2011 and up Grand Cherokee WK2 ROugh Country leveling kit install EXTREMELY DETAILED

No video

2011 and up Grand Cherokee WK2 ROugh Country leveling kit install EXTREMELY DETAILED

Рет қаралды 26,724

Күн бұрын

Level your jeep with this How to Video!!!!
Drop a comment below if you have any questions and dont forget to like, SUBSCRIBE and share with your frineds!!!!

Пікірлер: 56

@shawn1625 10 ай бұрын

Just did this job... My suggestion is to not reuse the locking nuts that are used in the upper control arm and tie rod. My other suggestion is to make sure you have a ball joint separator because you can only beat on your car so much before you accidently break things. If I would have had these things available it would have been much easier.

@mkedan6741 3 жыл бұрын

I have a 19 JGC and have this kit which I plan to do this spring. The locktite is a good idea but I would also remove the rotor(it's held on by a o-ring). The insructions show removing the knuckle. Every video I have seen of this is different but yours is helpfull. Thanks.

@BSBASSIN 3 жыл бұрын

I do these on a weekly basis what I say will work trust me.

@mkedan6741 3 жыл бұрын

@@BSBASSIN I just pulled the wheel off and what I thought was plating is aluminium. The 2019's have a alloy lower control arm and knuckle. No hammering! I have to figure out how to get the tierod and upper balljoint out without damage. Mine is a Hemi powered Limited with the tow package/Nivomat shocks, the ass end is exactly 2 inches higher than the front (measured @ wheelwells) and I want it leveled. Thanks again for the video and any advice is always greatly appreciated.

@scotianbank 9 ай бұрын

Awesome guide!! I hate to be a nuisance, but could you write up a list of all tools you'll need (maybe a "must-haves" list, and a "nice-to-haves" list?) to install this kit? Thanks!!!

@Izzydominguez22 3 жыл бұрын

Keep up the good work my friend. This video put all the other install videos to shame. You are appreciated.

@BSBASSIN 3 жыл бұрын

Thank you sir! I try to do my best to help others

@johngaringalao9143 2 жыл бұрын

Thank you for this very detailed video!

@adamkingersoll5185 4 ай бұрын

Excellent video. I did this on my 2017 dodge durango gt. This kicked my butt. I had to take the sway bar off because it was interfering with the tie rods. Any ideas what I can do for a sway bar?

@sheerwillsurvival2064 2 жыл бұрын

Everything rust in the rust belt not much rust on my Jeep’s in Texas 😁

@cmorgan0909 3 жыл бұрын

Great work man. If you don’t mind me asking, what did you charge to do this? I’m considering DIY versus paying a shop. Or, any shot you’re in Chicago area? I’d gladly go to you

@BSBASSIN 3 жыл бұрын

I am in Chicago. Find me on fb Brian Risley and send me a PM. It's a picture of me holding up a fish.

@BSBASSIN 3 жыл бұрын

Or tell me how I can get in touch with you.

@loboa2747 2 жыл бұрын

Brother I’m in Chicago as well struts on their way from florida, can we some how talk to see how much you you’ll charge me to do both

@durteeduce3849 Жыл бұрын

Im currently looking for a shop or someone to take my Jeep too in chicago as well if yall have any recommendations!

@CombatLazza 3 жыл бұрын

Great video, thank you mate

@s2knott 3 жыл бұрын

excellent video!

@adamt4742 Жыл бұрын

would this be similar or pretty much the same as a '12 Durango?

@BSBASSIN Жыл бұрын

Probably the jeep and dodge are the same platform. I have not done a Durango recent enough to remember though.

@jackstracks4794 3 жыл бұрын

Thanks for the detailed video. I'm thinking of doing this on my 2020 JGC. I was told that I would have to do a front wheel alignment after the install, do you agree?

@BSBASSIN 3 жыл бұрын

Yes

@hellkitty1014 3 жыл бұрын

HIGHLY recommend an alignment with so many components removed.

@camaroboi13 3 жыл бұрын

Nothing like pulling everything apart only to find that on 2017 the strut bolt is well over 1” and I don’t have that size

@michaelhorn4540 2 жыл бұрын

Im ordering a RC 2.5 inch lift kit for my 2011 grand next week

@BSBASSIN 2 жыл бұрын

Awesome you will love it

@alejandroandrade2016 2 жыл бұрын

Muchas gracias por tus detalles 👌

@matthewskowronek4116 3 жыл бұрын

Would have been nice to see the final outcome

@BSBASSIN 3 жыл бұрын

Search bs bassin on Facebook and message me I'll get you phoots

@camaroboi13 3 жыл бұрын

@@BSBASSIN I don’t have social media

@alanalvarez400 2 жыл бұрын

I have a 2013 grand cherokee I put the leveling kit rc 2.5 in front but my shock absorbers have already decomposed, DO you think that i need to buy longer ones or with the originals it should me ok.?

@BSBASSIN 2 жыл бұрын

Just buy quality ones. Shocks are rated for 50k miles

@maazmohammed9021 3 жыл бұрын

Hlo,can I put this lift on 2011 jeep grand cherokee laredo???

@loboa2747 2 жыл бұрын

I have someone else installed the leveling kit for me so now I want to replace the struts, do I have to do the trimming of the bolts like you did? Thank you in advance

@BSBASSIN 2 жыл бұрын

Not sure if it's installed everything should go in and out easily

@nissanquest2002 2 жыл бұрын

Are the motor mounts accessible when replacing both struts ? Thank you .

@BSBASSIN 2 жыл бұрын

I don't remember

@ballsbuster12 3 жыл бұрын

does the jeep your working have air suspension or regular coils suspensions?

@MonkeyDLuffy-cm9bc 3 жыл бұрын

You can't lift the jeeps with air suspension only coils

@ThatRacingBanana 11 ай бұрын

Im converting mine from air suspension to a strutmaster coilover system with the rough country lift kit

@carnage6288 3 жыл бұрын

I put on the RC 2.5" kit on my 2018 GC w/stock 18" wheels. Do you happen to remember what his tire size was he put on? Looks like he has 20" wheels. Thx

@BSBASSIN 3 жыл бұрын

I actually do not I know they barely fit when it was stock

@hellkitty1014 3 жыл бұрын

You could get away with 285/60s. Anything wider or taller and you will have to trim/push the pinch weld back.

@outdoorreelz3181 2 жыл бұрын

Did you cut the bolts so you didn’t have to compress the springs?

@BSBASSIN 2 жыл бұрын

Not the bolts have to be cut because they are too long for the spacer that mounts on top of them.

@outdoorreelz3181 2 жыл бұрын

@@BSBASSIN ok. Everyone else I’ve watched as had to compress the springs to get the spacer in. Did you do that? Thanks

@bobelkiniii1461 3 ай бұрын

Why pull the CV

@allstarfailure6848 3 жыл бұрын

so do you have to have it realigned after this?

@BSBASSIN 3 жыл бұрын

Yes

@lucystephenson1371 10 ай бұрын

Whomp whomp

@ballsbuster12 3 жыл бұрын

where are you located can i bring my truck to you ???

@BSBASSIN 3 жыл бұрын

Chicago area. Find me on Facebook Brian Risley

@wilder211 Жыл бұрын

I thought compression of the springs was required?

@BSBASSIN Жыл бұрын

Not with this kiy

@wilder211 Жыл бұрын

So you do not have to remove the lower ball joint nut? The instructions says to remove.

@BSBASSIN Жыл бұрын

@98th Meridian please watch video everything is in the video. I install leveling kits o. So many different suv, trucks, and even subaru cars I cannot remember everything from every one