Sparex Ferguson TEA20 # 28 Fitting the Timing Chain and Setting Cam timing

Рет қаралды 19,990

4 жыл бұрын

In this video I cover how to set up the timing chain correctly and fit it all up.
Here is a link to the Kangaroo Stew where I bought it and got it running.
• Kangaroo Stew # 165 I ...
Some of the links I talk of in the introduction are below.
Queensland Tractor Spares Web Site:
www.queenslandtractorspares.c...
Queensland Tractor Spares Ferguson Parts Category Short Cut:
www.queenslandtractorspares.c...
Queensland Tractor Spares Technical Tab:
www.queenslandtractorspares.c...
Queensland Tractor Spares Downloadable Sparex Catalog Tab:
www.queenslandtractorspares.c...
Sparex Australia Web Site:
au.sparex.com/

Пікірлер: 34

@TheKnacklersWorkshop 4 жыл бұрын

Good video, I really enjoyed it Thank you

@BundyBearsShed 4 жыл бұрын

Glad you enjoyed it

@stuartmaier2465 4 жыл бұрын

Hi Lance, this is not something you want to read; I have a bad feeling that the chain retainer clip went on the wrong way around (although it's difficult to see). My understanding is that the head points towards the gear that pulls.

@BundyBearsShed 4 жыл бұрын

Yes thats what I did I think, I will have to run through now and have a look, lol.

@BundyBearsShed 4 жыл бұрын

Yep on back to front. Not a big worry though but I might pop the cover its only a pulley and a few bolts.

@onkargill8236 3 жыл бұрын

I've done the same thing 😂 put the chain retainer wrong way even though I was thinking it should be the other way but I thought you can't be wrong 😃🤣 so it's timing cover off again 😅

@connormacmillan839 Жыл бұрын

Hi lance, im fitting a new timing chain to my ted 20 tomorrow, the crank sprocket been touched since i took the cam sprocket off, however i didnt put witness marks on the cam sprocket. There is a witness mark etched into the crank pulley but im concerned that ive messed the timing up. Any help?

@BundyBearsShed Жыл бұрын

Yes I think there is a mark. Download the manual from my QTS website to be sure. queenslandtractorspares.com.au/technical/

@connormacmillan839 Жыл бұрын

Thanks for the help lance, fitted new belt today, top side is pretty tight but underside is sagging, thinking its because the sprockets aren't new!

@denniswilliams8747 4 жыл бұрын

I am puzzled about the crank shaft shims. What about the end play in the crank? Thanks for the vids

@BundyBearsShed 4 жыл бұрын

This is not adjusting crank end float we did it with the crank thrust washers, this is just to align the sprockets on the crank front snout.

@edwardmuirhead6726 Жыл бұрын

Good day Lance , I took the 5 bolts off the cam sprocket on my TEF today , lost the settings as I hadn’t realised multiple settings , could you please advise me how to get it back to the correct position please ? Thanks again , Ted

@BundyBearsShed Жыл бұрын

I would have to look in the manual it has been that long since I did one. There is a free manual in my website www.queenslandtractorspares.com.au in the technical section.

@edwardmuirhead6726 Жыл бұрын

@@BundyBearsShed Thank-you Lance , your help as always is very much appreciated , I will look that up , all the best ! Ted

@alexandercotter707 4 жыл бұрын

Hi Lance, I’m hoping to can help me. I’m looking at purchasing a TEA20 but it has a broken timing chain and timing case cover. My question is it worth repairing or will the pistons have bent the valves? TIA

@BundyBearsShed 4 жыл бұрын

Valve will probably be ok as they didnt lift that much really

@alexandercotter707 4 жыл бұрын

Bundy Bears Shed Thank you for the advice

@JACKATTACKED 4 жыл бұрын

Gravity is back 😂👍

@BundyBearsShed 4 жыл бұрын

It never left.

@JACKATTACKED 4 жыл бұрын

Wouldn't be right if it never gave you a reminder now and again 😂

@pm270100 Жыл бұрын

a woody that be red gum

@BundyBearsShed Жыл бұрын

Yep

@darrenblattner2508 4 жыл бұрын

So my John Deere has an idler gear rather than a chain. If I set the piston at TDC and set the valves at .010 (or 0) my idler gear should just slide in and mesh nicely? Maybe? possibly? Then with my rotor pointing at #1 piston it should slide in nicely as well? Perhaps? Welders playing mechanics!!!

@BundyBearsShed 4 жыл бұрын

For yours you need a steel ruler which welders will have for sure. Just align the marks through the center of the crank and pop the idler in.

@darrenblattner2508 4 жыл бұрын

That’s almost to easy Lance. Thanks

@453421abcdefg12345 Жыл бұрын

I think you put the chain link clip on the wrong way round, the closed end should face the direction of rotation ,the way it is now could result in the spring leg catching and removing the clip, good luck Chris B.

@BundyBearsShed Жыл бұрын

I would need to go back and have a look, it is running well still. Sometimes when filming the end result on the video may not be the actual end result if I have had to do a few takes.

@453421abcdefg12345 Жыл бұрын

@@BundyBearsShed i am sure filming and fitting are a very big problem, it must be like trying to talk to someone while you are putting something back together, looking at your re assembly of the timing cover video I can see that if the "mushroom" was sticking in the centre shaft hole that could cause my problem, a video is worth 2 thousand words! Chris B.