CAN-AM Front Differential Removal, Reseal & Reinstall [12- Current Gen 2]

Рет қаралды 11,798

Жыл бұрын

Hello my friends, I have prepared a video that will show you the quickest way to remove a front diff from any gen 2 Canam (12-current).
No matter if it's a renegade or a outlander, they are the same front diff and suspension in all engine sizes. No matter if it's a 570,650,850,1000r they all have the same suspension and front diff assembly. The long and short frame have the same front setup except If you have the 4-Lok diff, you just have to disconnect the extra plug for that. I hope this video saves you money, provides clear guidance and shows you that you can do it just like I did. If you need to rebuild the diff, do so and then follow the video for reinstallation of the diff.
SPECIAL TOOL NEEDED: Axle seal puller
LIKE, SHARE, AND SUBSCRIBE !!! THANK YOU!

Пікірлер: 24

@Maxsmotoshop 5 ай бұрын

I like how you tried to show us how to pull the diff out, and then magically appeared in your bucket, was really helpful

@TFPVIDS 5 ай бұрын

It took me a while to figure it out honestly but it's just rotating and going up and out and figuring out how to work around what's there. It did stump me also so that's why I forgot it and I apologize about that.

@notrailsneeded Жыл бұрын

excellent camera work & lighting. Informative and to-the-point explanations along with useful tips & tricks. Great editing.

@TFPVIDS Жыл бұрын

Thank you 🙏

@michaeljohnston9085 6 ай бұрын

Litterally came here too see if the drive shaft collar at the pinion seal was removable as I'm retro fitting a 4 lok diff into my 2019 outlander xmr. As a mechanic myself i was to stubid to clean the grease from it to see the bolt first hahahah. Thanks for the great info.

@TFPVIDS 6 ай бұрын

Well you got it, they are removable! Grease always hides stuff 😂

@PFCYANEZ92 4 ай бұрын

Bad ass video! Thank you

@TFPVIDS 3 ай бұрын

Thanks

@caesarray4597 Жыл бұрын

A well made and very informative as well as instructional video.

@TFPVIDS Жыл бұрын

Thank you I tried to hit everything in 1 video!

@javiergallegorodriguez8325 Жыл бұрын

Good morning from Madrid, Spain, I want to congratulate you on the video and thank you for doing it, the images are very good and encourage you to dare to do it, I have seen it through the front transmission output cross, which I can not grease because the greaser is turned, and although it has not given me problems (at the moment) but the grease will give me, greeting P.S. I have an outlander 800 2008 and I'm delighted.👊🏼✊🏼💨💨

@TFPVIDS Жыл бұрын

Thank you very much! my video wont apply to your model specifically as its a gen 1 but we appreciate the support!

@NBADVEnduro Ай бұрын

Where did you buy the seals? Part number?

@sicodecsarl9249 2 ай бұрын

Hi, can you install a torq locker in a differential (btc abs) for Europe thanks!

@TFPVIDS Ай бұрын

When we get one in we will film the process but none have come up yet 💪

@eighty6ramam 6 ай бұрын

The one part i came to see was edited out. The actual removal from the frame.

@TFPVIDS 5 ай бұрын

Sorry I had to trim it down and missed that step 👍

@B1ou1nsGarage 5 ай бұрын

Did the shaft where the driveshaft goes into the collar spin freely? Once it was out the bike

@TFPVIDS 5 ай бұрын

I didn't check but mechanically speaking, it should spin freely with no 4x4 engaged.

@brandonmartinez7807 Жыл бұрын

what type of greese did you use?

@TFPVIDS Жыл бұрын

Waterproof Green Grease in a green and yellow tube, Best stuff and wont water down over time stays in the bushings!

@TFPVIDS 5 ай бұрын

I use a green grease that is for equipment and won't wash out as fast it's available at ace hardware.

@Mudslinger2011 Жыл бұрын

First video I’ve seen where a guy can’t afford a set of wrenches. 😊

@TFPVIDS Жыл бұрын

Boss Tools are tools, weather it's name's brand or Harbor freight that doesn't make the Job. The job makes the job. I do have wrenches but who works fast.....with manual wrenches. To each it's own. Stop the 🧢