Can-am Maverick X3 Greasing wheel bearings

Рет қаралды 6,186

2 жыл бұрын

The wheel bearings on a Can-am Maverick X3 come with little to no grease in the wheel bearings.
In this video we will show you how to grease them with a special tool and wear you can get the tool.
Don't wait to burn up the bearing on your machine.
Grease Bearing tool-- www.amazon.com/gp/product/B07...
Maverick X3 Torque specs
Torque Specs for Brake Caliper bolts- 37 Foot Pounds
Torque Specs for CV axle castle nut- 184 Foot Pounds
Wheel Lug nuts- 70 to 75 Foot Pounds
Other related video on our channel..
Changing out a wheel Bearing on a Car- • How to replace a bad W...
Can-am X3 first Oil change and Service- • Can-am X3 first oil ch...
How to compress and change Struts and springs- • How to compress Strut ...

Пікірлер: 17

@toddpamworkman4329 Жыл бұрын

Thanks for the great info!!

@fennkevin 2 жыл бұрын

I've got the same exact machine as you (2020) and I just hit 3500 miles. I'm thinking it's time to grease mine as well. Thanks for the vid!

@reviewittv1802 2 жыл бұрын

Thanks for checking out the videos.

@kanomh8445 Жыл бұрын

Thank you for the video

@narfwar2070 2 жыл бұрын

Fun video

@grantparnes 10 ай бұрын

White grease is usually lithium grease and reacts with other greases, and they destroy each other. Always clean one type of grease out of something before changing to another type of grease. Can am is not stupid, if it were meant to have an entire tube of grease in each wheel bearing, they would have put it in at the factory. Curious what the owners manual says about the bearings.

@nghtrdr84 2 жыл бұрын

Just greased up one bearing lol 3 to go- again thanks for the great details 👍

@reviewittv1802 2 жыл бұрын

No problem

@narfwar2070 2 жыл бұрын

Have the same Geese gun lol .. is a pain in the ass...

@shaneward4065 2 ай бұрын

Is that a 39mm tool on the maverick?

@ronmaynard7424 7 ай бұрын

How have the bearings been holding up? Imo that is way to much grease, there is a reason sealed bearings arent packed full, it causes heat, and leaves on room for expansion. 2 maybe 3 pumps after the tool is full and thats it for me, ive seen to many ober greased trailer bearings come apart, auto makers dont have provisions for greasing wheel bearings like this, but curious since its been a few years what your results have been?

@reviewittv1802 7 ай бұрын

Thanks for keeping up with the channel. Believe it or not, I have had no issues with the bearings and have not greased them again at all since the video with several trips since then. In fact, we just took a 15-20 mile trip through the Perco canon of New Mexico, and she ran like a champ with no bearing issues.

@domstarkey7279 11 ай бұрын

I've got 3 of these so far an none of them will fit over the rc axles

@reviewittv1802 2 жыл бұрын

The dealer's or manufactures won't dare mention the wheel bearing come ungreased.

@joemomma4482 2 жыл бұрын

Shock therapy recommends not greasing can am bearing’s.

@Scob55y Жыл бұрын

Did they give a reason why?

@ronmaynard7424 7 ай бұрын

I would agree more w ST then this method, this is way over greased. There is now no room for heat expansion and your creating more friction and less room for expansion. I would say pump the tool full, then install in the hub maybe do 2 pumps and that's it. Bearings don't even like being fully submerged in oil let alone grease, just look at oil bath trailer axles, you only fill them 1/3 full. Just my .02