Great to hear! Thanks bro...

Thank you sir

Thank you sir!

you're welcome

thank you, sir!

Thank u sir

sir, try checking the existing switch beside your door by using a tester

Finally I found the wires to connect the lock/unlock (they were on the left hand side pillar. Now I would like to connect the brown from keyless module to hazard lights. I tried to connect the to hazard button on the dash but don't work... any ideas? The plug for this button has 4 cables. 2 with signal, 2 without. The first ones don't trigger when I lock the car from the remote control

Did you solve this problem?

maghimo ra ta ana puhon kol

This is the link brother for manual switch lock/unlock kzfaq.info/get/bejne/fK6kpL2DspzSlmw.html

you can use either of the two depending the manufacturer, but most of the modules now are negative trigger. Always refer to owner's manual before installation

master actuator has 5wires. slave actuator has 2wires(blue/green)

@@chomytuideas1784 yes..same in video..master slave 5 wire..on the module 2 wire input from the alarm receiver..so use the negative trigger direction rite??so in alarm module setting output for negative trigger only..its true??

@@mohamadfauzery yes, 2 wires only (white & brown). you can use negative as trigger output

Yes. But you have to use 2 relays as your module. I will upload soon of this method. Stay tuned. Thank you 👍

@@chomytuideas1784 Nice, thank's for the tip!

I need this same thing

Yes sir

Welcome boss

This diagram is not for power windows... This video may help you>>> kzfaq.info/get/bejne/eNldlNt8yL7Pmqs.html

yes sir

Master actuator have 5 wires in order to give signals to slave actuators. When you lock/unlock the master actuator, slave actuators will also lock/unlock simultaneously

@@chomytuideas1784 thanks for a quick answer so i want to lock or unlock the passenger door from driver door, would u tell me if i need a 5 wire actuator in driver door and 2 wire actuator in passenger door or both doors should have a 5 wires actuator? else i want to lock or unlock both doors with a keyless fog

@@Janetteag only the driver's door should be installed with master actuator. The rest will be slave actuators

thanks again! so any brand that you recommend for those actuator

@@Janetteag any brand will do sir

Anong ibig mong sabihin sa 5pin switch boss?

@@chomytuideas1784 maglalagay kasi ako switch sa loob ng sasakyan boss para sa door lock. Pano wirings non?

@@jcorpano9405 connect mo sa blue wire boss

Manual switch lock/unlock 5pin switch kzfaq.info/get/bejne/fK6kpL2DspzSlmw.html

you need to put a rectifier diode(6A10) or (1N4007) each wire for the signal light

@@chomytuideas1784 oow..u got the diagram??

@@mohamadfauzery yes. Watch the the video i uploaded. The brown wire is divided into 2 wires then put a diode each of the wires going to signal light

@@chomytuideas1784 nice sir...u are so good n very kind...tq for your info..i try find the way..i think my mine for headlight output not for signal..if connect to headlight only use 1 wire output..what do you think??is it true??

connecting to headlight is not recommended. The design is for signal light only.

Pwde ra boss

@@chomytuideas1784 tnx bos

You have to use relays

@@chomytuideas1784 I have a couple relays but Im not sure how to hook them up

Soon ill make diagrams using relays

@@chomytuideas1784 thank you!

Salamat mego. Asa man ka dapit sa tampi?

👍

yes boss..negative

Gagamit po kayo ng tester boss para malaman kung positive or negative

you're welcome po

i mean pag di nakakaconnect ung brown white ng central module sa remote module, gumagana central lock. nagoopen lhat ng pinto pag manual ko inopen ung lock sa drivers door. pero pag nakaconnect ung brown white ng central lock module, magoopen lang ung mga pinto pag napress sa remote.

sundin mo lang yung last diagram boss. halos lahat ng module ngayon ay negative trigger. bihira nalang yung positive trigger.

Dapat master actuator ang nasa driver side boss para gagana lahat ng slave actuator pag palo ng master actuator

@@chomytuideas1784 sir tama naman po diagram ko. master actuator nsa drivers door. pag nag lock or unlock ako sa master actuator nagana mga slave actuator pag di nakaconnect ung brown white wire sa alarm remote module . kaso di naman nagana remote lock. kung nakaconnect naman lahat ng features nagana,like auto lock sa break,unlock sa engine off,etc.ganun po ba talaga. or may problema nabili ko. last diagram po sinundan ko. salamat po

@@jillsael8306 parang may prob yata sa module pag ganyan boss

May positive po na trigger. Meron din negative na trigger

baka yung wire sa door switch sir mali ang koneksyon

@@chomytuideas1784 hindi kuna yun kinabit sir.. kasi wala naman ganun sa sasakyan ko.. isuzu hilander.. ang kinabit ko lang na wire ay sa.. horn,parklight,positive,ground at yong papuntang central lock lang..

@@reymundnacino7773 hindi kay defective yung nabili mo sir?

@@chomytuideas1784 ok naman xa sir nong kinabit ko.. nagamit kopa xa ng isang araw.. pwd kaya e resset yun sir

@@reymundnacino7773 di ko pa natry kung pwde ba yan ireset sir

Icompare mo lang sir yung mga colors ng wire

magkkaiba po ser..pti 10 po yung wires ng bago... 9 lng po sa stock ser

@@johannsbeleno3232 ganito gawin mo sir. Itest mo yung stock na wires yung mga functions nya.

Anu sasakyan nyo boss?

@@chomytuideas1784 Hyundai accent 2017 boss

@@markgamalog293 mostly pag ganyan boss meron na yang central lock na stock pero walang remote. Kaya dinagdagan lang ng actuator na connected sa alarm module

@@chomytuideas1784 pano malalaman pag sira ung actuator boss? Minsan kasi gumagana minsan hindi... Tapos pag gumana naman eh may sound sya

hindi sir

Pink wire

@@chomytuideas1784 There is no any pink wire in my Hyundai Eon Company fitted central locking

if there is none, your module is not compatible for buzzer

@@chomytuideas1784 okay... but there are 2 wires one is blue and one is Green, When i use buzzer in green wire with ground wire then the buzzer works while lock the car and when I use buzzer in blue wire with ground wire then the buzzer works while unlocking the car. May be these wires are going to Door gun, Can we use buzzer in this wires?

@@lordof_goodness do not connect the buzzer to those wires. better connect the buzzer to signal light wires using rectifier diode

yes sir.para kahit nakaoff yung susi, gagana pa din ang central lock

@@chomytuideas1784 salamat po ng marami idol

ano recommend nyo central lock with remote para sa corollabigbody sir?

@@vhinez01 aventail sir pwde na.or kahit anong brand sir bsta tignan mo muna mga review sa online bago ka bumili sir

slamat po sir..from san fernando pampanga po

yes boss. Meron tayong mga actual installationsp. check mo lang mga videos ko. Thanks

@@chomytuideas1784 Hello sir, Yung ganyan po na keyless entry wala po syang siren feature. pero mabasa ko po sa manual. Iprogram sya sa power window feature? Paano po yun

Wala po syang siren sir. Di ko din natry yung sa features nya sa window sir

@@chomytuideas1784 Wala na ibang choice ng wiring sir maliban sa lagyan ng diode yung sa signal

@@chomytuideas1784 Pwede po kaya sya itap sa wire ng central lock?Para pag nag lock unlock natitrigger fin po siren?

Because you did not watch the full video