great video! I tried this, but many screws were impossible to remove! I just gave up rather than end up stripping them.
@CamMaker2019 Жыл бұрын
Thank you
@CamerasLensesEtc11 ай бұрын
Thank you for your comment & you're welcome!
@shaniatwain19953 жыл бұрын
Thank you for this! Made my task so much easier. I have a 5d ii that won't turn on, tried all of the usual things, removing battery, card, clock battery, etc. The battery door switch is working correctly. I figured it was a fuse, did this test and all of them passed. Any idea of what else I should look into?
@CamerasLensesEtc3 жыл бұрын
Hard to tell... in this case, I start to replace camera parts from a working 5D MK II. I would start with the power PCB (where the fuses are), then the main PCB. Also, seems obvious, but don't forget to check your camera with an another battery... sometimes batteries fail.
@gkw83 Жыл бұрын
Try to reinsert the cables properly on the main pcb.happened to me
@beplh5242 Жыл бұрын
How do you keep the screws organized?
@CamerasLensesEtc11 ай бұрын
I have a paper divided into sections, and I put the screws there at the positions how they came off. I have a video where you can see that (50D disassembly), link is in the description below.
@douglasdonascimentopereira14822 жыл бұрын
excellent video, very good your channel I always learn a lot, I have a canon 5D MK II and the flex cable connector lock broke, where I could only buy the connector to change or where I could get a scrap board to remove this piece ? if you can help me, thank you very much.
@CamerasLensesEtc2 жыл бұрын
- ebay or aliexpress, sometimes they sell PCBs - local camera repair shop, maybe they have a broken PBC with a working connector you need Keep in mind that you need a heatgun to remove and install the connector, and it is not that easy to do it.
@douglasdonascimentopereira14822 жыл бұрын
@@CamerasLensesEtc thank you very much, i will look in these places, once again congratulations for the videos.
@bl4dolicy2 жыл бұрын
I have the same problem with canon 60d
@CamerasLensesEtc2 жыл бұрын
Check the fuses, maybe that is the problem.
@01983LFA4 ай бұрын
I have exactly problem in my camera
@TheJackMarcin Жыл бұрын
there is a rubber flap that is used in the battery compartment, the flap is used when you use a dummy battery. My flap just broke and i am looking to replace it - how big of a job is it? it looks like i have to completely disassemble the camera?
@CamerasLensesEtc Жыл бұрын
Well, not completely, but you would have to remove most of the covers of the camera. Actually, I wouldn't bother to replace that rubber, the camera can be used perfectly without it.
@TheJackMarcin Жыл бұрын
@@CamerasLensesEtc Thanks for the response and yeah i agree with you, it's just now it is less waterproof- so it just bothers me a lil. I'm not going to invest hours of work and potentially brick my camera because of a tiny piece of rubber. So if anyone has this issue- really think about whether its worth it. I was hoping it was an easier job than it appeared -it probably isn't easy at all!
@lucydevero85663 жыл бұрын
Hi I have a 5dii its been dropped with no visible signs of damage. When I turn it on now the back screen lights up a dark blue only the top screen has nothing .the shutter works in all speeds What could be wrong please can you help solve the problem . Thank you dev.
@CamerasLensesEtc3 жыл бұрын
Hard to tell by this... the solution is to have a working, same camera, and start replacing the parts of the non-working camera, and then you can see if the part is working or not, and sooner or later you find out which part is damaged.
@ivanskinner29433 жыл бұрын
Dear Sir, is there the same problem with Canon 5D3?
@CamerasLensesEtc3 жыл бұрын
I don't know. I heard that the Canon 7D has the same problem, and the repair is basically the same, but if you have the same symptoms with your 5D MK III, then check the fuses.
@ivanskinner29433 жыл бұрын
@@CamerasLensesEtc Thank you, most likely I will send the camera to Canon Service Center. I hardly think I can do the things you did in this video!