MF135 6 Speed Restoration #44 How to Remove Your Hydraulic Lift Cover

Рет қаралды 67,535

5 жыл бұрын

How to remove your MF135 Hydraulic Lift Cover.
In this video I go step by step removing the hydraulic lift cover on our 135 tractor.
This is the same process for the MF148, 165 and many other 100 series Massey Ferguson tractors.
Parts seen in this video can be purchased from.
www.queenslandtractorspares.com.au
If the parts you need is not on our web site, ph1300 850 097 and talk to us directly.
or
E Mail: info@queenslandtractorspares.com.au

Пікірлер: 61

@bluegrallis Жыл бұрын

This is easier to watch, than to try and read the manual for the disassembly process. With the problem I have(mentioned in my recent email about my 230) I believe I first need to drain the oil down far enough to remove the right side cover, with the response control, to see if my roller is in place properly. Thanks for your videos and help.

@BundyBearsShed Жыл бұрын

Yes worth a look I would think.

@georgesims6122 5 жыл бұрын

What a wonderful teacher you are Lance I have a 6 speed 135 which I use for road runs & shows.I may be 74 but I am learning more from you than out of a manual. I also enjoy your machining. I used to have access to a lathe & milling machine. THANKS.

@BundyBearsShed 5 жыл бұрын

Thanks George, Im glad you get something from the videos. hopefully this one will see some runs as well.

@TXHeat1776 5 жыл бұрын

Excellent, this was exactly what I needed and covered all the steps from the shop manual that had me scratching my head. Thanks

@BundyBearsShed 5 жыл бұрын

Glad it could help.

@TheRamsalt 4 жыл бұрын

Thank you for this great video series. It has been a fantastic resource and help tinkering with my MF 148.

@BundyBearsShed 4 жыл бұрын

Thanks, Glad you enjoy it.

@mizanulhaque5649 3 жыл бұрын

@@BundyBearsShed য়ধ

@davidsample9130 5 жыл бұрын

Very good I have to free up the levers on my mf 230, nice to know about that roller, thanks for that one!

@BundyBearsShed 5 жыл бұрын

Thanks Dave.

@Tomzenzo 2 жыл бұрын

Excellent video! Keep up the good work!

@BundyBearsShed 2 жыл бұрын

Thanks, will do!

@stevefuller1779 3 жыл бұрын

I have the correct tool for removing these covers and, in fact, they hinge over backwards and have a leg bolted onto the seat studs, all works very nicely.

@BundyBearsShed 3 жыл бұрын

I sold mine when I sold my workshop a few years back now. i dont do enough to worry now.

@LeeWire 6 ай бұрын

Great video. I have a lift issue where the lower lift arms won't go down far enough on a 66 UK 135, otherwise lift is raising and lowering ok. Can I adjust the bottom screw at 9:12 to make the lift arms go down further? Lift needs to drop maybe another 6 inches. I have no pressure control, just draft & position.

@BundyBearsShed 5 ай бұрын

No I dont think so, possibly lift the top of and run through the correct adjustments and it should come good.

@daveklooster4905 5 жыл бұрын

It's nice to know about that roller and how easy it is to remove to avoid bending the rod. I sometimes tug on things that don't move like I think they should and would have bent that rod for sure.

@BundyBearsShed 5 жыл бұрын

G Day Dave I see many like that.

@viveknarayan7673 5 жыл бұрын

thanks for ur video sir.

@BundyBearsShed 5 жыл бұрын

Thanks Vivek.

@user-rw6bl1oz6n Ай бұрын

Lift works when tractor gets warm lift slow raising back to up position

@BundyBearsShed Ай бұрын

Try replacing the stand pipe o rings first but it can be from a worn pump.

@randallhorner5970 Жыл бұрын

Lance, I have a UK 135 that when I use the hydraulics the pump is pulsating even shakes the tractor while it has a load on it. Any Ideas, thanks

@BundyBearsShed Жыл бұрын

They will do that under load at times and it is bad when there is a leak some times. I think the pump may be well worn.

@randallhorner5970 Жыл бұрын

Thanks

@boonies70 4 жыл бұрын

Mr. Bundy...in the first segment of this video I see your draft and position control and I just noticed that your position control plate is backwards...at least compared to my MF 20 Industrial. Even the label on the plate seems to indicate this with the up position being labeled as down. Shouldn't the two concave sides face each other? Thanks for the video...I'm about to tackle this myself!

@BundyBearsShed 4 жыл бұрын

We found out since there is two plates or versions, Im not sure about which is which at present.

@donotcallmesusan6856 3 жыл бұрын

Does anyone know what size allen wrench works for the screw on the right side cover?

@BundyBearsShed 3 жыл бұрын

Im not sure I would have to check, measure across the flats.

@richyphillips Жыл бұрын

HI, great video series. I have an MF250. The rear lift arms are not responding to the controls. They lift when I first start the tractor (in the transport postion), but if I lower them, they will not lift again until I switch off the tractor, wait a few minutes, then start it again in the transport position. If I put an implement on the back, the lift is very slow and juddery but still will not respond to the lift control. What could be the cause?

@BundyBearsShed Жыл бұрын

It sounds like a sticky pump control valve, Pull the rh trans cover off and see if you can see what is going on.

@richyphillips Жыл бұрын

@@BundyBearsShed Thanks, I'll get it apart and give it a test.

@richyphillips Жыл бұрын

@@BundyBearsShed Yep, needed a bit of effort with a screw driver to push it toward the front of the tractor. It's freed up a lot now. Need to drain and renew the fluid now, it was milky. Replaced the gear shift rubber too, hopefully less water will get in now.

@richyphillips Жыл бұрын

Spoke too soon. I put the loader on, fine, move the lift arms, fine, attached a box grader, it won't lift it and then the loader wouldn't lift either. If it's the control value, that looks like a big job :-(

@richyphillips Жыл бұрын

The control valve was stuck again, so I freed it up, but the loader still moves at less than a snails pace. I have a pressure gauge on order but I reckon there is not enough pressure to lift the loader.

@ShainAndrews 5 жыл бұрын

Audio level issues. 11:00 Levels jump up (to where I believe they should be). 12:00 Drop back down (to levels that I believe are lower than they should). I've noticed on the last few videos the levels all seem to be to low. At that 11:00 minute mark I can hear the details of the shop, but nothing is obnoxious. I expect to hear the shed, foot steps, etc. Hope that helps so you have some specific spots to see the differences in those levels.

@BundyBearsShed 5 жыл бұрын

Ill go for a look, plenty to learn yet.

@ShainAndrews 5 жыл бұрын

@@BundyBearsShed Well that explains the issue! Ol Lance is having a look when when he should be havin a listen! You're doing a fine job. I'm always amazed at the content. It's not easy trying to get something done then add a camera... and now mics, and booms, and... where does it stop? LOL

@tjohnson9051 5 жыл бұрын

I'll second that. the volume has been low since the new microphone setup. What Shain said is about right for my computer with 80 watt separate amp and speakers. I have KZfaq volume all the way up and the one on the monitor then my Amp is at almost 3/4. At the 11:00 mark is good and it matches other You Tube channels. PS not wearing flip flops today -26C. Freezing my banana!

@BundyBearsShed 5 жыл бұрын

@@ShainAndrews Just revisited and the editing file is pretty much the same all along, next videos will have normalize function used in editing and and we will see the difference.

@BundyBearsShed 5 жыл бұрын

Ah Im onto it, even though the levels in the editing are the same with volume on the time line it is in the size of the wave form. Biggest mistake you make is thinking I know what Im doing, lol.

@filiper78 4 жыл бұрын

hello my lift of my mf 135 does not want to drop just if it is weight. anyone have an idea??

@BundyBearsShed 4 жыл бұрын

Possibly the bolts at the end of the rockshaft are too tight.

@joe1212a 3 жыл бұрын

Wondering if you have any idea why my Massey 245 lift arms stutter when lifting. They lift fast and strong and go down smooth but they just have this tremble while going up. I removed the Lift Pump, stripped it down completely, immaculately cleaned it, replaced all oring's and back up washers, new piston rings, new pressure relief valve, fresh new Permatran 3 oil in the sump and it made no difference at all. All the pump parts that I didn't replace looked to be in great shape. The tractor only has 1000 hrs and has been always stored inside. No rust on anything. Now I'm unsure where to go from here. I feel like it should lift buttery smooth. Could it be the lift cover? Also the lift arms do not leak down when left overnight or longer. I'm stumped Sir. Wondering if you have any ideas? Any help would be greatly appreciated.

@BundyBearsShed 3 жыл бұрын

Some do lift smooth but it often depends on the load on the arms, Its hard to say without being there.

@joe1212a 3 жыл бұрын

@@BundyBearsShed This is with almost no load on the arms. Just me standing on them. At this point I'm just going to put it to work and see what happens. Who knows maybe it'll smooth out with use. Cheers

@isakosal3432 4 жыл бұрын

HELLO BY MR BUNDY BEARS SHET USE PLOW..WHICH ARM SHOULD BE USED? SLOW OR FAST ARM

@BundyBearsShed 4 жыл бұрын

Draft lever

@isakosal3432 4 жыл бұрын

@@BundyBearsShed I don't understand what you mean..Draft lever?? fast lever or slow lever.. WHICH ??...for plow...

@venailsonsantos6241 Жыл бұрын

Muito bom

@BundyBearsShed Жыл бұрын

Thankyou.

@hueykimlin4958 5 жыл бұрын

WTF Lance, First time I've seen you use a rattle gun. Are you in a hurry or trying to hide the creaking shed noise. Love your vids and safety thongs. All the best and keep up the excellent work. Huey

@BundyBearsShed 5 жыл бұрын

G Day Huey, Yeah I must be getting lazy. The rattle gun is a bit savage on the small engine bolts I thought.

@TheUltimate65 3 жыл бұрын

Must be early gray types of ferguson that..

@BundyBearsShed 3 жыл бұрын

Yes 1948

@elvinsanchez7962 4 жыл бұрын

Primo una pregunta

@BundyBearsShed 4 жыл бұрын

Happy New Year!

@AdrianHiggins83 5 жыл бұрын

Hi lance I think you need to normalise the audio take a look at kzfaq.info/get/bejne/iNBnpsVz082RhGw.html otherwise good start 🤛

@BundyBearsShed 5 жыл бұрын

G Day Adrian, Yeah it looked ok in edit (didnt really know what I was looking at lol) but I used two different sources for sound. I think i have it sorted, next videos will be louder too I think.