Build the Ultimate Micro Racing Drone for $120 in 2024

No video

Build the Ultimate Micro Racing Drone for $120 in 2024

Рет қаралды 15,452

6 ай бұрын

Parts for the micro drone will be listed below!
Hope this was helpful to someone because this style video takes a while to put together. I am planning on making a video including the binding and setting up the drone so if your needing that, be on the look out!
Thanks for watching, let me know if you have any questions even if you think it might be a dumb question, we all start somewhere so let’s here them.
Flight Controller: newbeedrone.com/collections/a...
Motors: newbeedrone.com/collections/n...
Camera: newbeedrone.com/collections/a...
Frame: newbeedrone.com/collections/a...
Camera mount: newbeedrone.com/collections/a...
Propellers: newbeedrone.com/products/colo...
Batteries: newbeedrone.com/products/nitr...
SHOUT OUT to my Sponsors:
newbeedrone.com ALL TINY WHOOP products and for making this video possible!
www.ampow.com and newbeedrone.com LIPO's
www.foxeer.com and newbeedrone.com FPV CAMERA's
www.gemfanhobby.com and dalprop.com PROP's
shop.iflight-rc.com and newbeedrone.com MOTOR's

Пікірлер: 73

@The2xWhiskey 6 ай бұрын

5:30 Cleaning the area with alcohol first helps too. There may have been a film of oil or other residue from the manufacturing process.

@wynnfpv 6 ай бұрын

Yes, great recommendation! Thanks

@johnhanley9946 5 ай бұрын

It's most likely from when the grommets were installed...

@kaskalo2 6 ай бұрын

The only thing missing is to show how it actually flies 😊

@wynnfpv 6 ай бұрын

I’ll have that up soon! Thanks for watching👊🏼

@kaskalo2 6 ай бұрын

@@wynnfpv looking forward to it. Cheers mate!

@PinkeySuavo 3 ай бұрын

Also, is there some tuning/programming involved? Is flight controlled pre programmed? Or do we need to set up something, PID tuning and so on? I never built my own drone.

@Dunkelstrasse 2 ай бұрын

@@PinkeySuavo In my experience the setup process is especially difficult for these tiny drones. Betaflight stock settings are optimized for 5 inch quads, so it will probably fly, but tuning it would be advisable. But in general, if you build a drone like this yourself, you will have to programm a lot of things in Betaflight... Seting up the control link, video settings and channel, sometimes you have to configure the ports so that the different parts communicate correctly with each other. Depending on how deep you wanna go with it and what hardware you choose to build your drone out of, it can get really complicated. But the FPV community is pretty open, you will always find advice somewhere online.

@ALWA7SHSEX 18 күн бұрын

Mb its not flying lol

@georgew.9663 6 ай бұрын

You know about the floss trick to get the grommets in? You fold some dental floss over itself to get a little loop, feed it through the hole, and loop it around the grommet and pull it through

@wynnfpv 6 ай бұрын

🤯 no I never heard of it… I’m behind times I guess… lol I’ll try it!! Thanks man!

@hartleyaerial 6 ай бұрын

Nice simple build, Wynn. Looking forward to seeing how it flies!

@wynnfpv 6 ай бұрын

Thanks! I’ll be posting it soon!!

@warbuli 5 ай бұрын

Would be nice to have a small section at the end showcasing the drone flying and giving some feedback on pros and cons!

@wynnfpv 5 ай бұрын

I’ll post another video of flying! Thanks for the suggestion👊🏼

@coimbrafpv 18 күн бұрын

Good work, congratulations.

@wynnfpv 18 күн бұрын

Thanks to you

@robertnastasi4738 4 ай бұрын

Flux should always be used. It not only allows the solder flow properly it also cleans as well. I recommend a NO CLEAN flux. Then I clean of the AIO with 90% rubbing alcohol. Always flux always. keep flying great build video, Thanks

@wynnfpv 4 ай бұрын

Thanks for your good insight. 👊🏼 Thanks to watching also!

@hoagietime1 5 ай бұрын

I broke that canopy first crash. I really wish they printed it out of TPU like the tinywhoop ones that fit the pinch cameras. I love the design, works perfect for the walksnail whoop cam, just extremely fragile

@wynnfpv 5 ай бұрын

Man… I’m sorry to hear that…

@jonask.1409 6 ай бұрын

You can get these rubber grommets in to the holes of the FC with some dental floss. Just put it arount the grommets, put the dental floss through the holes and pull it through

@wynnfpv 6 ай бұрын

I learned that recently haha. I guess I was behind times😂 never learned the new trick😂

@Fayzooooo 6 ай бұрын

You literally built the hummingbird that they already sell for $89

@wynnfpv 6 ай бұрын

While the BNF is a good option this one would be better for less weight and being a lot quicker. The motors in the BNF Hummingbird are 0802 25,000kv and on this build I used 0702 29,000kv. Also the frame and tpu cam mount save around 3 grams

@wynnfpv 6 ай бұрын

My hummingbird BNF came in at 21.84grams and this build is 18.35

@Fayzooooo 6 ай бұрын

@@wynnfpv i guess it’s not bad for the price

@KOrnhOliO1 5 ай бұрын

@@Fayzooooo3.5 grams weight savings is huge!

@John_Doe_6996 4 ай бұрын

Pro tip, Flux is your friend! Use it on every joint, every time, it makes a HUGE difference. If its not smokin, you need more flux.

@wynnfpv 2 ай бұрын

Thanks for the tip 👊🏼

@blindsquirrelRockChucker 6 ай бұрын

I wonder if the weight of the 12 60/40 soldier blobs is less than .31grams🤔 of the connectors?

@wynnfpv 6 ай бұрын

Haha true😂😂

@pauls5745 5 ай бұрын

yeah, you probably only net .2g, but the FC is solder connected and lighter than cutting motor connectors than add connectors to the FC. not great weight savings, but avoiding weight gain.

@Drexfpv03 6 ай бұрын

Cool Video, Im looking at getting one soon, Can You do this but a 75mm??

@schweizerluchs7146 6 ай бұрын

you can easily take the same parts and just use a 75mm frame. Maybe you want to go with a 0802 Motor, but otherwise its fine.

@Drexfpv03 6 ай бұрын

@@schweizerluchs7146 aaah yea I guess that is true

@wynnfpv 6 ай бұрын

Yes, you’d want to change the motors like schweizerluchs said.

@kekwkekw5117 4 ай бұрын

Different soldering tips would help you. Look into soldering more. You’ll be surprised how deep it goes. Seems simple enough to most.

@wynnfpv 4 ай бұрын

I’ve had the same soldering tip on there for ages lol. I have others just don’t take the time to switch them out😂 thanks for the suggestion 👍🏼👊🏼

@hookedfpv3219 Ай бұрын

You need to try the tinywhoop pinch camera

@wynnfpv Ай бұрын

I do!

@chrishallock8596 5 ай бұрын

Seems like this video was sponsored by new bee drone 😂

@wynnfpv 5 ай бұрын

Yes, NewBeeDrone helped and sponsored the video. Also BetaFPV sponsored and helped with my other whoop build video. I don’t receive cash from any brand but I do receive parts to help with build videos and content. Thanks for watching

@wincydelavega653 4 ай бұрын

I got my 85mm drone and radio master pocket for 134 dollars 😀

@wynnfpv 4 ай бұрын

Sweet!! There are great budget options!!

@AsphaltShredder 5 ай бұрын

Use fross for the grummets and it's easier

@wynnfpv 5 ай бұрын

I recently learned this trick haha. I was behind times😂

@joaomarveloso1049 5 ай бұрын

Thank you for the video. Do you knoe if there is a tiny fpv drone with really good 4k video?

@wynnfpv 5 ай бұрын

Yes, there actually is. It is a little bigger than the one I made in this video. I’ll put a link here: newbeedrone.com/products/acrobee75-hd-o3

@joaomarveloso1049 5 ай бұрын

@@wynnfpv Thank you 🙂

@SimonMicrochip 29 күн бұрын

Frame link is dead in the description

@wynnfpv 22 күн бұрын

Interesting. Thanks for sharing… I don’t know why it’s not working

@grox3857 6 ай бұрын

Very good build video, I love how good quality videos you can make. Maybe I would try Betafpv Cross F4 Serial elrs, plus SEPARATE OVX300 VTX combo with 300mw max vtx output and easily repairable. Top tier pilots like T Dog are flying on this setup and I switched also, Its very good and ROBUST. You can check how it flies on my channel also will do DIY Tutorial how to build it soon ;) Cross AIO plus OVX300 with wire antenna inside meteor 65air frame weight approx 17.8G with Props and better BT2.0 Power wire

@wynnfpv 6 ай бұрын

Thanks I appreciate it! I’ll check out your channel!! I have one BetaFPV build which I did a while ago. I’d just switch up the motor and camera mount now. I like that build a lot and it flies great!!

@gunjafpv 4 ай бұрын

no wonder had issues tinning, black soldering iron tip!! Clean tip (unless you a dirty girl!) haha. Nice info though!

@xBarnabyJonesx 6 ай бұрын

Eh, was very disappointed to see a NewBeeDrone build. I came here looking to replace my Hummingbird, its been an absolute nightmare. Ive had 2 Hummingbird V4 FCs and 2 Bee Eye cameras die, in pretty light crashes. Bee Eye camera is a car reverse camera and if you tap it wrong you get reverse lines. Plus, all of the issues with the "special" OSD chip. Mine never worked right on 2 different FC's, the OSD cuts out and flickers randomly. The motors are great but NBD uses "special" connectors, which makes it a pain to swap with anything else. Seems NBD wanna be the Apple of drones but they missed the boat. Proprietary parts don't work well with hobbyist. Feel like NBD could be great if they would get out of their own way.

@wynnfpv 6 ай бұрын

I’m sorry to hear you had a bad experience with NBD parts. If you looking for a different branded build. About year ago I made a similar video with betafpv parts: kzfaq.info/get/bejne/ZrFderemrK-acX0.htmlsi=7Xm0cPyn9_pCHsWy If your going to build similar to the BetaFPV build I would switch out the canopy to something lighter and motors 0702 and higher kv.