【Carburetor cleaning XV125 Virago 125 & 250】fuel valve intake manifold Yamaha overflow ビラーゴキャブ分解＆清掃

Рет қаралды 35,455

2 жыл бұрын

Carburetor needs periodic maintenance. In this video I opened up the float chamber of the motorcycle carburetor and cleaned the float bowl.
I have also replaced the fuel valve (float valve) and the intake manifold. Float chamber actually can be opened up without removing the fuel tank and carburetor. Periodic maintenance can actually be done quite easily if the float bowl is the only area to inspect.
Needle valve set: part# 3CF141071000
www.bike-parts-yam.com/yamaha...
Carburetor joint: part# 4RF135860100
www.bike-parts-yam.com/yamaha...
Float bowl O-ring: part# 1HX141470000
www.bike-parts-yam.com/yamaha...
Related videos:
Chain replacement • 【XV125 Yamaha Virago 1...
Conventional battery • 【XV125】Conventional mo...
Virago sprockets • 【XV125】スプロケット交換 Remova...
Virago oil change • 【virago 125】ビラーゴ125オイル...
ヤマハビラーゴの125のキャブレター分解と清掃のやり方動画です。ビラーゴ250も同じやり方です。キャブは定期的なメンテナンスが必要です。オーバーフロー等の問題もキャブのメンテを定期的に行う事で発見・解決する事が出来ます。
ニードルバルブがすり減ったり、バルブのフィルターが汚れる事でオーバーフローが起こることもあります。フロートチャンバー自体はバイクは外さずに分解できますので定期的にチェックすると良いですね。
#yamaha #virago #carburetor

Пікірлер: 28

@motorpsycho2989 2 жыл бұрын

0:51 Carburetor removal 5:21 Disassembly & inspection 8:40 Cleaning 9:48 New fuel valve 11:39 Reassembly & installation 14:10 Pre-ride test

@Booty_Bender 2 жыл бұрын

This video is a lifesaver, thank you so much

@motorpsycho2989 2 жыл бұрын

Glad to hear that you find it useful.

@minermac9024 Жыл бұрын

Thank you! this was such a big help! Also I like the "midnight special" rendition at 8:25

@motorpsycho2989 Жыл бұрын

You are welcome!

@armorking555 2 жыл бұрын

Great video, I got re jet my carb on my 125cc as silver tail exhaust fitted when I got the bike and it’s struggling to get to 40-50mph, I did fit a K&n air filter which really helped so I believe it’s not getting enough air. Thank you for your video

@armorking555 2 жыл бұрын

Do you know the mm of the bolts that hold the carbs as mine are rounded off eg m4

@Punkerage Жыл бұрын

ありがとうございます!助かります melhor video de limpeza de carburador em virago no youtube. muito obrigado mesmo

@Oxider4 Жыл бұрын

Great video. Nice!

@arielriveross.7918 9 ай бұрын

Great video, you saved me. Im subscribing

@romerkilic7895 Жыл бұрын

Thanks from Istanbul !

@finnfinnone Жыл бұрын

Great vdo⭐tnx for sharing

@motorpsycho2989 Жыл бұрын

Thanks!

@ervinszabo6221 2 күн бұрын

What's the float height measurements?

@khatdubell Жыл бұрын

At 4:59 Do you know what that part is below the choke cable and to the left of the throttle? That little brass nozzle? Mine just broke.

@serviaellas9293 2 жыл бұрын

ΤΕΛΙΑ μιχανη η βιραγκο πολύ θα ήθελα να έχω μια τέτοια μιχανη στην Ελλάδα είναι πανάκριβα i lave Virago

@forrest474 11 ай бұрын

Hi, I'm having troubles with my Yamaha xvs 125 Dragstar Carburetor. Need him to replace. By the research Virago and dragstar supposed to have same carburetor ( Mikuni BDS 26 ) but this original one is not anymore on the market. There are some options to buy some other replacements but in all cases it says it only fit to the virago 125/250. So now I'm not sure If I can try to use this one or rather not. Original bds 26 comes with some sort of cable with 3 pin slot that supposed to be connected with the bike but there new replacements does'nt have it. Would that be a problem? Thanks a lot for any advice

@KAPANGAAAMASTER 3 ай бұрын

Why did Yamaha made a small motorcycle carburetor system so complicated...

@tanartpreeyawatanawong3841 2 ай бұрын

hello ! i have a question to ask. i cleaned the carburetor and install it on my bike but it won't last 2 days because the front side of the engine's spark plug is wet with gasoline. what do i need to change on carburetor to get it run fine ? (my bike problem is it started on single cyclinder , the front cycline won't work)

@sansguerra2265 Ай бұрын

Did you measure float height? Sounds like the bike may be running on a rich mixture

@HighAway Жыл бұрын

trying to look for the choke part... could you point that out? I wanna see to give an idea cuz I couldn't find it on my bike.

@motorpsycho2989 Жыл бұрын

It’s next to the throttle cable behind the fuel pump.

@bobansupergenije7512 Жыл бұрын

Bravo

@juergenkoller 2 жыл бұрын

Many thanks for the video from Germany. My Virago is an XV 125 5AJ from 1998 Now i have to change the carburetor complete. I got a complete new one for about 65 €uros / Dollars. So its easier to change and i dont have to repair it or change expensive parts. But ithe new one is the carburetor for the XV 250 (main jet is the difference said the seller.) Is it right that i only have to change the main jet and everything is fine. Ok set the idle speed is one point i have to do at first after restarting the bike. Is there something else to consider? Is it only the main jet that i have to change? Iam not a mechanic thats the problem.

@motorpsycho2989 Жыл бұрын

I am not 100% positive, but I believe the carburetor components are all the same excepts for the jets between XV125 & XV250. Check this link and compare it to the jets you have. It's for 1998 XV125. www.bike-parts-yam.com/yamaha-motorcycle/125-MOTO/1998/VIRAGO/XV125/CARBURETOR/66_6628-6628/B9/0/33506

@khatdubell Жыл бұрын

Why fuzzy gloves?