that were too tight for the clip the slide up and down but these worked out for me . They was about 8quid

Nice work charlie👍

Dori block next investment charlie! Great videos keep them coming son!

nice clip again charlie boy love the boofont too lol

Where did u get the clamp from ,the adjustable one off the blockwork to the profile in middle of the wall cheers

Just used your discount code - cheers.

Right what size thickness are your profiles? they seem really light!

Them clamps are the asboulte bollocks 👍 Deff 100% the way forward

I live in Perth WA, good to see some good Brickie’s. Not very good here.

What are your thoughts on the other style of profile that sits out from the corner are they more of a pain to set up , never used profiles before was thinking about buying a set

What brick line you use ? I’ve been using cardoc but keep looking at that W.rose line

Where you get those clamps Charlie mate ??

So basically bt clamps are the bollocks and all you need is some hollow section for your profiles?

Are the Blake’s internal external profiles worth looking at

Watched a fair bit of your work geez you’re a good bricky where you located?

Never see 4 inch block with a brick/ect veneer over here, it is a shame they don't make the top clamps smaller so you can hook on the slab side of an 8. Plus it is like pulling teeth to get labors to set you up (up above) to reach as near too the top of the poles. Climbing braces, standing on stocked brick, stocked back hops in the way, holding a level flat against the wall and reading your distance your pole is from the wall and adjusting the clamps is a 3 handed job but only have 2. We always use the foots and the company has home made L-brackets (screw to studs or hammer drill /tap con)that you can adjust using someone's rusty crescent wrench and a rusty bolt and a hammer to wack it in and out, well maybe need 4 hands.

When you put up these profiles tigt to the bottom course and then put your line on. It off sets the brickwork by the thickness of the line Why not to put a small packer at the bottom of the profile

Do you boys use radios to communicate or is it me goin nuts ,of so that's quality

A magnet level also saves heaps of time plumbing up

When pulling two ways off a profile I use the dori blocks you got to try them there so good

Monday morning send me another video on KZfaq of yourself builders yes I am🤪🤪🤪

you can use a dorri block, which slides on youe poles, to take your line, lot better than corner blocks, you can get them from ses brickies tools,

The 'Nipple-Clamp-Champ' Strikes Again😅

or you could just learn how to build a corner without profiles, through them away and make more money.

Too much pissing about by far two decent trowels wack corners up job done