Carbon Fiber Brushless Motor Mount Installation Proboat UL-19

Carbon Fiber Brushless Motor Mount Installation Proboat UL-19 - Water Cooled Motor Mount

Рет қаралды 8,819

Жыл бұрын

XLX2 HYDRA
www.avantlink.com/click.php?t...
PRO BOAT UL-19 30" HYDROPLANE
www.avantlink.com/click.php?t...
rtr%2FPRB08028V2.html
EPOXY/CARBON FIBER
www.ebay.com/itm/115173374556...
40mm MOTOR MOUNT
www.offshoreelectrics.com/pro...
OXIDEAN 42 HIGH RAKE
oxideanmarine.com/products/co...
OXIDEAN 4082 2200KV 6 POLE
oxideanmarine.com/products/rc...
OXIDEAN MARINE 200A ESC
oxideanmarine.com/products/ox...
QUASAR RX/TX
oxideanmarine.com/products/ox...
MAD LIZARD
HYDRO STRUT GAUGE (RIDE HEIGHT GAUGE)
www.madlizardproducts.com/pro...
ZIPKITS UPGRADED FLEXCABLE .187 3/16
zippkits.com/index.php?main_p...
UPGRADED COLLET 5mm to .187
zippkits.com/index.php?main_p...
DYNIMITE GPS
www.avantlink.com/click.php?t...
SMC DV EXTREME 5200 135C
www.smc-racing.com/index.php?...
SMC HCL-HP 7600 150C
www.smc-racing.com/index.php?...
DYNIMITE STARTUP TOOL SET
www.avantlink.com/click.php?t...
DYNIMITE MARINE GREASE
www.avantlink.com/click.php?t...
SPEKTRUM BATTERY'S
www.avantlink.com/click.php?t...
Thanks for watching ironclad rc tinker test and tune everything rc
Personal contact information ironcladedout@gmail.com

Пікірлер: 52

@autoprefecture6591 3 ай бұрын

these videos are a huge help! currently doing an inlay an bunch of upgrades to my big mono hull

@IRONCLADRC 3 ай бұрын

Good luck with your build I'm here if you have any questions. BG4L

@5chevygeoff Жыл бұрын

Thank you for sharing so much building info with everyone. Even as an experienced (older) builder I learn things from your videos. I use a cut off from a drill bit in my collet with a wrap or 2 off masking tape to make it a neat fit in the stuffing tube. This helps if you can't see the alignment or are having trouble holding the motor in place. Keep up the good work Mr Big B

@IRONCLADRC Жыл бұрын

I'll keep that in mind, thanks for watching

@mildtowildrc7343 Жыл бұрын

Now you see why mine has the factory tray out and run the carbon fiber tray😂That factory tray is tough but heavy,and easiest way to save weight👍Nice build Big B and can’t wait to see her run again.

@norcalrc Жыл бұрын

The ul 19 is gonna be a beast bro. Can’t wait to see it fly. Nothing better than a stiff hull

@rodneyrasmussen1199 Жыл бұрын

Can’t wait to see this thing go 100+, keep the videos coming Big B

@dennismatovich8411 Жыл бұрын

Great job, lookin good! I have been using dual lock by 3m as a velcro replacement.

@sjorswouda6865 Жыл бұрын

Ah ! At last. A w c motor mount.......nice job, realy nice.

@PigglyWigglyDeluxe Жыл бұрын

I love my UL. You’ve seen my UL on Reddit, too. I don’t love mine THAT much though, I appreciate 40mph. The rabbit hole goes deep for sure. The build looks epic, too rich for my blood but I love watching!

@frankmonthomery9570 Жыл бұрын

Awesome..and this is why I love your work ...

@Livlifetaistdeth Жыл бұрын

Awesome build!

@FrankyDigital2000 Жыл бұрын

This was really helpful! Thank you sir.

@robbomber984 Жыл бұрын

Gonna try a enlay of carbon fiber on the pathfinder build still thinking about theme of boat it's more orange then red so I'm thinking retro orange crush soda , been orange crushed. Was thing electronics tray but cant get the velez tray so I'm gonna do the same on my cat. Thanks for the videos I learned alot wish I seen some before I started some builds that turned out crappy .

@PigglyWigglyDeluxe Жыл бұрын

Give it wings that shit is gonna flyyyyyy

@andrewfrost4802 Жыл бұрын

Yeah good morning big B..

@peteroosterhoff8850 Жыл бұрын

Nothing wrong with epoxying the motormount and you did it very nice. We all got different ways to bond stuff. I use sealingbond used for car windows... Kind off a hassle because it stains (so i tape it), but is very, very strong en you can cut it when it has to come loose again (there will be remains after cutting because its so damn strong and you can use open can just for so long). You can nearly glue everything with it... This thing is going to fly, that's for sure...

@IRONCLADRC Жыл бұрын

Can you send a link for the adhesive

@peteroosterhoff8850 Жыл бұрын

@@IRONCLADRC brand is Sika. Called sikaflex260 or 522. It's a hybrid glue. It's used in car (for instance front window) and trailer builds (aluminium frame and sheets bonding). When dry it's almost resistant to all chemicals, uv, salt water, hi/low temps and so on. Don't know if its available in States, but i buy it at a local car parts store. Is especially ment for use in automotive industry...

@davidjohnson8474 Жыл бұрын

Im surprised you didnt trumpet the end of the stuffin tube? Id think then no worries about heat. Just something going through my head is all

@stevejackson3564 Жыл бұрын

Cool

@Mr.Blackhatt Жыл бұрын

let's goooOoOoooo BigB! 😁

@crutch958 Жыл бұрын

Freakin sweet bro now I see why you didnt run the Ul 19 as much those stress cracks are bad , I know there cosmetic but still would freak me out!

@IRONCLADRC Жыл бұрын

I was leery of pushing the boat to hard, still kinda worried about the sponsons.. I'm almost tempted to pull the foam and reinforce the sponson tips.. it would strengthen the hull but add more weight, Im also contemplating pour foam 🤔 decisions, decisions!

@PhilBender612 Жыл бұрын

Hey Im curious as to why you epoxied the motor mount directly to the hull of the boat in a permanent fixed position? The mount has all those holes on the sides for mounting, why not epoxy 2 blocks to the hull and then bolt the mount to the blocks...This way you still have some adjustability where you can slide the motor/mount fwd or back.

@IRONCLADRC Жыл бұрын

I've always Permanently mounted my motor mounts, using the holes in the side as epoxy dam holes for bonding. Never really thought about using the bottom rail holes for a removal mounting option, thanks for the tip, I've seen it done but never tried it myself.

@TheAWallace1212 Жыл бұрын

Beautiful build Big B!! I use Velcro as well & jam foam between batteries & top of hull to hold them in place. What are you going to do with the cooling jacket? Now I have to go sand my winglet 😂. Cool trick!!

@IRONCLADRC Жыл бұрын

I've got a shorter jacket that fits perfectly,

@55steviegreene Жыл бұрын

Lots of info B. Love the Carbon fiber loos great and works even better. Can you apply the Carbon Fiber to a plastic hull. Was wondering if that would work. Great build so far. It's going to haul ass

@IRONCLADRC Жыл бұрын

I've reinforced the seems on the bj42 with CF it actually stuck rather well considering.... if you attempt a CF inlay in a poly hull IMO use Gflex by wetsystem its made to flex with plastic/ abs/poly materials. It's expensive but from what I hear it's worth it

@gord1131 4 ай бұрын

Hey big B, I see in your last video you used a different epoxy to inlay the carbon fibre and then used bob smith in this video to help with putting on the motor mount. My question is could I use the bob smith industries epoxy to inlay a whole boat while thinning it with a bit of alcohol? Don’t have a lot of resources where I’m at but I do have the slow cure and was hoping that would be enough, going in my Proboat mystic 29 and it’s also my first time. Love your vids!

@IRONCLADRC 4 ай бұрын

Yea you can use the slow cure but you need to work quick, I wouldn't thin the epoxy to much when laying up carbon fiber you need it to be "sticky" so it holds everything down in place

@gord1131 4 ай бұрын

So what is the magic in a bottle that you use? I thought maybe a good video would be to show all the stuff in your workshop, and the workshop itself, might not be much for you but all the followers and fans would really enjoy it…… and also maybe showing yourself in front of the camera!!!!!!

@IRONCLADRC 4 ай бұрын

Probably denatured alcohol, been a while since I Made this video

@user-io7gq8ri6s 6 ай бұрын

Hi i ve a Llumar u8 1:8 scale from proboat and i would like to convert it into brushless. It s old, the only perfect thing is the body. Could you help me or gimme some infos? Thank you, if you are interested ill give you additional informations. Great channel. Ciao!

@05_caoquangbach21 26 күн бұрын

When you assemble the motor mount. Is better to loctite the screw or use the spring washer ?

@IRONCLADRC 26 күн бұрын

I'd use the spring washer on the rail mounting screws? I learned the hard way? Loc-tite dried hard! When I went to remove the motor I stripped all 4 loc-tighted screws.

@05_caoquangbach21 26 күн бұрын

@@IRONCLADRC What parts do you recommend using loctite?

@IRONCLADRC 26 күн бұрын

@05_caoquangbach21 definitely the motor head screws. All grub screws, Collet, steering, drive dog etc

@05_caoquangbach21 26 күн бұрын

@@IRONCLADRC thanks

@05_caoquangbach21 2 ай бұрын

Would super glue work fine connecting the mount to the hull? carbon mount and fiberglassed hull

@05_caoquangbach21 2 ай бұрын

Or should i use fiberglass resin and some chop up fiberglass

@IRONCLADRC 2 ай бұрын

I'd use epoxy resin, super glue will not hold

@sammumu4088 Жыл бұрын

Hi, i am building a boat and need your help. The boat is 70cm long it is a mono boat. The motor i will use, is a turnigy 3674 2200kv and 1750 watt with a 43 prop. My question is, i choose a 4,75mm flex shaft, is that the right decision? Or should i take a less diameter flex shaft? Regards

@IRONCLADRC Жыл бұрын

.187 with 3/16 stub shaft sounds about right, heavy duty cable so it shouldn't break.