1965 C10 Chop/Drop & LS Swap - Part #5 - Wiring, Exhaust, Driveshaft, etc / 65 C10 Makeover

Рет қаралды 16,511

Жыл бұрын

Website: www.brotherstrucks.com/
In Part Five/Week Five of our 8 week transformation series on our '65 C10, we're laying down the infrastructure that will get our 5.3 LS ready to run. This week we build our Flowmaster Exhaust, wire our engine with our Holley Terminator Max and get our driveshaft sized up among other things. Dave Welch is a classic truck Specialist and he's got plenty of tricks for nearly every project on your classic Chevrolet or GMC Pickup! Find Dave's videos and more for your classic truck at www.brotherstrucks.com
Connect with us:
Instagram: / brotherstrucks
Facebook: / brotherstrucks
Twitter: / brotherstrucks

Пікірлер: 31

@vorhese Жыл бұрын

Baby, what DOESN't take longer than expected?

@deankay4434 Жыл бұрын

Everything when it's custom! ASE Master Tech since 78.

@nunnf-off407 Жыл бұрын

Motor, front end ,

@robertlambert5299 Жыл бұрын

Dave’s got cool hair. I wish I had Dave’s hair. Looking good Dave and the guys!

@ix_d3monzz_xi135 Жыл бұрын

uncle dave the goat

@deankay4434 Жыл бұрын

Dave, thanks the mention of grounds & dielectric grease. The GM ground terminals in the 80's came with little twisted spike to dig in past paint, grease etc. I keep a large pile of 4 sizes of "Star" washers on hand. Maybe my OCD, but I double ground all lights, modules, doors to body, even the end frame of the alt where negative diodes produce ground. Plus pickups uniquely have a bed that a ground with good service access as inside LED's are popular. Great job & your team!

@BROTHERSTruckPartsTV Жыл бұрын

Bad grounds are the root of almost all the electrical problems we run into.

@deankay4434 Жыл бұрын

@@BROTHERSTruckPartsTV On the old truck tail lights, I clean and solder the bulb socket to the housing because it is just pinched-stamped. 50+ years take its toll and seen as a voltage drop test.

@AaIsForAaliyas Жыл бұрын

Absolutely beautiful

@BROTHERSTruckPartsTV Жыл бұрын

Thanks!

@oldblueshhrchannel1847 Жыл бұрын

Beautiful and entertaining! Thanks David and crew!

@BROTHERSTruckPartsTV Жыл бұрын

Our pleasure Oldblue!

@outragousbob4367 Жыл бұрын

I love this series! Dave and crew bravo!!!

@BROTHERSTruckPartsTV Жыл бұрын

Right on!

@JenzRock Жыл бұрын

Digging this series.

@BROTHERSTruckPartsTV Жыл бұрын

Right on! Thanks for watching.

@lazyhoundracing9621 Жыл бұрын

looking good.

@mikelove9832 Жыл бұрын

Thanks Straight Ahead ✌😎

@DadbrosGarage Жыл бұрын

The sound of the hood being shut haha. Sounded like a bomb

@BlueMacGyver Жыл бұрын

I love this stuff, good content! Dave is the best

@BROTHERSTruckPartsTV Жыл бұрын

Thanks for watching!

@CAROLDDISCOVER-FINDER2525 Жыл бұрын

Next time when you build one of these build a; lexan hood, cab floor lexan, and A lexan Floor on your bed. Make it clear so everybody can see all the beautiful work you've done below. Okay only maybe 10% serious on that about the lexan. But the work is fantastic finish and fit and seen in the video. 100 extra bonus points about mentioning the magnet in the gas tank. Which isn't really fair because you made some other great points I should be mentioning also, I saw it back brace and you did not look to be in near as much pain. That's a great thing hopefully that becomes a norm less pain for you. But I know it can vary from day to day and sometime even minute to minute. The change in weather especially temperature but don't forget the barometric pressure please have it when it changes as well. Back in the day you could have sold posters of your build just what you have already done even. Look forward to next episode.

@BROTHERSTruckPartsTV Жыл бұрын

Man you are really paying attention to those details! Thanks again for watching and for the comments, see ya next week.

@CAROLDDISCOVER-FINDER2525 Жыл бұрын

@@BROTHERSTruckPartsTV Thanks, trucks always love trucks. Although 67 to 72s my favorite era of Chevy trucks I like the 60 to 66 a lot too. Nice build.

@thabigghomie_ Жыл бұрын

💪🏾❤️

@tonierichmond5302 8 ай бұрын

How do you budget template plate to cut a chassis?

@PeterHatch-mx7zc 11 ай бұрын

Whats the fuel tank

@BigJim_909 Жыл бұрын

Awesome work, but…. What happened to the custom driveshaft crossmember you guys sell? Wouldn’t that make sense for the exhaust?

@BROTHERSTruckPartsTV Жыл бұрын

Yeah, or the cutouts we sell would be an option too, but we simply didn't have time to do anything extra and the bits we had worked anyway after we flipped and flopped them around a little.

@BigJim_909 Жыл бұрын

Great project. I love it! 💪🏽