Building a Monster 500WHP 4G63T (Extremely Satisfying)

Рет қаралды 90,320

Күн бұрын

Today we rebuild the 4G63T and turn it into a monster, 500whp capable motor for the mid-engine Eclipse! #4g63 #dsm #satisfying
SONIC TOOLS ► sonictoolsusa.com/
MID-ENGINE ECLIPSE GIVEAWAY ► lp.powerjdm.com/gingium
SUPPORT ME HERE! ► / gingium
SHOP REAL CARBON FIBER ACCESSORIES! ► www.simplycarbonfiber.com/Gin... (Use GG10 for 10% OFF)
00:00 Intro
00:51 Bottom End Re-Seal
05:30 Head Install
08:00 Oil Pan Baby!
09:52 Sonic Tools FTW
11:00 AN Conversion
13:27 Turbo Time
17:51 New Clutch & Flywheel!
21:40 Engine Install
OTHER VIDS!!
Quick Builds► • Quick Builds
Drift Truck ► • Drift Truck
Rally Miata ► • Project Rally Miata
Eclipse ► • 1G Eclipse
LS Volvo ► • Volvo Sleeper
BE MY FRIEND!!!!
Follow me on Twitter ► / _gingium_
Follow me on Instagram ► / gingium
MY RECORDING EQUIPMENT!!
Camera ► amzn.to/3lVq7J9
Lens ► amzn.to/3yhf168
Microphone ► amzn.to/3q4pv5x
Tripod ► amzn.to/3pOGiZR
Carry Bag ► amzn.to/3rV50uz
SD Card ► amzn.to/3lQdv68
MY FABRICATION/MECHANIC EQUIPMENT!!
Welders & Supplies ► www.usaweld.com/?Click=67190 (code: GINGIUM)
CNC Plasma Table ► store.langmuirsystems.com?aff=23 (code: GINGIUM)
Tube Bender ► www.roguefab.com/ (code: gingium25)

Пікірлер: 295

@JamieBainbridge 2 жыл бұрын

To solve the dipstick problem, just install the engine the other way around. Then you'll have an Eclipse with multiple reverse gears like the opening scene of the first Fast and Furious movie. Authentic! 😎👍

@redsquirrelftw 2 жыл бұрын

And R means "race mode". It goes forward!

@JLKING98 2 жыл бұрын

Isnt this possible to correct by "inverting" the diff somehow?

@ricardobarrios4159 2 жыл бұрын

That car actually had a tractor gear box between the normal trans and the diff.

@wrexz 2 жыл бұрын

They also had a 15 speed gearbox and 20 mile runway in the one where they had to stop that cargo plane before the bad guys escaped

@TheOnlyKontrol 2 жыл бұрын

@@wrexz you act like no one saw that and cringed

@Dantifrice 2 жыл бұрын

can we appreciate that 3 sponsors has been made in this video and NONE of them was boring or useless?

@_Gingium_ 2 жыл бұрын

Really more like 4! LOL

@makeitorleaveit1 2 жыл бұрын

Yes my thoughts exactly Gingium keeps it real even through the hard times that's why he's one of the best for sure

@SeanHodgins 2 жыл бұрын

You should get a couple of cheap dishwashers for the shop to run parts through.

@Simpyspec 2 жыл бұрын

Does that actually work?? just use degreaser instead of water would be badass!

@SeanHodgins 2 жыл бұрын

@@Simpyspec yep! they work really well, just need one with a built in heating element. And you could probably hook it up to a basin as a way to reuse the degreaser solution.

@alfonsorodriguez9055 2 жыл бұрын

Having a sponsor and mentioning them and using the tools from the sponsors has been a great trade off. Seeing how much more organized you are now is great. The quality of videos are A+ keep up the good work man.

@ichdu4104 2 жыл бұрын

Dude this is the most serious of your builds so far and i'm loving every second of it. It's great to see you improve with every video and every challenge. The whole struggle from last year was worth it when I see you out doing even bigger car channels here on KZfaq. Keep it up man you're killing it!!

@X-Caliber02 2 жыл бұрын

Not disagreeing that this is a very serious build, because it is... But (and this is just my opinion), I think the Off-road, AWD, EJ Powered, Miata just slightly edges this out in seriousness (obviously this had the rear suspension engineered, but the Miata was AWD swap, both builds very close in the work though)

@tmlmagee 2 жыл бұрын

you really outdoing yourself upping the quality!

@marvinvisser5039 2 жыл бұрын

Agreed

@_Gingium_ 2 жыл бұрын

Glad ya'll noticed and enjoyed!

@pattyboi 2 жыл бұрын

New video guy putting in work eh? So much more movement in the shots, looks great

@boydb1212 2 жыл бұрын

Man, this is so good. Even ur removable xbrase is inline with the window cutouts. Makes me want to do better on my builds. Thanks for the inspiration

@ImInLoveWithBulla 2 жыл бұрын

Was I going nuts, or were you removing gaskets with what appeared to be a razor blade held with pliers? If so, you are the first mechanic in history to buy a CNC plasma table before you buy gasket scrapers. Your congratulatory cookie will be in the mail.

@_Gingium_ 2 жыл бұрын

😂😂😂😂 yes that is exactly what I was doing

@kylemcweeny878 2 жыл бұрын

@@_Gingium_ i saw that and said "that looks like a really good way to do that! Ima have to try it next time!"

@mattex3396 2 жыл бұрын

this comment section is so wholesome, almost all positive comments, we simply love seeing the quality your videos reached. Keep it up man

@JMRRebuilders 2 жыл бұрын

So excited to sit back and watch some great content on my Sunday. This is interesting watching you being filmed and not filming it yourself.

@gaydes1012 2 жыл бұрын

this thing is gonna be perfect for driving down the old town road now that the horses are in the back

@bigkeg9173 2 жыл бұрын

Your confidence level to tackle this build has grown so much over the last few years and you should be proud of yourself 👍

@802Garage 2 жыл бұрын

Dang that sucks about the bellhousing! At least it wasn't an AWD bellhousing. Woulda been an even more expensive oops. Really looking awesome in the engine bay.

@HailAzeez 2 жыл бұрын

It's great to see you using almost every equipment in the shop in this video!

@Fhwgads11 2 жыл бұрын

Have you considered making a little painting station for the shop? Nothing car sized but something for painting parts like valve covers and whatnot. You can just use a box fan with a filter element on the front and an hvac tube routed out the door if you wanted it to be able to move about. just needs to be a box with one side opena and a little turntable in the middle, then you can paint without it having to be nice out

@brandonmiller9155 2 жыл бұрын

Congrats on making your car harder to work on. Sincerely, an MR2 owner

@Glennquagmire1912 2 жыл бұрын

its so sick already, cant wait to see what it looks like with all the suspension in! rip bell housing tho

@_Gingium_ 2 жыл бұрын

I'll get ya a hint. It looks AWESOME with the suspension :)

@Glennquagmire1912 2 жыл бұрын

@@_Gingium_ just got the Patreon notification, cant wait💪🏼

@Blue__244 2 жыл бұрын

@@_Gingium_ do you have any plans for the volvo 240 other than the clutch and flywheel?

@xaviersavard8339 2 жыл бұрын

mf how your comment is 7 days old

@Blue__244 2 жыл бұрын

@@xaviersavard8339 Hes a patreon member or Something that alles hin to watch it earlier

@Paperhatchett 2 жыл бұрын

Dude this is your greatest and most serious build yet, I don’t know why you decided to give it away before it’s even done. You’re gonna miss it.

@austinconstant7681 2 жыл бұрын

Someone needs to sponsor you a parts washer.

@AndrewB416 2 жыл бұрын

This brings back memories of putting a 6 bolt 4G63 that I built in my basement into my 95 AWD TSi. Good times. Hard to believe that it was almost 15 years ago now.

@aimless-drifter 2 жыл бұрын

20:10 this is what I like about youtube. Videos like show that not everything always goes as planned. While working on one thing, another thing can break.

@josephdibenedetto23 2 жыл бұрын

You should add a fluidampr to the engine it helps the engine run smoother when running more boost and higher rpms. But damn this build is looking really good keep it up man.

@connorpigeon8108 2 жыл бұрын

Agreed blew my stock one apart

@IdEk5627 2 жыл бұрын

For the bell housing u should pre heat the area ur gonna weld as well as drill a hole at the end fo the crack and grind a groove in the crack. The preheat will help get some of the shit out of the metal as well as will help get full penetration.

@brandonmiller9155 2 жыл бұрын

That panning Timelapse was 🔥🔥🔥

@TheMarcin58CZ 2 жыл бұрын

Love this camera work, keep it up !

@mattreardon5648 2 жыл бұрын

Idk if you knew this... But do not I repeat do not use the throwout bearing that comes in any aftermarket clutch kit. Only use OEM throwout bearings on 4g63's

@Zaaf2003 2 жыл бұрын

Loving the camera guy.

@SuperRisingdeath 2 жыл бұрын

The only KZfaqr I don't skip sponsors on

@TomAlderman1978 2 жыл бұрын

The Timelapse shots are beautiful. Nice work!

@ragegamingvideosify 2 жыл бұрын

Just as I’m taking a break from my barra Z lol, thank you

@AtomicGarage 2 жыл бұрын

camera man puttin in work!

@boostedgringo5885 2 жыл бұрын

One recommendation for the future. Use factory crank and oil pump seals. Nice video, fun build

@gail8494 2 жыл бұрын

I can’t wait to see what you are making 3 yrs from now! Impressive ! Thanks

@SiggsGBR 2 жыл бұрын

In this video, a new cast member; Dropium

@RoflWolves 2 жыл бұрын

Damn the slider for the time lapse really is a game changer!

@_Gingium_ 2 жыл бұрын

Yeah! Super pumped with that investment!

@mikebanks6704 2 жыл бұрын

I'm beyond hype to see this build finished 🤘🏻🤘🏻

@brxezo 2 жыл бұрын

cant wait to see the completed build man keep at it its going along lovely

@natetaylor9187 2 жыл бұрын

Oh I count down the days to watch your videos, you are hands down my favorite to watch, i can’t wait to see this thing it action! So excited!

@kylemcweeny878 2 жыл бұрын

Same man nobody like the ginger!

@Outlier68 2 жыл бұрын

The engine looks so good in there. Really enjoying the content.

@johfur 2 жыл бұрын

Really enjoy your videos, keep up the good work! 😀

@wardaddy1114 2 жыл бұрын

Amazing work! You really deserve so much more than you get

@TobyBurt 2 жыл бұрын

Super cool build Gingium.

@walravenish 2 жыл бұрын

When building an engine and torquing every bolt to spec, use a sharpie to mark the bolts you have torqued, this way you don't have to worry about having missed any.

@nickgibb4687 2 жыл бұрын

Parts washer with water and actual CRC parts cleaner. fill the tub up just below the intake for the filter with water and the rest with CRC. the pump will only pump the oil-based CRC and the water will collect the crap. when you drain, have a petcock on the bottom and drain the water on the bottom until its clean make sure to fill up with water again. no waste in expensive actual parts washer solvent. Keep up the bomb videos

@coalblack 2 жыл бұрын

If you get another shot a weld repair on that casting, run 60hz with 80% balance to punch through the garbage casting. It helps to rasp the crack as well

@AWD_T 2 жыл бұрын

The front case seals in the topline kit will leak within a few years. Won’t be your problem though

@glenn9k 2 жыл бұрын

Amazing work as usual. Love it.

@Wafflebrah21 2 жыл бұрын

Seeing you add all those AN fittings, it made me think of something. And that's another AN fitting to a catch can. Awesome work dude, that welding table looks handy af

@koolpapiadam 2 жыл бұрын

Make sure next time when welding a crack, to drill a hole at the beginning and the end of the crack to prevent spreading

@gert-jandejong1832 2 жыл бұрын

Real awesome content, very nice to watch!👍

@avidworkslol 2 жыл бұрын

You should pick up an aftermarket j-pipe for that turbo -- They make a huge difference. Also, if it ever becomes an issue, they make alternator relocation kits for those that put the alternator on the other side of the block under the intake manifold.

@DingDongDrift 2 жыл бұрын

This thing gonna straight rip!!!!

@_Gingium_ 2 жыл бұрын

Absolutely!

@jake_bytheocean 2 жыл бұрын

Hey you should have some merch with the hip hop rim shop logo! I'd buy a tee-shirt :D

@1BadRAMLimited 2 жыл бұрын

Great work man!

@Wickedjc2119 2 жыл бұрын

Gotta get you a parts washer. Watching you use that foaming cleaner makes me wanna get a parts washer

@coreyjohnson993 2 жыл бұрын

Always relaxing vibes from your videos.

@TheGoodMedicine 2 жыл бұрын

500whp with that composite head gasket, well you will need loooots of luck.

@datalorian 2 жыл бұрын

Hell yeah for sonic tools. Sponsor spots I actually like to watch. Also like to hear your feedback over time on how they hold up. Hope comments like this help you get continued repeat sponsored videos with them. I am considering putting an order in next time I have tool money to spend. Cheers :)

@FineW_TurboM111 2 жыл бұрын

Dopamine, everytime. Thanks ging. Hope you get that 4G63T to 500Whp.

@kylemcweeny878 2 жыл бұрын

Bro legit his videos are like a drug man I need my fix 😭

@spikemic709 2 жыл бұрын

This is so cool and fascinating to watch

@maurocabello5421 2 жыл бұрын

bro you are a genius, continue like that

@stantheman5163 2 жыл бұрын

Congrats for keeping your cool when that housing cracked. Or did something get edited out? J/K. Looking good.

@radioactivegarage6967 2 жыл бұрын

I Never miss an upload man... You post, I watch.

@twinscrolled 2 жыл бұрын

Love seeing the work.

@herpsmcdirt 2 жыл бұрын

Have you done a video about how you got started in cars? I believe I remember you saying you didn't grow up a car guy, but are now. How idd you get started? You've learned so much over such a short span of time.

@isaactrockman4417 2 жыл бұрын

He used to do forza videos

@alessiocarlevaro6934 2 жыл бұрын

next time you crack something like that drill the end of the crack to stop it from propagating, corners are stress risers and the end of the crack is the most acute angle you can have

@kylemcweeny878 2 жыл бұрын

When he didn't start drilling and went to welding I told my wife "oh no he didn't drill it to stop it from cracking more". She has no idea what im talking about of course lol

@RearEngineShop 2 жыл бұрын

Watching this really makes me want another DSM. I miss my Talon TSI.

@brentconley8902 2 жыл бұрын

You have come so far since I started watching it's pretty amazing. That car is going to be badass. I don't think I have ever seen you so clumsy lmao. Take your time. Don't rush. You seem a bit nervous.

@limezsest 2 жыл бұрын

Good save on that damaged crank pulley tooth. I ran a damaged tooth on my mk5 GTI - I thought it'd be fine - it wasn't fine. Caused a timing belt failure which led to crushed valves.

@Can_I_Kick_It 2 жыл бұрын

Love what you’re doing to make the videos better and making your personal work load less!! But buddy’s gonna fry your cameras sensors filming welding that close up 😂😂😂

@Bshepdude 5 ай бұрын

the aluminum isnt garbage on that transmission bell housing, 1 you cleaned it with a steel wire wheel which adds impurities to the aluminum, 2 you didnt grind out the cracks so you were not going to get any penetration on that and 3 its cast aluminum so it has to be pre heated to take the weld nicely, not to mention on everything else you should have wiped it with acetone most of those welds probably are going to leak sooner than later.

@73Bugman 2 жыл бұрын

Great work G. So meticulous. Nice to hear of the Volvo's comeback. I still want you to name it "Chevolvo". 🖖👽

@nolanfoynes8022 2 жыл бұрын

i love your videos, I hope you do someting even crazier next time like a full tube frame car or dual engine or something like that! not everyone likes watching the process except for us build nerds!

@mastercricket7626 2 жыл бұрын

Heck yeah bro 💪 thing is come along and looking rad af 🤙🏽🤘🏼✌🏽.. peace n love brotha , build on stay safe and have fun broski

@reggie1753 2 жыл бұрын

i feel the pain of breaking a brand new part you are installing for the first time lol love what you been doing keep up the dope work. ps whats the best way for people to get a message to you?

@santosmedina4248 2 жыл бұрын

I think Patreon

@kylemcweeny878 2 жыл бұрын

I can relax now that I had my gingium fix....

@martinian0340 2 жыл бұрын

the video quality omg

@ZedChop 2 жыл бұрын

I wish I had a 6 bolt to build for my Talon! Its making shy of 350 awd right now i could just imagine what it would be like at 500 lol good job man Really love this Build

@Rodrigo_Esteban 2 жыл бұрын

Quality content 💯

@mauricepeters7684 2 жыл бұрын

for the next time installing a trans, they should just slide in with some wiggling. i was tought to never seat an trans with the bolts. you and i seem to have learned exactly why. otherwise your work is really cool! keep it up!

@MH-pe8wj 2 жыл бұрын

Mid engine 1g eclipse??? So cool 😎

@willmcpherson3760 2 жыл бұрын

Honestly short term those small cracks on the bellhousing will be fine. The bellhousing on my squarebody chevy was cracked 180° from top to bottom and i tried to weld it as well but that pot aluminum is suck garbage. I threw it back in as is and its held up to 400 ft lbs of torque, clutch dumps, and burnouts so id say its fine lol

@hotdogbuns255 2 жыл бұрын

can't wait to see the 4G prettied up before the giveaway

@makombost8140 2 жыл бұрын

The best part of waking up is the Gingium in my cup.

@josuepaz9446 2 жыл бұрын

so excited 😁

@jojii 2 жыл бұрын

I know it is a bit moot at this point, but whatever you are welding anything cast: iron, aluminium, chinesium, anything, you need to pre-heat the cast. The crystalline structure of cast is different from the "go and blow" of welding. Pre heating with a torch makes everything meet in the middle.

@febrianadji5758 2 жыл бұрын

👀 Having cameraman on shop give new look

@MichiganTrailRider 2 жыл бұрын

You need to graduate from internal gated turbos to external next !!! 😂

@-jaguarwarface2639 2 жыл бұрын

those cinematics of the tools looked awesome! cant wait too see this beast finally drive :)

@davidelliott8324 2 жыл бұрын

The Mitsubishi Delica/ L400 from the 90s had a 4g64. Maybe the dipstick and tube will be long enough for you to use since it was a longitudinally mounted engine in a cab over configuration. Good luck, great work!

@landon390 2 жыл бұрын

This was 🔥🔥

@andrewadam7043 2 жыл бұрын

Fantastic!

@packpower21 2 жыл бұрын

Install the timing belt cover so the uv doesn't rot the belt. Those motors don't need help bending the valves

@makeitorleaveit1 2 жыл бұрын

I like your choice of footwear it's real Gingium of you 👌

@samuelwildbore349 2 жыл бұрын

Loving th build Dude, just fyi for cast aluminium repairs where the area is greasy its almost guarenteed the internal of the metal will be too, so to do a decent repair you have to preheat the aluminium to remove as much of the oil as you can.

@davidguest5268 2 жыл бұрын

Volvo 5 pot would make the turbo rear facing, plus you will benefit from that awesome sound

@colinsanto2317 2 жыл бұрын

ARP studs are supposed to go in to the block dry and hand tight. You only are supposed to put assembly lube on the nuts to ensure proper torque.

@SeanOchoa 2 жыл бұрын

Dude, I love watching another builder of things work to put together a complex system like this. 50% art/50% flow state/50% mad scientist with some sick video to boot. Really enjoy your vids.