How to grease the wheel bearings on a can am maverick x3
Пікірлер: 29
@chicago16802 жыл бұрын
Just fyi on the end of your grease gun where you plug it into the zerk fitting that you can loosen and tighten that way you arent struggling pulling it out or mess up the zero fittings. You loosen it then put it on then tighten it. Pump your grease then loosen it and voila no tugging or pulling. I guarantee your grease gun has this on the end. Most people don't know that
@powderriver24244 ай бұрын
Just an FYI all new bearings are barely greased when new. You must grease all new bearings during the install on any brand of machine.
@grunfieldf86944 жыл бұрын
It's the supplier that they get their bearings from falt. Replaced axle bearings ,Honda ATV, new bearings same, no grease. Repacked before install.
@Clockburner5 жыл бұрын
Do your wheel a favour and get rid of those rock guards.
@jasoncolemanarizonaloanoff1574 Жыл бұрын
I tried pulling the rotor off and it dragged the bearing with it...the front 2 no problems. That bearing must have froze to the rotor or something.
@lonnieschwersenska1335 Жыл бұрын
Hay guy was that grease tool a 39mm iv got a22 xmr x3and the grease tool is way to small
@juan68468 ай бұрын
What measurement is the wheel bearing greaser ?
@jasonrodriguez6372 жыл бұрын
One of my axles didn’t have a cotter pin from factory.. :/
@6lastresortАй бұрын
Were you having abnormal vibrations at certain speeds before you did all this?
@2FAT4URACINGАй бұрын
No just normal maintenance
@6lastresortАй бұрын
@@2FAT4URACING okay thanks for the feedback.
@JL-ep1rb4 жыл бұрын
That’s too much grease buddy, too much grease is also just as bad as no grease at all. It overheats and causes premature wear and failure. If you have to fill up your bearing with grease to remove the play, you got a bad bearing and it needs replacement. Now the grease pushed out the seal to come out, she’s not sealed anymore. Look it up buddy, just do 5-6 pumps like twice a year that’s plenty
@jasoncolemanarizonaloanoff1574 Жыл бұрын
How much did you sand down that cheap little tool? I can not seem to get mine in for the life of me
@davidn80453 жыл бұрын
Do you buy one of those for each wheel or just one? Do you leave it in place or remove it after you have done the grease fill?
@2FAT4URACING3 жыл бұрын
You just buy one and put it in each wheel grease that wheel then take it out and move on to the next one.
@Mike-mn9xo4 жыл бұрын
How many miles do you have to grease these?
@2FAT4URACING4 жыл бұрын
I don’t know the exact maintenance interval. Or if there is one, but I try to do it every second oil change
@therowdyboysnetwork28273 жыл бұрын
How is your x3 holding up?
@2FAT4URACING3 жыл бұрын
Outstanding!! it’s the best on the market!!
@gustavoavina31365 жыл бұрын
what grease did you used?
@2FAT4URACING5 жыл бұрын
Gustavo Avina just some basic grease
@13salinaspride Жыл бұрын
Just pulled me 2023 can am took it apart bone dry I have only put 200miles on it. Just grease everything, SMH good thing I am old about maintenance
@nitroboost4 жыл бұрын
You sure you're supposed to pump grease until you see it? I thought these were sealed bearings, and you've pushed it past the seal when you see it coming out. I think that explains why there "isn't much from the factory", it's intentional and you can't see it. Fill the bearing up for sure though.
@Kyle-fu6en3 жыл бұрын
Bingo
@johnboticki91544 жыл бұрын
There are ones that are made in America, or at least claim to be.
@tonywohlgemuth63184 жыл бұрын
Watch this about this subject: kzfaq.info/get/bejne/l9OipLtpyLS9gGg.html
@jimmydesperado29362 жыл бұрын
Greaser made in China....a long with 1/2 the components on your machine.