so no turkish 8mm in this then

@@mwmwmwmwmmdw That would be a "NO" as that stuff is generally regarded as a proof load for every shot.

Which is better 44 bore rifle and 223 bore rifle?

@@ranaaamiriqbalchouhan100 That depends on what the target is and what the distance.

I agree, there does not have to be a particular "purpose" other than the experimenting and of course have a bit of fun along the way. It's even better when you can do it with a rifle that you paid $35 for!

Yeah I've heard of those but I dont have a 3D printer and the folks making them did not seem interested in shipping to Canada.

Thanks David.

Yeah, not much point in putting the old ones to harsh use with full power ammo. I shoot only cast in my Commission rifle as well, with all the sight adjustment its still possible to hit the target even with the lower velocity cast loadings.

With the Carcano variants being one of the the few relatively affordable and available military surplus rifles left I don't blame you.

Yeah, was that the Ivor Johnson 50 cal that had a "shell holder" type removable bolt?

The Noreen ULR was one.

Fortunately the sights were close to the point of impact with this load which made it possible to get a few rounds on target.

I would not fire full power surplus ammo, or European specification hunting ammo in one of these, but cast loads or North American loaded "8mm Mauser" power loads should be fine if the headspace is OK. It's not that I think the action would not hold up with full power loads (that's what they were converted to fire), it's just that the recoil and blast would be horrendous and therefore most unpleasant. The stocks are very short and the carbine weighs very little so I cannot imagine they would be pleasant to fire with full power loads.

@@314299 Yeah, you are right, the blast and recoil are probably gonna be quite bad if you use full power ammo out of these. Concerning the stability of the action, there is probably no significant danger, as you said. Plus, over here those guns will have CIP proofing, meaning that they have been fired with loads that have 20% higher gas pressure that the strongest commercially available loads. But still, since my collector buddy said he doesn't shoot his at all, I got some doubts that I can't shake off. And he's not a person to shy away from something that seems a little risky.

Ha ha, very punny. As luck would have it this particular load actually shoots somewhat close to the sights, another plus to the Loverin style 323470 bullet.

@@314299 That is a big plus about the sights :)

@@Gungeek I think they supposed to be a 250 or 300 meter zero?

@@314299 I think the fixed sight ones are 200m.

It seems that most folks who have an 8mm converted Carcano have not shot them. If all they have access to it is surplus type ammo that's probably a good thing.

I suppose they are too uncommon and making an "8mm" clip would not be a profitable venture.

@@314299 I see.

The 8mm conversions will not work with a 6.5mm enblock clip, as the 8mm case is fatter. Apparently there were some 8mm specific enblock clips made but they are basically unobtainable. Single loading right into the chamber will not work on this example, as the front of the extractor is flat and will not "jump" the rim of the case. The Carcano is a "controlled feed" action, so even if a given example will snap over the rim of a round if single loaded it's a good way to break the tip off the extractor. The best solution is to use one of the single shot adapters that is loaded into the action like a clip, then a single round can be dropped in and will feed correctly. As I don't have one of those I use the rather sketchy method shown of removing the bolt and placing a round under the extractor - I don't recommend anyone else do this, I'm just showing what I have done. The mold I use is the Lyman 323470, it is a "Lovern" style mold and a good one for various 8mm's.

I've used 2400 with cast bullets in the 8mm Mauser and it is a good performer.

Yes, it's a 323470. I've corrected that. I was thinking of the sizing die I use, which is the .325" one.

@@314299 Just a great informative video as usual, please keep up with your great videos, pay no attention to the idiot anti-gun morons in toronto or the rabid anti-gun Quebec group!!

Any particular reason why?