GYPFOR website ▶︎ www.gypfor.com
🔥 How to MAKE a PLADUR Wall with 70mm Profiles 👉 • 🔥 Cómo HACER una Pared...
In this video you will see how to mount a curved plasterboard wall.
We will use 70mm angle and studs. We will place two layers of Gypfor brand plasterboard. In the first layer we will use a 6mm thick plate and in the second layer we will use a 10mm thick one.
The plates with these thicknesses are manufactured to be able to do this type of work.
✅ If you are going to do some PLADUR work, and you are going to choose to hire a company that does it, I have created a brief guide to help you analyze the budget and avoid common deceptions in the sector.
Go to www.tutorialcreativo.com/guia to download it.
🟢 Drill 👉 www.banggood.com/custlink/3Km...
🔵 Page 👉 www.banggood.com/custlink/KDG...
🔴Sander 👉 ▶︎ amzn.to/3fRPTLc
Video transcript:
Very good!
Today we go with this curved wall.
We place a piece of plasterboard on the floor, to be able to fix a screw and thus mark the curve.
We mark the line on the wall.
We mark the center of the hole, which will be the radius of the semicircle.
We fix a screw just where the two lines intersect.
We take a string to mark the semicircle and hook one end on the screw.
We hold the pencil at the other end and mark.
Now we mark 7cm from the line and do the same as before.
We pass the reference point to the upper slab.
Drill at the point and place a plug.
In this case we will use another idea to mark the semicircle.
In a piece of profile we make a hole at one end.
Then we mark from the hole the radius of the semicircle and from there 7cm more.
We hold the profile with a screw.
We put the tip of the pencil in the hole and mark.
We change for the other brand of the profile and we mark.
In this case, we will fix some angles in the semicircle. We make some cuts on one side of the angle every 5cm, more or less, to be able to adapt it to the curve.
We also have a channel for curves, which would make our work a little easier. But in this case I will show you only with an angle.
We make some marks every 30cm to fix the angle. That's where the studs will go. We make sure that when marking, the meter makes the same curve as the line, so that later the uprights coincide well with the plasterboard plate.
We drill in the marks and fix it with plastic plugs with screws.
We do the same in the other brand.
Now we repeat the process on the upper slab.
You can use the leftover pieces of angle.
We measure and cut the uprights, placing them at each mark.
We fix the uprights to the channel, the axis of the upright in line with the mark we made.
We put a well plumb upright and fix it at the top. Then we use it as a reference to fix the other studs.
We mark the lead where the curved wall ends.
We measure the height to cut the plasterboard, you always have to count it so that it is suspended from the ground about 15mm.
We will place two layers of Gypfor brand plasterboard. In the first layer we will use a 6mm thick plate and in the second layer we will use a 10mm thick one.
The plates with these thicknesses are manufactured to be able to do this type of work.
We put the plate in the correct position and flex it a little, before placing it. It can be moistened a little at the back to make it curve better.
We put the plate and fix it with a screw in the center.
Now we go to the top. We adjust the plate well so that the side of the plate is in line with the axis of the upright and screw.
We screw into the central profile and then go to the sides.
We measure and cut the side plates.
We put them on and screw them on.
We go with the 10mm plate.
We flex the plate. We place it so that the joint does not coincide with the joint of the first layer.
We place the laser so that it coincides well in the center of the stud.
We screw the plate in line with the laser and then we screw profile by profile.
We measured the plate to the line we made.
We cut with the saw from the side so that the plate is well against the straight wall.
We go to the other side of the wall and put the insulation.
Now we do the same: we will place two layers of plasterboard.
We have to take into account that now we have to bend it on the other side.