CALIBRATE 1V/OCT TRACKING ON ALL YOUR OSCILLATORS FAST

Рет қаралды 4,952

Күн бұрын

Calibrating analog oscillators to track properly 1 volt per octave scale sometimes becomes a huge problem. Not anymore: after that Christmas edition video you will learn how to trim v/oct using our approach which you can repeat using your own tools on any oscillators during holidays season.
Happy holidays!
Content:
00:00 Intro
00:56 Calibrating the Furthrrrr Generator's Carrier VCO
06:44 Calibrating the Furthrrrr Generator's Modulator VCO
08:55 Calibrating the Godspeed VCO
11:54 Calibrating CV outputs of the Shuttle Control
14:52 Calibrating CV outputs on the Ground Control
Modules used in that video:
FURTHRRRR GENERATOR: complex vco with waveshaper
www.endorphin.es/modules/p/fu...
SHUTTLE CONTROL: usb/midi to cv converter
www.endorphin.es/modules/p/sh...
GODSPEED: complex VCO with autotune
www.endorphin.es/modules/p/go...
GROUND CONTROL: performance 8 drum tracks / 3 melodic tracks sequencer
www.endorphin.es/modules/p/gr...
AUTOPILOT: dual autotuner for oscillators
www.endorphin.es/modules/p/au...
For more information about ‪@Endorphines‬ check out:
Instagram: / endorphin.es
Facebook: / theendorphines
Twitter: / endorphin_es
Modulargrid: www.modulargrid.net/e/modules...
#eurorack #endorphines #calibration

Пікірлер: 18

@saschaz1 Жыл бұрын

Explaining the process just helped me a lot. One thing that might also be important is to wait a couple of minutes until the oscillators are warmed up. Thanks a lot!!!

@modularsoundbath 2 жыл бұрын

Now I am ready to tune my oscillators, thank you for making this video! :)

@auctor11 2 жыл бұрын

Fantastic Video! Just what you need! Thank you!

@spaceoutservice681 Жыл бұрын

Wow. This was very helpful. And I was able to successfully calibrate my furthrrr generator. Thank you very much for this!

@Datachrome 2 жыл бұрын

Nice new front panels for that Furthrrrr!

@sleaztek 2 жыл бұрын

Yesss i know need to tune my Furtherrr thanks for this one now i know how...looking good in silver to...🖤

@muratonal3906 2 жыл бұрын

Wir freuen uns, Ramses Electronic Imaging and Sound Systems unter uns zu sehen.

@HarryKelvin 2 жыл бұрын

Where did you get the Supremesque Eurorack shirt?

@PhatNoizeRecords Жыл бұрын

Thanks for the video helped a little bit. I got a Behringer 921B Oscillator which i messed up completely due to missing knowledge :-). This OSC has 3 trimers (VR1 FREQ ADJ, VR2 HI ADJ and VR3 SCALE). My main issue is, that at one point I can not trim further down (trimmer clicks, stops in the khz range). Is there any advice you can give to set the trimmers to an initial state like turn trimmer xyz completely left, right or to middle etc. before starting the calibration that I'm able to dial in the lower frequencies? Many thanks.

@Endorphines Жыл бұрын

Hi. From our experience of you were running out of useful scale squeezing turns, usually going up or down one-two octaves helps to get into a useful range and try to tune again

@PhatNoizeRecords Жыл бұрын

@@Endorphines I give it a try, thx

@AaronGoldbergMusic Жыл бұрын

is there any sort of confirmation the calibration is writing? I have tried following the video, but my outputs remain consistently off... the same measurements as before calibration

@deadlinkofficialartst5592 Жыл бұрын

i got to do this with my grandmother moog lmao

@miguel.chambergo 9 ай бұрын

I don't see why the trimmer has to be at the back of the module and I don't see why should you need a trimmer either. It doesn't make any sense to me. Like, when tuning a guitar, the pegs are easily accessible. In an ideal world to me, you should be able to tune them with just a knob at the front of the panel, without having to disassemble anything and without the need of tools like a screwdriver. Yes, I know this is not going to be a popular opinion.

@elecsoul8309 2 жыл бұрын

Where did all the mushrooms go? No more cows? 😲

@FlesYm80 Жыл бұрын

Hi friend, thank you very much for this video! Just a little question: i need to calibrate my Doepfer Dark Energy III, and i ask to you (if you know) if the procedure is the same? Know you what is the trimmer to calibrate the oscillator? I try anyway to calibrate it! Thanks a lot!🙏🏻☮️

@Endorphines Жыл бұрын

Yes bro, the procedure is same for all the oscillators just the direction of the trimmer may be opposite

@FlesYm80 Жыл бұрын

@@Endorphines Many thanks friend! I’ll let you know!🤞🤞