Building a Steam Box and Steam Bending Oak Frames, S2-E8

Рет қаралды 109,871

5 жыл бұрын

In this episode of The Art of Boat Building we follow along the building a steam box. The box is then tested for steam bending oak frames. The white oak frames are then installed in the Haven 12 1/2. Following a plan by Greg Rossel in his book "Building Small Boats" we see how to build a steam box for bending wood.
“If you’re going to make it, make it beautiful.”
Bob Emser
Subscribe for more Boat Building from The Art of Boat Building:
kzfaq.info...
Share this video with a friend:
• Building a Steam Box a...
How to support The Art of Boat Building.
Purchase Official Merchandise here:
www.bonfire.com/store/the-art...
Become a Patron:
/ theartofboatbuilding
Watch next
Recommended Playlists
Carvel Planking Playlist:
• Carvel Planking
Haven 12 1/2 Playlist:
• Season 2 - Haven 12 1/2
Tool Making:
• Tool Making
Let’s connect:
Facebook:
/ bobemseramericansculptor
Instagram:
/ artofboatbuilding
Twitter:
/ bobemser
Linkedin:
/ bobemser
Bob Emser American Sculptor:
www.bobemser.com
"Building Small Boats" by Greg Rossel
amzn.to/2SwkjG7
Video equipment used:
CanonM50: amzn.to/2TVob5l
Takstar SGC-598 (shotgun mic): amzn.to/2ZSVmup
Saramonic Lavalier Mic amzn.to/3drnZCK
Some of the power tools used in this episode:
Milwaukee 6391-21 15 Amp 7-1/4-Inch Circular Saw with Blade on Left
amzn.to/32Ftzwj
WEN 6530 6-Amp Electric Hand Planer, 3-1/4-Inch
amzn.to/2JP817W
WEN 6552T 13 in. 15 Amp 3-Blade Thickness Planer
amzn.to/2y1j9Ju
Bosch IDH182-02 18-Volt Cordless Impact Driver
amzn.to/32EGoqB
Disclaimer: Some of these links go to one of my websites and some are affiliate links where I’d earn a small commission if you make a purchase at no additional cost to you.
#theartofboatbuilding #artofboatbuilding #makeitbeautiful#woodenboatbuilding #buildingasmallboat #buildingasailboat #shipwright #toolbuilding #Haven12 #herreshoff #shipwright

Пікірлер: 87

@williamballew4443 5 жыл бұрын

I absolutely love your videos this is always been my dream to build my own sailboat I don't think I could do it like you though I never see you make a mistake LOL but I think you've inspired me to try thank you

@CarlWinter-oy8uf 3 ай бұрын

Nice workshop --wonderful when you can have all the modern latest tools and equipment at your fingertips! come to Africa --theres bugger all here mate !

@marcosrobertojuppa2107 5 жыл бұрын

I have to be very grateful for there being people like you who are predisposed to teach. As always a great video. Thank you.

@davidc6510 2 жыл бұрын

That steam box sure did work well with those frames. Great progress Bob. On to the next segment in this binge watch. Thanks for sharing.

@GoochPatrol1 5 жыл бұрын

What a great build series Bob! Thank you very much for the upload and we are all very excited for the next!!

@michaelclark2840 Жыл бұрын

That's a great build indeed. You can also have a small drain pipe from your weep hole feeding back into your boiler to recycle the water.

@TheArtofBoatBuilding Жыл бұрын

I did have a weep hole at the back (low end) to collect in a bucket. You’d be surprised how little I collected as the majority of the water evaporated in the steam. The collected water was quite discolored from the wood tannins, not very good for recycling. I just watered some plants with it. Clean water in your steamer keeps the vital parts clean. Thanks for watching!

@richardbohlingsr3490 3 жыл бұрын

The steam bent frames went well and they should last a long time. She is coming along great.

@alanhortin9620 4 жыл бұрын

So enjoying your series. Keep up the awesome work. Great video quality and production!

@shoresharp8349 5 жыл бұрын

Very nice and detailed video Bob thanks for all you do.

@andrewwhite6552 5 жыл бұрын

Really enjoying following along with your build!

@ChathamJackTar 13 күн бұрын

Superb. Thank you.

@tomtruesdale6901 5 жыл бұрын

Another great video, the boat is coming along and will be a beauty when she is finished. There is just something satisfying about bending wood. When I built my plywood Jon boat I didn't have an steam box for the plywood bottom so I put wet towels in a microwave till they were boiling hot and laid them on the area where I needed the bend to be. Worked like a champ. I used the same technique for bending the bottom runners but it didn't work out as well.

@dennisdownes9319 5 жыл бұрын

Very nice Bob.....great comments about not "over-pressurizing" the boiler and box! "They" make all kinds of rubber/foam pads to kneel on...........your knees will appreciate it! I love how a "first-fire" test turned into almost all the frames being done! Nice!!! DD

@lenniereagan2362 3 жыл бұрын

Thank you so much. Very helpful video. Plus, I really like your work.

@danwilley8695 2 жыл бұрын

Brilliant! Rarely have I seen an instructional video that did such a great job of very clearly explaining a complicated, involved, and extended process with such clarity and effectiveness. Also. your calm, soft-spoken demeanor makes the videos a pleasure to watch. As I told my wife, it's like watching Mister Rogers build a boat, which comment I hope you will take as the compliment is it meant to be. I have long wanted to build a wooden boat myself and when I get around to it, probably when I retire, I hope your videos will still be available. Many thanks for sharing this project with everyone!

@TheArtofBoatBuilding 2 жыл бұрын

Thanks Dan, I do take your Mr. R comment as a huge compliment. When you are ready to build stay in touch I think you’ll like the online boat building course I’ve developed. Thanks for watching! Cheers, Bob

@stevenpatterson5319 8 ай бұрын

Great work and documentation

@rt88glow 5 жыл бұрын

Great Video, Bob; thanks for the tip on the water level

@thomasarussellsr 5 жыл бұрын

And thanks to Louis from "Tips From a Shipwright" for providing this information for you to find/use. Great job giving credit where credit is due. Show that you are an honest person, thanks.

@michaelarmbruster586 Жыл бұрын

Nicetrick on measuring the water level

@SuperHyee 4 жыл бұрын

Thanks !

@migueldavidde 4 жыл бұрын

Obrigado por compartilhar. Abraços do Brasil!

@daleskidmore1685 5 жыл бұрын

I do like bending wood. I use a wallpaper stripper and vacuum food bag rolls and found that very effective, albeit slower. A luthier's bending iron can be useful too.

@sheiladunk7583 3 жыл бұрын

Hi,( roly) brilliant bubble tip,so simple but effective.

@postmortem8470 5 жыл бұрын

Dear Bob! This is a great and remarcably clear video as always. It might be too soon, but we would very much appreciate if you could show in a bit more details as of how the frames are located in keel area and connected to the floors. Thanks a lot!

@ront8270 2 жыл бұрын

I loved the video

@mrfrontranger7911 4 жыл бұрын

Sure do enjoy your videos

@robinhodgkinson 5 жыл бұрын

Nice going Bob. I wondered whether those ply ribbands would be stiff enough between molds, but those small frames, al dente, don’t appear to offer much resistance. : ) Looking forward to the next step. Your channel is sure making me want to build another boat - stop it, ok! : )

@user-zq5vu1im8w 5 жыл бұрын

Спасибо, очень интересно смотреть.

@bobolander 5 жыл бұрын

"have a little bit of an explosion" apparently this is contraindicated when steaming? great video!

@ranger2316 3 жыл бұрын

Like Norm Abrahms on New Yankee workshop says..." You can neve have too many clamps!"

@krockpotbroccoli65 Жыл бұрын

Norm was great.

@mattevans-koch9353 5 жыл бұрын

Bob, That steam box is the nicest one I have seen. "Just threw together some supports" would have taken me 3 days and half a dozen tries. Your sculpting background is really showing itself. Very nice explanations for the different steps you are taking and the video is very well done. Thank you very much for this video of your progress. Have a good week and looking forward to your next video.

@prestonbriggs5271 3 жыл бұрын

When you cut the frames from your slab, you can (should!) follow the grain to help avoid splitting when bending. You might end up with a crooked frame, but it won't matter since you're going to bend it anyway.

@OferNRaz 5 жыл бұрын

Great video Bob. One suggestion, you should avoid using iron fittings in the steaming box. It may make Oak wood black.

@hughbugger 5 жыл бұрын

Great video Bob. I would suggest you check the gain on your lav mic. Think it might be too high which is why you're getting some audio distortion. All the best

@jimjenkins673 5 жыл бұрын

Nice “test” ......16 frames later......awesome work.

@fernandofert9960 5 жыл бұрын

Bob looks like Capt. Sarigar!

@dinosaurus4189 4 жыл бұрын

You might want to look into steaming frames in a bag. It looks easier than the box.

@edwardschmitt5710 5 жыл бұрын

"A shipright name Lou" huh? Louis Sauzedde by any chance?

@gwkdad 4 жыл бұрын

Yeah, I'd like to know what happened to Louis. Why did he fall off the earth?

@andorsary4476 3 жыл бұрын

Last time i looked around in my shop, i kind of got confused about which one of my machines is the lathe. Can i borow your method? 😆

@prestonbriggs5271 3 жыл бұрын

Working with 2 people can go a lot faster. We tried to put the frame approximately in place and get the bulk of the bend done very quickly by hand, then add clamps, to avoid too much cooling.

@bjornsmasher66 5 жыл бұрын

if wood splits along the medullary rays wouldnt it be better that you lay the rays parallel to the planking? when your boat gets old and the frames dry out and the frames check, the screw will still hold the now two layer frame rather than the screw pulling through the check. im sure youll counter sink the screws anyway so there shouldnt be a chance youll split the frames while fastening the planks.

@HB-jd3ko 4 жыл бұрын

Precisely as recommended by Louis Sauzedde (Tips from a Shipwright) for that reason. Coincidentally, using the example of frames in a Herreshoff 12 1/2.

@tomasgabinus677 4 жыл бұрын

Yes, also saw Louis recommendations and it seemed correct. Fantastic work no matter what.

@the382house 3 жыл бұрын

Did yo pre-cut the ends for the frames to meet the stem and bed logs?

@dcjdesign_7892 3 жыл бұрын

"a shipwright named Lou" ;) ;) ;)

@dennisboisen 5 жыл бұрын

Nice build However it's not exactly healthy to warm something up which has been galvanized...

@oakleyjack7600 5 жыл бұрын

Could you clamp each section up and replace the clamps a station at a time with zip ties to negate not having enough clamps. ?

@TheArtofBoatBuilding 5 жыл бұрын

Yes, one could do that. Best to let them cool first.

@garryjackson3941 5 жыл бұрын

outstanding work.....wished you were my neibour

@thomasarussellsr 5 жыл бұрын

Just trying to help, not troll... Neighbor is the proper English spelling, not neibour. Hope this helps.

@gbexpatcornishman3004 5 жыл бұрын

... ditto ... 'American' SP = neighbor ... English SP = neighbour!

@johnshoureas1629 5 жыл бұрын

Is there a reason you didn't rout a small radius on the corners of those frames, prior to installing them ?

@brinjoness3386 5 жыл бұрын

best to fair them out when you install planks i think. gets a closer fit, and you don't want places to trap water.

@bizim_eller 3 жыл бұрын

I got that"tip from a shipwright" called lou🙂🙂🙂

@davidh4581 4 жыл бұрын

Bob, was the stock you used for the frames 'green' or dried?

@TheArtofBoatBuilding 4 жыл бұрын

David H it was Air dried. Not Kiln dried.

@CorwynGC 4 жыл бұрын

Also steam is a problem for most glues.

@jasonturgeon195 2 жыл бұрын

Nice build! Did you do a test burn of the pot outside? That galvanized steel is toxic when reaches 392 degrees F. the zinc will burn off creating yellowish fumes. Please be careful when heating Galvy

@TheArtofBoatBuilding 2 жыл бұрын

Yes, I'm fully aware of the hazards of zinc. I was only heating to steam temps. (212ºF) The steam pot was always outside with the large doors open for ventilation. Cheers, Bob

@danbair3752 4 жыл бұрын

Love the show? How much was the kit in season 1?

@TheArtofBoatBuilding 4 жыл бұрын

I purchased my kit as apart of the class I took at the Great Lakes Boat Building School. So the kit was part of the tuition. Here is a link to the kit by CLC www.clcboats.com/shop/boats/wooden-sailboat-kits/tenderly-dinghy.html Thanks for watching!

@anthonymoraes3251 3 жыл бұрын

Is there any concern about mold building up over time from the moist heat and cooling and heating again on the inside of the pine box?

@TheArtofBoatBuilding 3 жыл бұрын

Been steaming in the same box for over a year. Very clean inside, so no concerns.

@anthonymoraes3251 3 жыл бұрын

@@TheArtofBoatBuilding thanks! Great videos by the way....!

@Monsieur.Nobody. 2 жыл бұрын

That's amazing! What type of wood is it if I may ask?

@TheArtofBoatBuilding 2 жыл бұрын

White Oak

@Monsieur.Nobody. 2 жыл бұрын

@@TheArtofBoatBuilding nice! Thank you!

@sabinfarm7243 Жыл бұрын

How can I get the book? in Indonesia the book is still rare

@TheArtofBoatBuilding Жыл бұрын

What book are you interested in?

@johnlinehan9053 4 жыл бұрын

PVC steam box looks like a banana after it heats up.

@thomasarussellsr 5 жыл бұрын

I absolutely love the content, but it is really hard to hear you much of the time. Does your editing software have the ability to increase the speaking volume? Thanks for your consideration.

@hedhtr4 4 жыл бұрын

Many woodworkers prefer steambox made of metal because they do not absorb the steam.

@WildBoreWoodWind 4 жыл бұрын

Your nice galvanized container, should give you a good dose of metal flu. :0/ You shouldn't heat up galvanized metals enclosed areas, you literally can die from the fumes.

@ThomasMorleyceramics 4 жыл бұрын

your steam box should be insulated

@alexandermessier5509 5 жыл бұрын

you never want to run your steam box in the shop everything made of metal will rust

@mysterymete 5 жыл бұрын

If run outdoors, the entire forest will spontaneously combust and cause democrats to overheat, which leads to global warming and communism. There is no free lunch.